2011-2013 Land Cruiser · Service Manual Brake

REMOVAL

Removal / installation · Vehicles built from Jan 2012

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012


1. PLACE FRONT WHEELS FACING STRAIGHT AHEAD

2. PRECAUTION

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).


3. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
  1. Disable the Autoaway/Return function by changing the customize parameter (Click here).

    NOTICE:
    Record the current customize parameter setting (whether the Autoaway/Return function is enabled or disabled) in order to restore the current setting after finishing the operation.

    HINT:
    Performing the above operation causes the Autoaway/Return function to be disabled when the ignition switch is turned off.

  1. Turn the ignition switch on. Operate the tilt and telescopic switch to fully extend and lower the steering column.

  1. Turn the ignition switch off and disconnect the cable from the negative (-) battery terminal.

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


4. REMOVE LOWER NO. 2 STEERING WHEEL COVER

  1. B189186E01
    Detach the 2 claws and remove the steering wheel cover.


5. REMOVE LOWER NO. 3 STEERING WHEEL COVER

  1. B181563
    Detach the 2 claws and remove the steering wheel cover.


6. REMOVE STEERING PAD

  1. B187261E01
    Using a T30 "TORX" socket wrench, loosen the 2 screws until the groove along the screw circumference catches on the screw case.

  1. B181568
    Pull out the steering pad from the steering wheel, as shown in the illustration. Then support the steering pad with one hand.

    NOTICE:
    When removing the steering pad, do not pull the airbag wire harness.

  1. Disconnect the horn connector.

  1. Disconnect the 2 connectors and remove the steering pad.

    NOTICE:
    When handling the airbag connector, take care not to damage the airbag wire harness.


7. REMOVE STEERING WHEEL ASSEMBLY
  1. Remove the steering wheel set nut.

  1. C172673E03
    Put matchmarks on the steering wheel and main shaft.
    Text in Illustration 
    *a
    Matchmark
    *b
    Hold
    *c
    Turn

  1. Using SST, remove the steering wheel assembly.

    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05020, 09954-05011)


8. REMOVE LOWER STEERING COLUMN COVER

  1. C179481
    Remove the 3 screws.

  1. Detach the 2 claws to remove the lower steering column cover.

    NOTICE:
    Do not damage the tilt and telescopic switch.


9. REMOVE UPPER STEERING COLUMN COVER

  1. C179482
    Detach the 4 clips.

  1. Detach the claw to remove the upper steering column cover.


10. REMOVE SPIRAL CABLE SUB-ASSEMBLY

  1. B181593
    Disconnect the connectors from the spiral cable with steering sensor.

    NOTICE:
    When handling the airbag connector, take care not to damage the airbag wire harness.

  1. Detach the 3 claws and remove the spiral cable with steering sensor.

  1. C110478E03
    Detach the 6 claws and remove the spiral cable from the steering sensor.


11. REMOVE STEERING ANGLE SENSOR

  1. C139815E01
    Detach the 6 claws and remove the steering angle sensor.

← REMOVAL (Sep 2011 – Dec 2011)INSPECTION (from Sep 2011) →