Driver Side Door Entry Lock and Unlock Functions do not Operate
Circuit diagnosis · Vehicles built from Jan 2012
Versions by build date: Sep 2011 – Dec 2011 from Jan 2012
DESCRIPTION
When the driver side door entry lock and unlock functions do not operate, one of the following may be malfunctioning: 1) power door lock system, 2) driver side door electrical key oscillator, or 3) certification ECU (smart key ECU assembly).WIRING DIAGRAM


INSPECTION PROCEDURE
| 1. CHECK POWER DOOR LOCK OPERATION |
When the master switch assembly door control switch is operated, check that the locked doors unlock.
- OK:
- Door locks operate normally.
|
|
||||
| OK | |
| 2. READ VALUE USING INTELLIGENT TESTER (DOOR LOCK POSITION SWITCH) |
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the intelligent tester on.
Enter the following menus: Body / Main Body / Data List.
Read the Data List according to the display on the intelligent tester.
Main Body Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
D Door Lock Position SW
Driver side door lock position switch signal / ON or OFF
ON: Driver side door unlocked
OFF: Driver side door locked
-
- OK:
- On the intelligent tester screen, the display changes between ON and OFF as shown in the chart above.
|
|
||||
| OK | |
| 3. READ VALUE USING INTELLIGENT TESTER (TOUCH SENSOR) |
Using the intelligent tester, read the Data List.
Entry & Start Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
D-Door Touch Sensor
Driver side door touch sensor / ON or OFF
ON: Touch sensor touched
OFF: Touch sensor not touched
-
D-Door Trigger Switch
Driver side door outside handle lock switch / ON or OFF
ON: Entry lock switch pushed
OFF: Entry lock switch not pushed
-
Result Result
Proceed to
Display changes according to manual operation
A
Display does not change according to manual operation
B
|
|
||||
| A | |
| 4. CHECK WAVE ENVIRONMENT |
Bring the electrical key transmitter near the driver side door outside handle, and perform a driver side door entry lock and unlock operation check.

- NOTICE:
- If the key is brought within 0.2 m (0.656 ft.) of the door handle, communication is not possible.
- HINT:
- When the electrical key transmitter is brought near the driver side door outside handle, the possibility of wave interference decreases, and it can be determined if wave interference is causing the problem symptom.
- If the operation check is normal, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.
- When the electrical key transmitter is brought near the driver side door outside handle, the possibility of wave interference decreases, and it can be determined if wave interference is causing the problem symptom.
Result Result
Proceed to
Operation check fails
A
Operation check is normal
B
|
|
||||
| A | |
| 5. PERFORM KEY DIAGNOSTIC MODE INSPECTION |
Diagnostic mode inspection (driver side door electrical key oscillator).

Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the intelligent tester on.
Enter the following menus: Body / Entry & Start / Key Communication Check / Overhead + Driver Side.
When the electrical key transmitter is in the position shown in the illustration, check that the wireless door lock buzzer sounds.
- HINT:
- If the buzzer sounds, it can be determined that the driver seat outside transmitter is operating normally.
- OK:
- Wireless door lock buzzer sounds.
|
|
||||
| OK | ||
| ||
| 6. CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] - DOOR ELECTRICAL KEY OSCILLATOR) |
Disconnect the E29 ECU connector.

Disconnect the z24 or z22 oscillator connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
- for LHD:
Tester Connection
Condition
Specified Condition
E29-5 (SEL1) - z24-4 (SEL)
Always
Below 1 Ω
E29-33 (CLG1) - z24-10 (CLG)
Always
Below 1 Ω
E29-34 (CG1B) - z24-5 (CLGB)
Always
Below 1 Ω
E29-5 (SEL1) - Body ground
Always
10 kΩ or higher
E29-33 (CLG1) - Body ground
Always
10 kΩ or higher
E29-34 (CG1B) - Body ground
Always
10 kΩ or higher
- for RHD:
Tester Connection
Condition
Specified Condition
E29-5 (SEL1) - z22-4 (SEL)
Always
Below 1 Ω
E29-33 (CLG1) - z22-10 (CLG)
Always
Below 1 Ω
E29-34 (CG1B) - z22-5 (CLGB)
Always
Below 1 Ω
E29-5 (SEL1) - Body ground
Always
10 kΩ or higher
E29-33 (CLG1) - Body ground
Always
10 kΩ or higher
E29-34 (CG1B) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 7. CHECK HARNESS AND CONNECTOR (DOOR ELECTRICAL KEY OSCILLATOR - FRONT DOOR OUTSIDE HANDLE) |
Disconnect the z23 or z21 handle connector.

Disconnect the z24 or z22 oscillator connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
- for LHD:
Tester Connection
Condition
Specified Condition
z23-2 (ANT2) - z24-8 (ANT2)
Always
Below 1 Ω
z23-5 (ANT1) - z24-3 (ANT1)
Always
Below 1 Ω
z23-2 (ANT2) - Body ground
Always
10 kΩ or higher
z23-5 (ANT1) - Body ground
Always
10 kΩ or higher
- for RHD:
Tester Connection
Condition
Specified Condition
z21-2 (ANT2) - z22-8 (ANT2)
Always
Below 1 Ω
z21-5 (ANT1) - z22-3 (ANT1)
Always
Below 1 Ω
z21-2 (ANT2) - Body ground
Always
10 kΩ or higher
z21-5 (ANT1) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 8. CHECK HARNESS AND CONNECTOR (DOOR ELECTRICAL KEY OSCILLATOR - BATTERY AND BODY GROUND) |
Disconnect the z24 or z22 oscillator connector.

Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
- for LHD:
Tester Connection
Condition
Specified Condition
z24-1 (B) - z24-7 (GND)
Always
11 to 14 V
- for RHD:
Tester Connection
Condition
Specified Condition
z22-1 (B) - z22-7 (GND)
Always
11 to 14 V
|
|
||||
| OK | |
| 9. REPLACE DOOR ELECTRICAL KEY OSCILLATOR |
Replace the door electrical key oscillator (Click here).
| NEXT | |
| 10. CHECK DOOR ELECTRICAL KEY OSCILLATOR (OPERATION) |
Check that the entry function operates normally.
- OK:
- Operates normally.
|
|
||||
| OK | ||
| ||
| 11. REPLACE FRONT DOOR OUTSIDE HANDLE |
Replace the front door outside handle (Click here).
| NEXT | |
| 12. CHECK FRONT DOOR OUTSIDE HANDLE OPERATION |
Check that the entry function operates normally.
- OK:
- Operates normally.
|
|
||||
| OK | ||
| ||
