2011-2013 Land Cruiser · Service Manual Vehicle Exterior

DISASSEMBLY

Removal / installation · Vehicles built from Jan 2012

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

HINT:
  1. Use the same procedure for the RH side and LH side.
  2. The procedure listed below is for the LH side.


1. PRECAUTION

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).


2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


3. REMOVE FRONT DOOR OUTSIDE MOULDING SUB-ASSEMBLY LH (w/ Outside Moulding)

  1. B302178E01
    Put protective tape around the front door outside moulding sub-assembly LH.
    Text in Illustration 
    *1
    Protective Tape

  1. B302170
    Using a moulding remover, detach the 3 clamps and 11 clips, and remove the front door outside moulding sub-assembly LH.

  1. Remove any clips remaining on the door panel.

    NOTICE:
    Be careful not to allow any clips or pieces of clips to fall inside the door panel.


4. REMOVE FRONT DOOR LOWER FRAME BRACKET GARNISH LH

  1. B180820
    Detach the clip and claw, and remove the front door lower frame bracket garnish LH.


5. REMOVE COURTESY LIGHT ASSEMBLY (w/ Courtesy Light)

  1. E155940
    Detach the claw.

  1. Remove the courtesy light and then disconnect the connector.


6. REMOVE FRONT DOOR INSIDE HANDLE BEZEL LH

  1. B180816E01
    Using a screwdriver, detach the 4 claws and remove the front door inside handle bezel LH.

    HINT:
    Tape the screwdriver tip before use.

    Text in Illustration 
    *1
    Protective Tape


7. REMOVE FRONT UPPER ARMREST BASE PANEL LH

B180817
  1. Using a moulding remover, detach the 5 claws.

  1. Disconnect the connector and remove the armrest base panel.


8. REMOVE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY

  1. B182892
    Remove the 3 screws and master switch.


9. REMOVE DOOR ASSIST GRIP COVER LH

  1. B180819
    Using a moulding remover, detach the 8 claws and remove the door assist grip cover LH.


10. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY LH

  1. B310800E01
    Remove the 3 screws.

  1. Remove the 13 clips.

  1. Remove the front inner door glass weatherstrip LH together with the front door trim board sub-assembly LH by pulling them upward in the order shown in the illustration.

    HINT:
    Make sure that the pin labeled A in the illustration is detached from the door panel.

  1. Disconnect the connector.

  1. B180822
    Disconnect the 2 cables from the front door inside handle sub-assembly LH.


11. REMOVE FRONT INNER DOOR GLASS WEATHERSTRIP LH

  1. B310801
    Detach the 4 clips and remove the front inner door glass weatherstrip LH from the front door trim board sub-assembly LH.

    NOTICE:
    1. Squeeze the metal clip to remove it.
    2. The metal clip may be deformed if it is forcibly pulled.


12. REMOVE SEAT MEMORY SWITCH (w/ Seat Position Memory System)

B180823
  1. Disconnect the connector.

  1. Remove the screw and seat memory switch.


13. REMOVE FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY LH

  1. B235654
    Detach the 2 claws and remove the front door inside handle sub-assembly LH.


14. REMOVE FRONT DOOR INSIDE HANDLE BEZEL LH

  1. B235655
    Remove the 7 screws and front door inside handle bezel LH.


15. REMOVE OUTER REAR VIEW MIRROR ASSEMBLY LH

B180573E01
  1. w/ Power Mirror Control System:

    1. Disconnect the connector labeled A.

    2. Detach the clamp.

  1. Remove the 3 nuts and claw.

  1. Remove the outer rear view mirror.


16. REMOVE OUTER MIRROR CONTROL ECU ASSEMBLY (w/ Seat Position Memory System)

B180824
  1. Disconnect the 2 connectors.

  1. Remove the 2 screws and outer mirror control ECU.


17. REMOVE FRONT DOOR PANEL PROTECTOR LH

  1. B180835
    Remove the screw, and remove the front No. 1 door stiffener cushion and front door panel protector LH.


18. REMOVE FRONT NO. 1 SPEAKER ASSEMBLY
  1. Disconnect the speaker connector.

  1. B181519
    Remove the 4 screws and speaker.

    NOTICE:
    Do not touch the cone part of the speaker.


19. REMOVE SIDE AIRBAG SENSOR ASSEMBLY LH

  1. B181765
    Disconnect the connector.

  1. Remove the bolt and side airbag sensor.


20. REMOVE FRONT DOOR SERVICE HOLE COVER LH

  1. B182874
    Using a clip remover, detach the 9 clamps.

  1. Remove the bolt and disconnect the 2 connectors.

  1. Remove the front door service hole cover LH.

    HINT:
    Remove the remaining tape on the door.


21. REMOVE FRONT DOOR GLASS SUB-ASSEMBLY LH
  1. Driver Side:
    Temporarily install the multiplex network master switch.

  1. Passenger Side:
    Temporarily install the power window regulator switch assembly.

  1. Connect the cable to the negative (-) battery terminal.

  1. Move the front door glass sub-assembly until the bolts appear in the service holes.

  1. Disconnect the cable from the negative (-) battery terminal.

  1. B180832
    Remove the 2 bolts.

    NOTICE:
    Be careful when removing the bolts as the glass may fall and become damaged.

  1. B180833
    Remove the front door glass sub-assembly in the direction indicated by the arrows in the illustration.

    HINT:
    Remove the front door glass sub-assembly upward.

    NOTICE:
    Be careful not to damage the glass.

  1. Driver Side:
    Remove the multiplex network master switch.

  1. Passenger Side:
    Remove the power window regulator switch assembly.


22. REMOVE FRONT DOOR GLASS RUN LH

  1. B180838
    Remove the front door glass run LH.


23. REMOVE FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY LH

  1. B180840
    Remove the bolt and front door rear lower frame sub-assembly LH.


24. REMOVE LOWER DOOR FRAME GARNISH LH

  1. B180839
    Detach the claw and remove the lower door frame garnish LH.


25. REMOVE FRONT DOOR BELT MOULDING SUB-ASSEMBLY LH

B182606E01
  1. Put protective tape around the belt moulding.

  1. B182604
    Detach the claw and remove the belt moulding.


26. REMOVE FRONT DOOR REAR WINDOW FRAME MOULDING LH

B182608E01
  1. Put protective tape around the window frame moulding.

  1. Detach the clip and remove the double-sided tape to remove the window frame moulding.


27. REMOVE FRONT DOOR WINDOW REGULATOR SUB-ASSEMBLY LH

  1. B180836E03
    Loosen the temporary bolt.
    Text in Illustration 
    *1
    Temporary Bolt

  1. Remove the 5 bolts, and front door window regulator sub-assembly LH.

    HINT:
    Remove the front door window regulator sub-assembly LH through the service hole.

    NOTICE:
    Be careful when removing the bolts as the front door window regulator sub-assembly LH may fall and become damaged.

  1. Remove the front door window regulator sub-assembly LH and the front power window regulator motor assembly LH as a unit.

  1. Remove the temporary bolt from the front door window regulator sub-assembly LH.


28. REMOVE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

  1. B294158E01
    Using a T25 "TORX" driver, remove the 3 screws and motor.

    NOTICE:
    Be careful when removing the screws as the motor may fall and become damaged.

    Text in Illustration 
    *A
    for Models with Jam Protection Function on 4 Windows
    *B
    for Front Passenger Side, for Models with Jam Protection Function on Driver Door Window Only


29. REMOVE FRONT DOOR OUTSIDE HANDLE COVER LH

  1. B180841
    Remove the hole plug.

  1. Using a T30 "TORX" wrench, loosen the screw and remove the front door outside handle cover LH with the door lock cylinder installed.

  1. B180845
    Detach the 2 claws and remove the front door outside handle cover LH.


30. REMOVE FRONT DOOR OUTSIDE HANDLE ASSEMBLY LH

  1. B180849
    w/ Entry and Start System:

    1. Disconnect the connector.

  1. Using a T30 "TORX" wrench, loosen the screw.

  1. B180848
    Remove the front door outside handle assembly LH by sliding and pulling it in the direction indicated by the arrow in the illustration.

    NOTICE:
    If the release plate is not pulled and held when removing the front door outside handle assembly LH, the release plate will interfere with the front door outside handle assembly LH and become damaged.


31. REMOVE FRONT DOOR FRONT OUTSIDE HANDLE PAD LH

  1. B180857
    Detach the 3 claws and remove the front door front outside handle pad LH.


32. REMOVE FRONT DOOR REAR OUTSIDE HANDLE PAD LH

  1. B180858
    Detach the 2 claws and remove the front door rear outside handle pad LH.


33. REMOVE FRONT DOOR LOCK ASSEMBLY LH

  1. B180842
    Using a T30 "TORX" wrench, remove the 3 screws.

    HINT:
    Remove the door lock through the service hole.

    NOTICE:
    Be careful when removing the screws as the door lock may fall and become damaged.


34. REMOVE FRONT DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY LH

  1. B180843
    Remove the front door lock remote control cable assembly LH.


35. REMOVE FRONT DOOR INSIDE LOCKING CABLE ASSEMBLY LH

  1. B180846E01
    Using a screwdriver, detach the 3 claws.

    HINT:
    Tape the screwdriver tip before use.

    Text in Illustration 
    *1
    Protective Tape

  1. B180847
    Remove the front door inside locking cable assembly LH.


36. REMOVE FRONT DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY LH

  1. B180851
    Using a T30 "TORX" wrench, loosen the screw.

  1. B182884
    Detach the 2 claws. Slide the front door outside handle frame sub-assembly LH and No. 2 electrical key wire harness to remove it.

    HINT:
    Remove the front door outside handle frame sub-assembly LH through the service hole.


37. REMOVE NO. 2 ELECTRICAL KEY WIRE HARNESS (w/ Entry and Start System)

  1. B180850
    Disconnect the connector.

  1. Detach the 3 clamps and remove the wire harness from the front door outside handle frame sub-assembly.


38. REMOVE FRONT DOOR LOCK OPEN ROD LH

  1. B180852
    Remove the front door lock open rod LH.


39. REMOVE DOOR ELECTRICAL KEY OSCILLATOR (w/ Entry and Start System)

  1. B180853
    Remove the screw and door electrical key oscillator.


40. REMOVE FRONT NO. 2 DOOR STIFFENER CUSHION

  1. B183088
    Remove the 2 bolts.

  1. Detach the 2 clamps and front No. 2 door stiffener cushion.


41. REMOVE FRONT DOOR CHECK COVER LH (w/ Cover)

  1. B180856
    Remove the front door check cover LH.


42. REMOVE FRONT DOOR CHECK ASSEMBLY LH

  1. B155785
    Remove the bolt, 2 nuts and front door check assembly LH.

    NOTICE:
    Be careful when removing the bolt and nuts as the front door check assembly LH may fall and become damaged.

    HINT:
    Remove the front door check assembly LH through the service hole.


43. REMOVE FRONT DOOR WEATHERSTRIP LH

  1. Using a clip remover, detach the 21 clips and remove the front door weatherstrip LH.

    B309311E01

    HINT:
    If clips are damaged during removal, replace them.

    Text in Illustration 
    *A
    w/ Spot Cover
    *B
    w/o Spot Cover
    *1
    Double-sided Tape
    -
    -

← DISASSEMBLY (Sep 2011 – Dec 2011)ADJUSTMENT (from Sep 2011) →