Rear Door LH Entry Lock Function does not Operate
Circuit diagnosis · Vehicles built Sep 2011 – Dec 2011
Versions by build date: Sep 2011 – Dec 2011 from Jan 2012
DESCRIPTION
If the rear door LH entry lock function does not operate but the entry unlock function operates, the communication line between the vehicle and electrical key transmitter is normal. The part at fault may be an entry lock switch circuit (certification ECU (smart key ECU assembly) → rear door outside handle LH (entry lock switch) → rear door electrical key oscillator LH).- HINT:
- For vehicles with entry function for rear doors.
WIRING DIAGRAM


INSPECTION PROCEDURE
| 1. CHECK POWER DOOR LOCK OPERATION |
When the master switch assembly door control switch is operated, check that the locked doors unlock.
- OK:
- Door locks operate normally.
|
|
||||
| OK | |
| 2. READ VALUE USING INTELLIGENT TESTER (DOOR LOCK POSITION SWITCH) |
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the intelligent tester on.
Enter the following menus: Body / Main Body / Data List.
Read the Data List according to the display on the intelligent tester.
for LHD
Main Body Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
DR Door Lock Position SW
Driver side rear door lock position switch signal / ON or OFF
ON: Driver side rear door unlocked
OFF: Driver side rear door locked
-
- OK:
- On the intelligent tester screen, the display changes between ON and OFF as shown in the chart above.
for RHD
Main Body Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
PR Door Lock Position SW
Passenger side rear door lock position switch signal / ON or OFF
ON: Passenger side rear door unlocked
OFF: Passenger side rear door locked
-
- OK:
- On the intelligent tester screen, the display changes between ON and OFF as shown in the chart above.
|
|
||||
| OK | |
| 3. READ VALUE USING INTELLIGENT TESTER (LOCK SWITCH) |
Using the intelligent tester, read the Data List.
for LHD
Entry & Start Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Dr-Door Trigger Switch
Driver side rear door outside handle lock switch / ON or OFF
ON: Entry lock switch pushed
OFF: Entry lock switch not pushed
-
- OK:
- On tester screen, item changes between ON and OFF according to above chart.
for RHD
Entry & Start Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Pr-Door Trigger Switch
Passenger side rear door outside handle lock switch / ON or OFF
ON: Entry lock switch pushed
OFF: Entry lock switch not pushed
-
- OK:
- On tester screen, item changes between ON and OFF according to above chart.
|
|
||||
| OK | ||
| ||
| 4. CHECK HARNESS AND CONNECTOR (REAR DOOR OUTSIDE HANDLE - DOOR ELECTRICAL KEY OSCILLATOR) |
Disconnect the z28 oscillator connector.

Disconnect the z27 handle connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
z28-9 (TRG-) - z27-1 (TRG-)
Always
Below 1 Ω
z28-9 (TRG-) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 5. CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] - REAR DOOR OUTSIDE HANDLE) |
Disconnect the E30 ECU connector.

Disconnect the z27 handle connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
- for LHD:
Tester Connection
Condition
Specified Condition
E30-25 (TSW3) - z27-3 (TRG+)
Always
Below 1 Ω
E30-25 (TSW3) - Body ground
Always
10 kΩ or higher
- for RHD:
Tester Connection
Condition
Specified Condition
E30-26 (TSW4) - z27-3 (TRG+)
Always
Below 1 Ω
E30-26 (TSW4) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 6. INSPECT REAR DOOR OUTSIDE HANDLE LH |
Measure the resistance according to the value(s) in the table below.

- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
z27-1 (TRG-) - z27-3 (TRG+)
Lock switch not pushed
10 kΩ or higher
Lock switch pushed
Below 1 Ω
|
|
||||
| OK | |
| 7. REPLACE DOOR ELECTRICAL KEY OSCILLATOR |
Replace the door electrical key oscillator (Click here).
| NEXT | |
| 8. CHECK DOOR ELECTRICAL KEY OSCILLATOR (OPERATION) |
Check that the entry function operates normally.
- OK:
- Operates normally.
|
|
||||
| OK | ||
| ||
