2011-2013 Land Cruiser · Service Manual Steering

VGRS System Stops or does not Operate

Circuit diagnosis · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

INSPECTION PROCEDURE

HINT:
This problem may be caused by a malfunction in the vehicle stability control system or steering system.
Make sure that no DTC is output for the skid control ECU or steering control ECU before proceeding with the following procedures.
If a DTC is output for either of these ECUs, first troubleshoot it and then proceed to the troubleshooting below.


1. READ VALUE USING INTELLIGENT TESTER (RECORD OF OVERHEAT)
  1. Use the Data List to check if the record of overheat is functioning properly.

    VGRS 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Motor Overheat Record
    Record of continuous overheat preventive control/Rec or Unrec
    Rec or Unrec
    -
    Result 
    Result
    Proceed to
    "Rec" (Record of motor overheating)
    A
    "Unrec" (No record of motor overheating)
    B

    HINT:
    If "Rec" is displayed, reset the setting to "Unrec". Enter the VGRS menu on the tester, select record clearance, and follow the prompts to set to "Unrec".



B
Go to step 3
A


2. CHECK HEAT PROTECTION FUNCTION FOR STEERING ACTUATOR
  1. Turn the engine switch on (IG) and wait for 30 minutes until the steering actuator cools down.

  1. Start the engine and slowly turn the steering wheel from lock to lock (approximately 90°/sec.) 3 times.

    HINT:
    If turning the steering wheel quickly while driving at low speeds, the steering angle may differ between the left and right, or the steering wheel may become off-center.
    However, this is not a malfunction.

  1. Check the number of turns from lock to lock.

    Result 
    Result
    Proceed to
    3.2 turns
    A
    2.7 turns
    B



B
VGRS SYSTEM IS NORMAL
A


3. CHECK STEERING EFFORT
  1. Start the engine.

  1. Turn the steering wheel.

  1. Measure the steering effort.

    Standard steering effort:
    Below 6.9 N*m (70 kgf*cm, 61 in.*lbf)

    HINT:
    After completing the inspection or repair, attempt to simulate the problem and then perform "Read Value Using Intelligent Tester" above again to reconfirm that the problem does not occur.



NG
GO TO POWER STEERING SYSTEM (PROBLEM SYMPTOMS TABLE) (Click here)
OK


4. CHECK STEERING ACTUATOR
  1. Check for abnormal noise or vibration in the steering actuator.

    OK:
    Neither abnormal noise nor vibration occurs.



NG
GO TO STEERING WHEEL VIBRATES OR ABNORMAL NOISE IS HEARD FROM STEERING WHEEL (Click here)
OK


5. CHECK STEERING CONTROL ECU (POWER SOURCE CIRCUIT)
C149134E14
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    E77-3 (IG) -
    Body ground
    Engine switch on (IG)
    11 to 14 V
    E77-8 (PIG) -
    Body ground

  1. Turn the engine switch off.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E77-7 (PGND) -
    Body ground
    Always
    Below 1 Ω

    Result 
    Result
    Result
    Proceed to
    NG
    A
    OK (for LHD)
    B
    OK (for RHD)
    C



B
REPLACE STEERING CONTROL ECU (Click here)

C
REPLACE STEERING CONTROL ECU (Click here)
A

REPAIR OR REPLACE HARNESS OR CONNECTOR


← Steering Wheel is Off-center or Deviates from Neutral Position (from Sep 2011)VGRS System Stops or does not Operate (from Jan 2012) →