2011-2013 Land Cruiser · Service Manual Engine / Hybrid / EV System

P0365 Camshaft Position Sensor "B" Circuit (Bank 1)

Diagnostic trouble codes · Vehicles built from Jan 2012

Also covers:

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

DESCRIPTION

The exhaust camshaft Variable Valve Timing (VVT) sensor (EV1, 2 signal) consists of a magnet and MRE (Magnetic Resistance Element).
The exhaust camshaft has a sensor plate with 3 teeth on its outer circumference. When the exhaust camshaft rotates, changes occur in the air gaps between the 3 teeth and MRE, which affects the magnet. As a result, the resistance of the MRE material fluctuates. The VVT sensor converts the exhaust camshaft rotation data into pulse signals, uses the pulse signals to determine the camshaft angle, and sends it to the ECM.
DTC Code
DTC Detection Condition
Trouble Area
P0365
P0390
When either condition below is met:
  1. The input voltage to the ECM remains at below 0.3 V or higher than 4.7 V for more than 4 seconds when 2 or more seconds have elapsed after turning the engine switch on (IG) (1 trip detection logic).
  2. No VVT sensor signal is sent to the ECM during cranking (1 trip detection logic).
  1. Open or short in VVT sensor (for exhaust side) circuit
  2. VVT sensor (for exhaust side)
  3. Exhaust camshaft
  4. Jumped tooth of timing chain
  5. ECM
P0367
P0392
The output voltage of the VVT sensor is below 0.3 V for 4 seconds (1 trip detection logic).
  1. Open or short in VVT sensor (for exhaust side) circuit
  2. VVT sensor (for exhaust side)
  3. Exhaust camshaft
  4. Jumped tooth of timing chain
  5. ECM
P0368
P0393
The output voltage of the VVT sensor is higher than 4.7 V for 4 seconds (1 trip detection logic).
  1. Open or short in VVT sensor (for exhaust side) circuit
  2. VVT sensor (for exhaust side)
  3. Exhaust camshaft
  4. Jumped tooth of timing chain
  5. ECM

  1. A149747E02
    Reference: Inspection using an oscilloscope.

    Standard:
    Tester Connection
    Tool Setting
    Condition
    Specified Condition
    C45-110 (NE+) - C45-111 (NE-)
    5 V/DIV.
    20 msec./DIV.
    Cranking or idling
    The correct waveform is as shown
    C45-69 (EV1+) - C45-68 (EV1-)
    5 V/DIV.
    20 msec./DIV.
    Cranking or idling
    The correct waveform is as shown
    C45-64 (EV2+) - C45-65 (EV2-)
    5 V/DIV.
    20 msec./DIV.
    Cranking or idling
    The correct waveform is as shown

    HINT:
    EV1+ and EV2+ stand for the VVT sensor (for exhaust side) signal, and NE+ stands for the CKP sensor signal.


MONITOR DESCRIPTION

If no signal is transmitted by the VVT sensor despite the engine revolving, or the rotations of the camshaft and the crankshaft are not synchronized, the ECM interprets this as a malfunction of the sensor.

WIRING DIAGRAM

A179606E08

INSPECTION PROCEDURE

HINT:
  1. Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
  2. Bank 1 refers to the bank that includes the No. 1 cylinder*.
    *: The No. 1 cylinder is the cylinder which is farthest from the transmission.
  3. Bank 2 refers to the bank that does not include the No. 1 cylinder.


1. CHECK HARNESS AND CONNECTOR (SENSOR POWER SOURCE)

  1. A241171E01
    Disconnect the C121 or C122 VVT sensor (for exhaust side) connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    C121-3 (VC2) - Body ground
    Engine switch on (IG)
    4.5 to 5.0 V
    C122-3 (VC2) - Body ground
    Engine switch on (IG)
    4.5 to 5.0 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2. CHECK HARNESS AND CONNECTOR (VVT SENSOR (for Exhaust Side) - ECM)
  1. Disconnect the C121 or C122 VVT (for exhaust side) sensor connector.

  1. Disconnect the C45 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    C121-1 (EX+) - C45-69 (EV1+)
    Always
    Below 1 Ω
    C121-2 (EX-) - C45-68 (EV1-)
    Always
    Below 1 Ω
    C122-1 (EX+) - C45-64 (EV2+)
    Always
    Below 1 Ω
    C122-2 (EX-) - C45-65 (EV2-)
    Always
    Below 1 Ω
    C121-1 (EX+) or C45-69 (EV1+) - Body ground
    Always
    10 kΩ or higher
    C121-2 (EX-) or C45-68 (EV1-) - Body ground
    Always
    10 kΩ or higher
    C122-1 (EX+) or C45-64 (EV2+) - Body ground
    Always
    10 kΩ or higher
    C122-2 (EX-) or C45-65 (EV2-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. CHECK SENSOR INSTALLATION

  1. BR03795E70
    Check the VVT sensor (for exhaust side) installation.

    OK:
    Sensor is installed correctly.



NG
SECURELY REINSTALL SENSOR (Click here)
OK


4. CHECK EXHAUST CAMSHAFT
  1. Check the teeth of the camshaft.

    OK:
    Teeth do not have any cracks or deformation.



NG
REPLACE EXHAUST CAMSHAFT (Click here)
OK


5. REPLACE VVT SENSOR (for Exhaust Side)
  1. Replace the VVT sensor (for exhaust side) (Click here).


NEXT


6. CHECK WHETHER DTC OUTPUT RECURS
  1. Connect the intelligent tester to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the tester on.

  1. Clear DTCs (Click here).

  1. Start the engine.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read DTCs.

    Result 
    Result
    Proceed to
    No output
    A
    P0365, P0367, P0368, P0390, P0392 or P0393
    B

    HINT:
    If the engine does not start, replace the ECM.



B
REPLACE ECM (Click here)
A

END


← P0365 Camshaft Position Sensor "B" Circuit (Bank 1) (+ 5 more codes) (Sep 2011 – Dec 2011)P0443 Evaporative Emission Control System Purge Control Valve Circuit (Sep 2011 – Dec 2011) →