2011-2013 Land Cruiser · Service Manual Vehicle Interior

B1653/35 Seat Position Airbag Sensor Circuit Malfunction

Diagnostic trouble codes · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

DESCRIPTION

The seat position sensor circuit consists of the center airbag sensor and the seat position sensor.
DTC B1653/35 is stored when a malfunction is detected in the seat position sensor circuit.
for LHD 
DTC Code
DTC Detection Condition
Trouble Area
B1653/35
When one of the following conditions is met:
  1. The center airbag sensor receives a line short circuit signal, an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the seat position sensor circuit for 2 seconds.
  2. A seat position sensor malfunction.
  3. A center airbag sensor malfunction.
  1. Floor wire
  2. Seat position sensor
  3. Center airbag sensor assembly
for RHD 
DTC Code
DTC Detection Condition
Trouble Area
B1653/35
When one of the following conditions is met:
  1. The center airbag sensor receives a line short circuit signal, an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the seat position sensor circuit for 2 seconds.
  2. A seat position sensor malfunction.
  3. A center airbag sensor malfunction.
  1. No. 2 floor wire
  2. Seat position sensor
  3. Center airbag sensor assembly

WIRING DIAGRAM

C149681E13
C174604E05
C149681E14
C174604E06

INSPECTION PROCEDURE

NOTICE:
When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected (Click here).


1. CHECK VEHICLE CONDITION
  1. Check vehicle condition.

    Result 
    Result
    Proceed to
    for LHD
    A
    for RHD
    B



B
Go to step 9
A


2. CHECK FOR DTC

  1. C174605E03
    Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1653 is not output.

    HINT:
    Codes other than DTC B1653 may be output at this time, but they are not related to this check.



NG
Go to step 3
OK

USE SIMULATION METHOD TO CHECK (Click here)

3. CHECK CONNECTION OF CONNECTORS
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Check that the connectors are properly connected to the center airbag sensor and the seat position sensor.

    OK:
    The connectors are properly connected.



NG
CONNECT CONNECTORS PROPERLY
OK


4. CHECK CONNECTORS
  1. Disconnect the connectors from the center airbag sensor and the seat position sensor.

  1. Check that the connectors (on the center airbag sensor side and seat position sensor side) are not damaged.

    OK:
    The connectors are not deformed or damaged.



NG
REPLACE FLOOR WIRE
OK


5. CHECK FLOOR WIRE (CENTER AIRBAG SENSOR - SEAT POSITION SENSOR)

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.C174606E05

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    K10-4 (LSP+) - Body ground
    Ignition switch ON
    Below 1 V
    K10-8 (LSP-) - Body ground
    Ignition switch ON
    Below 1 V

  1. w/ Side Airbag:

    1. Turn the ignition switch off.

    2. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      K10-4 (LSP+) - K27-9 (LSP+)
      Always
      Below 1 Ω
      K10-4 (LSP+) - Body ground
      Always
      1 MΩ or higher
      K10-8 (LSP-) - Body ground
      Always
      Below 1 Ω

  1. w/o Side Airbag:

    1. Turn the ignition switch off.

    2. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

    3. Using a service wire, connect terminals 14 (LSP+) and 13 (LSP-) of connector B.

      NOTICE:
      Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.

    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      K10-4 (LSP+) - K10-8 (LSP-)
      Always
      Below 1 Ω

    5. Disconnect the service wire from connector B.

    6. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      K10-4 (LSP+) - K10-8 (LSP-)
      Always
      1 MΩ or higher
      K10-4 (LSP+) - Body ground
      Always
      1 MΩ or higher
      K10-8 (LSP-) - Body ground
      Always
      1 MΩ or higher



NG
REPLACE FLOOR WIRE
OK


6. CHECK SEAT POSITION SENSOR (FRONT SEAT INNER BELT LH)

  1. C174605E03
    Connect the connectors to the center airbag sensor and the seat position sensor.

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs stored in the memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1653 is not output.

    HINT:
    Codes other than DTC B1653 may be output at this time, but they are not related to this check.



NG
Go to step 7
OK

USE SIMULATION METHOD TO CHECK (Click here)

7. REPLACE SEAT POSITION SENSOR (FRONT SEAT INNER BELT LH)
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Replace the front seat inner belt LH (Click here).

    HINT:
    Perform the inspection using parts from a normally functioning vehicle if possible.


NEXT


8. CHECK CENTER AIRBAG SENSOR

  1. C174605E03
    Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1653 is not output.

    HINT:
    Codes other than DTC B1653 may be output at this time, but they are not related to this check.



NG
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)
OK

REPLACE FRONT SEAT INNER BELT ASSEMBLY LH (Click here)

9. CHECK FOR DTC

  1. C146230E15
    Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1653/35 is not output.

    HINT:
    Codes other than DTC B1653/35 may be output at this time, but they are not related to this check.



NG
Go to step 10
OK

USE SIMULATION METHOD TO CHECK (Click here)

10. CHECK CONNECTION OF CONNECTORS
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Check that the connectors are properly connected to the center airbag sensor and the seat position sensor.

    OK:
    The connectors are properly connected.



NG
CONNECT CONNECTORS PROPERLY
OK


11. CHECK CONNECTORS
  1. Disconnect the connectors from the center airbag sensor and the seat position sensor.

  1. Check that the connectors (on the center airbag sensor side and seat position sensor side) are not damaged.

    OK:
    The connectors are not deformed or damaged.



NG
REPLACE NO. 2 FLOOR WIRE
OK


12. CHECK NO. 2 FLOOR WIRE (CENTER AIRBAG SENSOR - SEAT POSITION SENSOR)

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.C174607E06

  1. Measure the voltage according the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    L33-4 (RSP+) - Body ground
    Ignition switch ON
    Below 1 V
    L33-8 (RSP-) - Body ground
    Ignition switch ON
    Below 1 V

  1. w/ Side Airbag:

    1. Turn the ignition switch off.

    2. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      L33-4 (RSP+) - L27-16 (RSP+)
      Always
      Below 1 Ω
      L33-4 (RSP+) - Body ground
      Always
      1 MΩ or higher
      L33-8 (RSP-) - Body ground
      Always
      Below 1 Ω

  1. w/o Side Airbag:

    1. Turn the ignition switch off.

    2. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

    3. Using a service wire, connect terminals 12 (RSP+) and 13 (RSP-) of connector B.

      NOTICE:
      Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.

    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      L33-4 (RSP+) - L33-8 (RSP-)
      Always
      Below 1 Ω

    5. Disconnect the service wire from connector B.

    6. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      L33-4 (RSP+) - Body ground
      Always
      1 MΩ or higher
      L33-8 (RLSP-) - Body ground
      Always
      Below 1 Ω



NG
REPLACE NO. 2 FLOOR WIRE
OK


13. CHECK SEAT POSITION SENSOR (FRONT SEAT INNER BELT RH)

  1. C146230E15
    Connect the connectors to the center airbag sensor and the seat position sensor.

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs stored (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1653/35 is not output.

    HINT:
    Codes other than DTC B1653/35 may be output at this time, but they are not related to this check.



NG
Go to step 14
OK

USE SIMULATION METHOD TO CHECK (Click here)

14. REPLACE SEAT POSITION SENSOR
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Replace the seat position sensor (Click here).

    HINT:
    Perform inspection using parts from a normal vehicle if possible.


NEXT


15. CHECK CENTER AIRBAG SENSOR

  1. C146230E15
    Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1653/35 is not output.

    HINT:
    Codes other than DTC B1653/35 may be output at this time, but they are not related to this check.



NG
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)
OK

REPLACE FRONT SEAT INNER BELT ASSEMBLY RH


← B1651/33 Manual Cut off Switch Trouble (from Jan 2012)B1653/35 Seat Position Airbag Sensor Circuit Malfunction (from Jan 2012) →