2011-2013 Land Cruiser · Service Manual Vehicle Interior

B1860/64 Short in Driver Side Knee Airbag Squib Circuit

Diagnostic trouble codes · Vehicles built Sep 2011 – Dec 2011

Also covers:

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

DESCRIPTION

The driver side knee airbag squib circuit consists of the center airbag sensor and the driver side knee airbag.
This circuit instructs the SRS to deploy when deployment conditions are met.
These DTCs are stored when a malfunction is detected in the driver side knee airbag squib circuit.
DTC Code
DTC Detection Condition
Trouble Area
B1860/64
When one of the following conditions is met:
  1. The center airbag sensor receives a line short circuit signal 5 times in the driver side knee airbag squib circuit during the primary check.
  2. A driver side knee airbag squib malfunction.
  3. A center airbag sensor malfunction.
  1. Instrument panel wire
  2. Driver side knee airbag assembly (Driver side knee squib)
  3. Center airbag sensor assembly
B1861/64
When one of the following conditions is met:
  1. The center airbag sensor receives an open circuit signal in the driver side knee airbag squib circuit for 2 seconds.
  2. A driver side knee airbag squib malfunction.
  3. A center airbag sensor malfunction.
  1. Instrument panel wire
  2. Driver side knee airbag assembly (Driver side knee squib)
  3. Center airbag sensor assembly
B1862/64
When one of the following conditions is met:
  1. The airbag sensor center receives a short circuit to ground signal in the knee airbag (Driver side squib) circuit for 0.5 seconds.
  2. A driver side knee airbag squib malfunction.
  3. A center airbag sensor malfunction.
  1. Instrument panel wire
  2. Driver side knee airbag assembly (Driver side knee squib)
  3. Center airbag sensor assembly
B1863/64
When one of the following conditions is met:
  1. The airbag sensor center receives a short circuit to B+ signal in the knee airbag (Driver side squib) circuit for 0.5 seconds.
  2. A driver side knee airbag squib malfunction.
  3. A center airbag sensor malfunction.
  1. Instrument panel wire
  2. Driver side knee airbag assembly (Driver side knee squib)
  3. Center airbag sensor assembly

HINT:
Vehicles that are not equipped with knee airbag still contain knee airbag circuits and use substitution parts in replace of the knee airbag. If a malfunction occurs in this knee airbag circuit, DTC B1860/64, B1861/64, B1862/64 or B1863/64 is stored.


WIRING DIAGRAM

C146265E07

INSPECTION PROCEDURE

NOTICE:
When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected (Click here).

HINT:
To perform the simulation method, enter the check mode (signal check) with the intelligent tester (Click here), and then wiggle each connector of the airbag system or drive the vehicle on various type of road (Click here).


1. CHECK DRIVER SIDE KNEE AIRBAG (DRIVER SIDE KNEE SQUIB)

  1. C146266E10
    Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Disconnect the connector from the driver side knee airbag.

  1. Connect the white wire side of SST (resistance: 2.1 Ω) to connector C.

    CAUTION:
    Never connect the tester to the driver side knee airbag (driver side knee squib) for measurement, as this may lead to a serious injury due to airbag deployment.

    NOTICE:
    1. Do not forcibly insert SST into the terminals of the connector when connecting SST.
    2. Insert SST straight into the terminals of the connector.

SST
09843-18061  
  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1860, B1861, B1862 or B1863 is not output.

    HINT:
    Codes other than DTC B1860, B1861, B1862 and B1863 may be output at this time, but they are not related to this check.



NG
Go to step 2
OK

REPLACE DRIVER SIDE KNEE AIRBAG ASSEMBLY (Click here)

2. CHECK CONNECTOR
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Disconnect SST from connector C.

  1. Check that the instrument panel wire connector (on the driver side knee airbag side) is not damaged.

    OK:
    The lock button is not disengaged, and the claw of the lock is not deformed or damaged.



NG
REPLACE INSTRUMENT PANEL WIRE
OK


3. CHECK INSTRUMENT PANEL WIRE (DRIVER SIDE KNEE AIRBAG CIRCUIT)

  1. C146267E11
    Disconnect the connectors from the center airbag sensor.

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    E24-1 (DK+) - Body ground
    Ignition switch ON
    Below 1 V
    E24-2 (DK-) - Body ground
    Ignition switch ON
    Below 1 V

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E24-1 (DK+) - E24-2 (DK-)
    Always
    Below 1 Ω

  1. Release the activation prevention mechanism built into connector B (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E24-1 (DK+) - E24-2 (DK-)
    Always
    1 MΩ or higher
    E24-1 (DK+) - Body ground
    Always
    1 MΩ or higher
    E24-2 (DK-) - Body ground
    Always
    1 MΩ or higher



NG
REPLACE INSTRUMENT PANEL WIRE
OK


4. CHECK CENTER AIRBAG SENSOR

  1. C146268E01
    Connect the connectors to the driver side knee airbag and the center airbag sensor.

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1860, B1861, B1862 or B1863 is not output.

    HINT:
    Codes other than DTC B1860, B1861, B1862 and B1863 may be output at this time, but they are not related to this check.



NG
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)
OK

USE SIMULATION METHOD TO CHECK (Click here)


← B1855/63 Short in Rear Side Squib LH Circuit (+ B1856/63, B1857/63, B1858/63) (from Jan 2012)B1860/64 Short in Driver Side Knee Airbag Squib Circuit (+ B1861/64, B1862/64, B1863/64) (from Jan 2012) →