2011-2013 Land Cruiser · Service Manual Engine / Hybrid / EV System

Fuel Injector Circuit

Circuit diagnosis · Vehicles built from Jan 2012

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

DESCRIPTION

The fuel injector assemblies are located on the intake manifold. They inject fuel into the cylinders based on the signals from the ECM.

WIRING DIAGRAM

A264510E02

INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.


1. CHECK FUEL INJECTOR ASSEMBLY (POWER SOURCE)

  1. A208644E26
    Disconnect the fuel injector assembly connector.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Cylinder
    Tester Connection
    Switch Condition
    Specified Condition
    No. 1
    C5-1 - Body ground
    Ignition switch ON
    11 to 14 V
    No. 2
    C16-1 - Body ground
    Ignition switch ON
    11 to 14 V
    No. 3
    C7-1 - Body ground
    Ignition switch ON
    11 to 14 V
    No. 4
    C14-1 - Body ground
    Ignition switch ON
    11 to 14 V
    No. 5
    C9-1 - Body ground
    Ignition switch ON
    11 to 14 V
    No. 6
    C12-1 - Body ground
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Fuel Injector Assembly)

  1. Turn the ignition switch off.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (INTEGRATION RELAY (IG2) - FUEL INJECTOR ASSEMBLY)
OK


2. INSPECT FUEL INJECTOR ASSEMBLY
  1. Inspect the fuel injector assembly (Click here).



NG
REPLACE FUEL INJECTOR ASSEMBLY (Click here)
OK


3. CHECK HARNESS AND CONNECTOR (FUEL INJECTOR ASSEMBLY - ECM)
  1. Disconnect the fuel injector assembly connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LHD 
    Cylinder
    Tester Connection
    Condition
    Specified Condition
    No. 1
    C5-2 - Body ground
    Always
    10 kΩ or higher
    C5-2 - C45-86 (#10)
    Always
    Below 1 Ω
    No. 2
    C16-2 - Body ground
    Always
    10 kΩ or higher
    C16-2 - C45-109 (#20)
    Always
    Below 1 Ω
    No. 3
    C7-2 - Body ground
    Always
    10 kΩ or higher
    C7-2 - C45-85 (#30)
    Always
    Below 1 Ω
    No. 4
    C14-2 - Body ground
    Always
    10 kΩ or higher
    C14-2 - C45-108 (#40)
    Always
    Below 1 Ω
    No. 5
    C9-2 - Body ground
    Always
    10 kΩ or higher
    C9-2 - C45-84 (#50)
    Always
    Below 1 Ω
    No. 6
    C12-2 - Body ground
    Always
    10 kΩ or higher
    C12-2 - C45-107 (#60)
    Always
    Below 1 Ω
    for RHD 
    Cylinder
    Tester Connection
    Condition
    Specified Condition
    No. 1
    C5-2 - Body ground
    Always
    10 kΩ or higher
    C5-2 - C46-86 (#10)
    Always
    Below 1 Ω
    No. 2
    C16-2 - Body ground
    Always
    10 kΩ or higher
    C16-2 - C46-109 (#20)
    Always
    Below 1 Ω
    No. 3
    C7-2 - Body ground
    Always
    10 kΩ or higher
    C7-2 - C46-85 (#30)
    Always
    Below 1 Ω
    No. 4
    C14-2 - Body ground
    Always
    10 kΩ or higher
    C14-2 - C46-108 (#40)
    Always
    Below 1 Ω
    No. 5
    C9-2 - Body ground
    Always
    10 kΩ or higher
    C9-2 - C46-84 (#50)
    Always
    Below 1 Ω
    No. 6
    C12-2 - Body ground
    Always
    10 kΩ or higher
    C12-2 - C46-107 (#60)
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)


← Fuel Injector Circuit (Sep 2011 – Dec 2011)Starter Signal Circuit (Sep 2011 – Dec 2011) →