B1865/65 Short in Front Passenger Side Knee Airbag Squib Circuit
Diagnostic trouble codes · Vehicles built Sep 2011 – Dec 2011
Also covers:
- B1866/65 Open in Front Passenger Side Knee Airbag Squib Circuit
- B1867/65 Short to GND in Front Passenger Side Knee Airbag Squib Circuit
- B1868/65 Short to B+ in Front Passenger Side Knee Airbag Squib Circuit
Versions by build date: Sep 2011 – Dec 2011 from Jan 2012
DESCRIPTION
The front passenger side knee airbag squib circuit consists of the center airbag sensor and the front passenger side knee airbag.The circuit instructs the SRS to deploy when deployment conditions are met.
These DTCs are stored when a malfunction is detected in the front passenger side knee airbag squib circuit.
| DTC Code |
DTC Detection Condition |
Trouble Area |
| B1865/65 |
When one of the following conditions is met:
|
|
| B1866/65 |
When one of the following conditions is met:
|
|
| B1867/65 |
When one of the following conditions is met:
|
|
| B1868/65 |
When one of the following conditions is met:
|
|
- HINT:
- Vehicles that are not equipped with knee airbag still contain knee airbag circuits and use substitution parts in replace of the knee airbag. If a malfunction occurs in this knee airbag circuit, DTC B1865/65, B1866/65, B1867/65 or B1868/65 is stored.
WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected (Click here).
- HINT:
- To perform the simulation method, enter the check mode (signal check) with the intelligent tester (Click here), and then wiggle each connector of the airbag system or drive the vehicle on various type of road (Click here).
| 1. CHECK FRONT PASSENGER SIDE KNEE AIRBAG (FRONT PASSENGER SIDE KNEE SQUIB) |
Turn the ignition switch off.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Disconnect the connector from the front passenger side knee airbag.
Connect the white wire side of SST (resistance: 2.1 Ω) to connector C.
- CAUTION:
- Never connect the tester to the front passenger side knee airbag (front passenger side knee squib) for measurement, as this may lead to a serious injury due to airbag deployment.
- NOTICE:
- Do not forcibly insert SST into the terminals of the connector when connecting SST.
- Insert SST straight into the terminals of the connector.
- Do not forcibly insert SST into the terminals of the connector when connecting SST.
- SST
- 09843-18061
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs (Click here).
- OK:
- DTC B1865, B1866, B1867 or B1868 is not output.
- HINT:
- Codes other than DTC B1865, B1866, B1867 and B1868 may be output at this time, but they are not related to this check.
|
|
||||
| OK | ||
| ||
| 2. CHECK CONNECTOR |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Disconnect SST from connector C.
Check that the instrument panel wire connector (on the front passenger side knee airbag side) is not damaged.
- OK:
- The lock button is not disengaged, and the claw of the lock is not deformed or damaged.
|
|
||||
| OK | |
| 3. CHECK INSTRUMENT PANEL WIRE (FRONT PASSENGER KNEE SQUIB CIRCUIT) |
Disconnect the connectors from the center airbag sensor.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
E40-1 (PK+) - Body ground
Ignition switch ON
Below 1 V
E40-2 (PK-) - Body ground
Ignition switch ON
Below 1 V
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
E40-1 (PK+) - E40-2 (PK-)
Always
Below 1 Ω
Release the activation prevention mechanism built into connector B (Click here).
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
E40-1 (PK+) - E40-2 (PK-)
Always
1 MΩ or higher
E40-1 (PK+) - Body ground
Always
1 MΩ or higher
E40-2 (PK-) - Body ground
Always
1 MΩ or higher
|
|
||||
| OK | |
| 4. CHECK CENTER AIRBAG SENSOR |
Connect the connectors to the front passenger side knee airbag and the center airbag sensor.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs (Click here).
- OK:
- DTC B1865, B1866, B1867 or B1868 is not output.
- HINT:
- Codes other than DTC B1865, B1866, B1867 and B1868 may be output at this time, but they are not related to this check.
|
|
||||
| OK | ||
| ||
