2011-2013 Land Cruiser · Service Manual Audio / Visual / Telematics

DTC CHECK / CLEAR

Troubleshooting · Vehicles built from Jan 2012


CHECK DTC (CHECK USING INTELLIGENT TESTER)
  1. Connect the intelligent tester to the DLC3.

  2. Turn the engine switch on (IG).

  3. Turn the intelligent tester on.

  4. Enter the following menus: Body / Navigation System / DTCs.

  5. Check for DTCs, and then write them down.

  6. Check the details of the DTC(s) (Click here).

    NOTICE:
    The navigation system outputs DTCs for the following system. When DTCs other than those in Diagnostic Trouble Code Chart for the navigation system are output, refer to Diagnostic Trouble Code Chart for the relevant system.
    System
    Proceed to
    Audio and Visual System (w/ Navigation System)
    Click here
    Rear Seat Entertainment System
    Click here


CLEAR DTC (CHECK USING INTELLIGENT TESTER)
  1. Connect the intelligent tester to the DLC3.

  2. Turn the engine switch on (IG).

  3. Turn the intelligent tester on.

  4. Enter the following menus: Body / Navigation System / DTCs.

  5. Clear the DTCs.


START DIAGNOSTIC MODE

HINT:
  1. Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.
  2. To help find the malfunction when the system cannot change to diagnostic mode, check for DTCs using the intelligent tester.
  3. After the engine switch is turned on (IG), check that the map is displayed before starting diagnostic mode. Otherwise, some items cannot be checked.

  1. E196428E04
    Start the engine.
    Text in Illustration 
    *A
    for LHD
    *B
    for RHD
    *a
    "INFO" Switch

  2. While pressing and holding the "INFO" switch, operate the light control switch: Off → Tail → Off → Tail → Off → Tail → Off.

  3. Diagnostic mode starts and the "Service Menu" screen will be displayed.


FINISH DIAGNOSTIC MODE
  1. There are 2 methods to finish diagnostic mode. Start the mode by using one of them.

  2. Method 1

    1. Turn the engine switch off.

  3. Method 2

    1. Press and hold the "SETUP" switch for 3 seconds or more.


FAILURE DIAGNOSIS

  1. E245677
    Press the "Failure Diagnosis" switch on the "Service Menu" screen.

  2. E245678
    The "Failure Diagnosis" will be displayed.


SYSTEM CHECK

  1. E245679
    Press the "System Check" switch on the "Failure Diagnosis" screen.

  2. E251475
    The "System Check Mode" screen will be displayed.


CHECK DTC (CHECK USING SYSTEM CHECK MODE SCREEN)

  1. E251475E01
    System check mode screen description
    Screen Description 
    Display
    Content
    *a: Node position number for devices that use MOST communication
    MOST node position numbers are provided for devices connected to the MOST network.
    *b: Device Name List No. 1
    1. Device Name List No. 1 displays some of the devices that make up the audio and visual system.
    2. The names of the components from Device Name List No. 1 are shown in the following table.
    *c: Check Result
    Result codes for all devices are displayed.
    *d: Memory Clear
    1. Present and history DTCs and registered connected device names are cleared.
    2. Press the "Memory CLR" switch for 3 seconds.
    *e: Recheck
    1. A system check will be performed again after the memory is cleared.
    2. The "Recheck" switch will dim during a system check.
    *f: Device Name List No. 2
    1. Device Name List No. 2 displays some of the devices that make up the audio and visual system.
    2. The names of the components from Device Name List No. 2 are shown in the following table.
    *b: Device Name List No. 1 Description 
    Name
    Component
    Connection Method
    EMV-M
    Multi-media module receiver assembly
    -
    AMP
    Stereo component amplifier assembly
    Communication line for MOST
    RSE
    Television display assembly
    Communication line for MOST
    DISP
    Multi-display assembly
    Communication line for AVC-LAN
    CAMERA-C
    Parking assist ECU
    Communication line for AVC-LAN
    *c: Check Result Description 
    Result
    Meaning
    Action
    OK
    The device does not respond with a DTC.
    -
    MOST
    MOST communication error
    Perform "MOST Line Check" to check connection of each device on the MOST network.
    DETAIL
    The device responds with a DTC.
    Look up the DTC in "Unit Check Mode".
    NCON
    The device was previously present, but does not respond in diagnostic mode.
    1. Check power supply wire harness of the device.
    2. Check the AVC-LAN of the device.
    NRES
    The device responds in diagnostic mode, but gives no DTC information.
    1. Check power supply wire harness of the device.
    2. Check the AVC-LAN of the device.
    *f: Device Name List No. 2 Description 
    Name
    Component
    Connection Method
    VTR/FR
    Headphone terminal
    Vehicle wire harness
    AUX
    No. 1 stereo jack adapter assembly
    Vehicle wire harness

  2. E246895E01
    Unit check mode screen description
    Screen Description 
    Display
    Content
    *a: Device name
    Target device
    *b: History DTC
    Diagnostic memory results and stored DTCs are displayed.
    *c: Current DTC
    DTCs output in the service check are displayed.
    *d: DTC
    DTC (Diagnostic Trouble Code)
    *e: Diagnosis clear switch
    Pushing this switch for 3 seconds clears the diagnostic memory data of the target device. (Both response to diagnostic system check result and the displayed data are cleared.)

    HINT:
    1. This screen is updated once per second.
    2. A maximum of 6 DTCs can be displayed for history and present DTCs.

  3. Read the system check result.

    1. E251475E03
      If the check result is "DETAIL", touch the displayed check result

      HINT:
      When all results are "OK", this means that no DTCs are stored.

    2. E246895
      View the results on the "Unit Check Mode" screen and record them.

      NOTICE:
      A maximum of 6 DTCs can be displayed for history and present DTCs on the "Unit check mode" screen. Therefore, when 6 DTCs are displayed, troubleshoot those DTCs first and then check the "Unit check mode" screen again to see if any other DTCs are displayed.

    3. E246895E02
      When proceeding to view the results of another device, press the "Back" switch to return to the "System Check Mode" screen. Repeat the step above to view the results of other devices.

      HINT:
      To check other item, repeat from the first step.

    4. Check the details of the DTC(s) (Click here).

      NOTICE:
      The navigation system outputs DTCs for the following system. When DTCs other than the codes in Diagnostic Trouble Code Chart for the navigation system are output, refer to Diagnostic Trouble Code Chart for the relevant system.
      System
      Proceed to
      Audio and Visual System (w/ Navigation System)
      Click here
      Rear Seat Entertainment System
      Click here


DTC CLEAR/RECHECK (CLEAR USING SYSTEM CHECK MODE SCREEN)

  1. Clear DTC

    1. E251475E08
      Press the "Memory CLR" switch for 3 seconds.

    2. Confirm that the check results are cleared.

      HINT:
      1. To clear the DTC for a specific device, clear the DTC using the "Unit Check Mode" screen.
      2. When clearing a DTC using the "Unit Check Mode" screen, press the "Code CLR" switch for 3 seconds.

  2. E251475E09
    Recheck DTC

    1. Press the "Recheck" switch.

    2. E251475E10
      Confirm that all diagnostic codes are "OK" when the check results are displayed. If a code other than "OK" is displayed, troubleshoot again.

      HINT:
      When a DTC was cleared using the "Unit Check Mode" screen, press the "Back" switch to return to the "System Check Mode" screen and perform this operation.

← TERMINALS OF ECU (from Jan 2012)FREEZE FRAME DATA (from Jan 2012) →