2011-2013 Land Cruiser · Service Manual Drivetrain

P0818 Driveline Disconnect Switch Input Circuit

Diagnostic trouble codes · Vehicles built Sep 2011 – Dec 2011

DESCRIPTION

The ECM detects the signal indicating that the transfer is in neutral.
This DTC indicates that the signal indicating that the transfer is in neutral remains on.
DTC Code
DTC Detection Condition
Trouble Area
P0818
The signal indicating that the transfer is in neutral remains on while the vehicle is running under the following conditions for 30 sec. (2 trip detection logic):
  1. The vehicle speed is 25 km/h (16 mph) or more.
  2. The transfer position switch is in H4.
  1. Short in transfer neutral signal
  2. Transfer shift actuator assembly (transfer system)
  3. ECM

MONITOR DESCRIPTION

The ECM detects whether or not the transfer is in neutral by monitoring the signal from the transfer shift actuator assembly.
If the ECM detects that the transfer is in neutral under the following conditions, the ECM will conclude that there is a malfunction of the transfer shift actuator assembly, illuminate the MIL and store the DTC:
  1. The transfer shift actuator assembly indicates that the transfer is in neutral.
  2. The transfer position switch is in the H4 position.
  3. The vehicle is being driven at 25 km/h (16 mph) or more.
  4. The transfer neutral signal has been on for more than 30 seconds.

WIRING DIAGRAM

C179559E01

INSPECTION PROCEDURE


1. CHECK HARNESS AND CONNECTOR (TRANSFER SHIFT ACTUATOR ASSEMBLY - BODY GROUND)

  1. C159074E09
    Disconnect the C38 transfer shift actuator assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    C38-3 (N) - Body ground
    Always
    10 kΩ or higher



NG
Go to step 2
OK

GO TO TRANSFER SYSTEM INSPECTION (Click here)

2. CHECK HARNESS AND CONNECTOR (FOUR WHEEL DRIVE CONTROL ECU - BODY GROUND)
C162221E09
  1. Disconnect the A27 four wheel drive control ECU connector.

  1. Disconnect the C38 transfer shift actuator assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A27-16 (NP) - Body ground
    Always
    10 kΩ or higher



NG
Go to step 3
OK

GO TO TRANSFER SYSTEM INSPECTION (Click here)

3. CHECK HARNESS AND CONNECTOR (TRANSFER SHIFT ACTUATOR ASSEMBLY, FOUR WHEEL DRIVE CONTROL ECU - ECM)
C177782E03
  1. Disconnect the A38 ECM connector (for LHD).

  1. Disconnect the A52 ECM connector (for RHD).

  1. Disconnect the C38 transfer shift actuator assembly connector.

  1. Disconnect the A27 four wheel drive control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LHD 
    Tester Connection
    Condition
    Specified Condition
    A38-5 (TFN) - Body ground
    Always
    10 kΩ or higher
    for RHD 
    Tester Connection
    Condition
    Specified Condition
    A52-5 (TFN) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)


← P0781 1-2 Shift (1-2 Shift Valve) (Sep 2011 – Dec 2011)P0894 Transmission Component Slipping (+ P2714) (Sep 2011 – Dec 2011) →