2011-2013 Land Cruiser · Service Manual Drivetrain

DISASSEMBLY

Removal / installation · Vehicles built from Jan 2012

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012


1. REMOVE TRANSMISSION CONTROL SHAFT LEVER RH

C177425
  1. Remove the nut, spring washer and control shaft lever.


2. REMOVE PARK/NEUTRAL POSITION SWITCH ASSEMBLY

C177426
  1. Using a screwdriver, bend the tabs of the lock washer.

  1. Remove the nut, lock washer and bolt.

  1. Remove the park/neutral position switch.

    HINT:
    Make sure that the manual valve lever shaft has not been rotated prior to installing the park/neutral position switch as the detent spring may become detached from the manual valve lever shaft.


3. REMOVE SPEED SENSOR

C177427
  1. Remove the 2 bolts and 2 speed sensors.

  1. Remove the 2 O-rings from the sensors.


4. REMOVE TRANSMISSION OIL COOLER ASSEMBLY (w/ ATF Warmer)

  1. C175538E03
    Remove the 3 bolts and transmission oil cooler assembly with transmission oil thermostat.
    Text in Illustration 
    *1
    Transmission Oil Cooler Assembly
    *2
    Transmission Oil Thermostat
    *3
    O-ring

  1. Disconnect the transmission oil cooler assembly from the transmission oil thermostat.

  1. Remove the 2 O-rings from the transmission oil cooler assembly.

  1. Remove the 2 O-rings from the transmission oil thermostat.


5. REMOVE OIL COOLER TUBE UNION (w/o ATF Warmer)

C177400
  1. Remove the 2 oil cooler tube unions.

  1. Remove the 2 O-rings from the oil cooler tube unions.


6. REMOVE AUTOMATIC TRANSMISSION BREATHER TUBE

C178810
  1. Remove the 2 bolts.

  1. Remove the breather tube.

  1. Remove the O-ring from the tube.


7. REMOVE AUTOMATIC TRANSMISSION HOUSING

  1. C227169E01
    Remove the 14 bolts.
    Text in Illustration 
    *A
    for 1VD-FTV
    *B
    for 1UR-FE, 3UR-FE

  1. Remove the transmission housing.


8. REMOVE REAR TRANSFER ADAPTER

C162765
  1. Remove the 10 bolts.

  1. Remove the rear transfer adapter.

    HINT:
    Tap on the circumference of the extension housing with a plastic-faced hammer to remove the rear transfer adapter.


9. REMOVE TRANSMISSION CASE ADAPTER OIL SEAL

C162766E01
  1. Using a screwdriver, pry out the oil seal.

    Text in Illustration 
    *1
    Protective Tape

    NOTICE:
    Be careful not to damage the rear transfer adapter.

    HINT:
    Wrap the tip of the screwdriver with tape.


10. REMOVE TRANSFER CASE ADAPTER RADIAL BALL BEARING

C162767E01
  1. Using a screwdriver, remove the snap ring.

  1. Using SST and a press, press out the bearing.

    SST
    09950-60010   (09951-00650)
    09950-70010   (09951-07150)


11. SECURE AUTOMATIC TRANSMISSION CASE SUB-ASSEMBLY

C161613
  1. Install the transmission case to an overhaul attachment.


12. REMOVE AUTOMATIC TRANSMISSION OIL PAN SUB-ASSEMBLY

C178811E01

NOTICE:
Do not turn the transmission over as this will contaminate the valve body with foreign matter from the bottom of the pan.

  1. Remove the drain plug, 12 bolts, oil pan and gasket.

  1. Remove the 4 magnets.


13. INSPECT AUTOMATIC TRANSMISSION OIL PAN SUB-ASSEMBLY

D001124E01
  1. Remove the magnets, and use them to collect steel particles.

  1. Carefully look at the foreign matter and particles in the pan and on the magnets to anticipate the type of wear you will find in the transmission.

    1. Steel (magnetic): bearing, gear and clutch plate wear
    2. Brass (non-magnetic): bush wear


14. REMOVE VALVE BODY OIL STRAINER ASSEMBLY

C178807
  1. Turn over the transmission.

  1. Remove the 4 bolts and oil strainer from the valve body oil strainer assembly.

  1. Remove the O-ring from the valve body oil strainer assembly.


15. REMOVE NO. 1 TRANSMISSION WIRE AND NO. 2 TRANSMISSION WIRE

C161112E01
  1. Remove the 2 bolts and 2 temperature sensor clamps.

  1. Disconnect the 2 ATF temperature sensors.

  1. Disconnect the 9 connectors from the solenoid valves.

  1. C161614
    Remove the 2 bolts and pull the No. 1 and No. 2 transmission wires out of the transmission case.

  1. C161615
    Remove the 2 O-rings from the transmission wires.


16. REMOVE TRANSMISSION VALVE BODY ASSEMBLY
  1. Remove the bolt, detent spring cover and detent spring.

  1. C162147E02
    Remove the 19 bolts.

  1. Remove the valve body assembly.


17. REMOVE TRANSMISSION CASE GASKET

C161616
  1. Remove the 3 gaskets.


18. REMOVE BRAKE DRUM GASKET

C161617
  1. Remove the 3 gaskets.


19. REMOVE CHECK BALL BODY

C161618E02
Text in Illustration 
*1
Check Ball Body
*2
Spring
  1. Remove the check ball body and spring.


20. REMOVE C-2 ACCUMULATOR PISTON

C161619
  1. While applying compressed air to the oil hole, remove the C-2 accumulator piston and spring.

    NOTICE:
    Be careful as the B-3 accumulator pistons may jump out.

  1. Remove the 2 O-rings from the piston.


21. REMOVE B-3 ACCUMULATOR PISTON

C228984
  1. While applying compressed air to the oil hole, remove the B-3 accumulator piston and spring.

  1. Remove the 2 O-rings from the piston.


22. REMOVE C-3 ACCUMULATOR PISTON

C161620
  1. While applying compressed air to the oil hole, remove the C-3 accumulator piston and spring.

  1. Remove the 2 O-rings from the piston.


23. REMOVE B-1 ACCUMULATOR VALVE

C161621
  1. Remove the B-1 accumulator valve and 2 springs.


24. REMOVE PARKING LOCK PAWL BRACKET

C161622
  1. Remove the 3 bolts and bracket.


25. REMOVE PARKING LOCK ROD SUB-ASSEMBLY

C161623E01
  1. Disconnect the parking lock rod from the manual valve lever sub-assembly.


26. REMOVE PARKING LOCK PAWL

C161624E01
  1. Pull out the parking lock pawl shaft from the front side, and then remove the lock pawl and spring.

  1. Remove the E-ring from the shaft.


27. REMOVE MANUAL VALVE LEVER SUB-ASSEMBLY

D027918E01
  1. Using a screwdriver and hammer, cut off the spacer and remove it from the shaft.

  1. C161626
    Using a pin punch and hammer, tap out the spring pin.

    HINT:
    Slowly tap out the spring pin so that it does not fall into the transmission case.

  1. Pull the manual valve lever shaft out through the transmission case and remove the manual valve lever sub-assembly.


28. REMOVE MANUAL VALVE LEVER SHAFT OIL SEAL

C161628E02
  1. Using a screwdriver, pry out the 2 oil seals.

    Text in Illustration 
    *1
    Protective Tape

    NOTICE:
    Be careful not to damage the transmission case.

    HINT:
    Wrap the tip of the screwdriver with protective tape before use.


29. REMOVE OIL PUMP ASSEMBLY

C161629
  1. Remove the 10 bolts.

  1. C161630E01
    Using SST, pull out the oil pump.
    SST
    09950-40011   (09951-04010, 09953-04020, 09958-04011, 09952-04010, 09954-04010, 09955-04031, 09955-04031)

  1. C161631
    Remove the O-ring and 2 thrust bearing races from the oil pump.


30. REMOVE CLUTCH DRUM AND INPUT SHAFT ASSEMBLY

C161632
  1. Remove the clutch drum and input shaft assembly from the transmission case.

  1. C161633
    Remove the clutch drum thrust washer and 2 thrust needle roller bearings.


31. INSPECT NO. 2 1-WAY CLUTCH ASSEMBLY

C161779E01
  1. Hold the reverse clutch hub and turn the 1-way clutch assembly. Check that the 1-way clutch turns freely clockwise and locks when turned counterclockwise.


32. REMOVE NO. 2 1-WAY CLUTCH ASSEMBLY

C161634
  1. Remove the No. 2 1-way clutch and clutch drum thrust washer from the clutch drum and input shaft assembly.


33. SECURE CLUTCH DRUM AND INPUT SHAFT ASSEMBLY

  1. C161636E02
    Place the oil pump onto the torque converter, and then place the clutch drum and input shaft assembly onto the oil pump.
    Text in Illustration 
    *1
    Torque Converter
    *2
    Oil Pump


34. REMOVE REVERSE CLUTCH HUB SUB-ASSEMBLY

C161637
  1. Using a screwdriver, remove the snap ring.

  1. C161638
    Remove the reverse clutch reaction sleeve and reverse clutch hub sub-assembly together with the rear clutch disc set from the clutch drum.


35. REMOVE REAR CLUTCH DISC SET
  1. for 1VD-FTV:
    Remove the cushion plate, reverse clutch flange, 4 discs and 3 plates from the reverse clutch hub.

  1. for 1UR-FE, 3UR-FE
    Remove the cushion plate, reverse clutch flange, 5 discs and 4 plates from the reverse clutch hub.

  1. C162148
    Remove the flange from the clutch drum.

  1. C229006E01
    Using a screwdriver, remove the snap ring.
    Text in Illustration 
    *1
    Protective Tape

    NOTICE:
    Be careful not to damage the clutch drum.

    HINT:
    Wrap the tip of the screwdriver with tape.


36. INSPECT REAR CLUTCH DISC

C162758
  1. Replace all discs if one of the following problems is present: 1) a disc, plate or flange is worn or burnt, 2) the lining of a disc is peeled off or discolored, or 3) grooves have even a little bit of damage.

    NOTICE:
    Before assembling new discs, soak them in ATF for at least 2 hours.


37. INSPECT REVERSE CLUTCH HUB SUB-ASSEMBLY

C161792
  1. Using a dial indicator, measure the inside diameter of the reverse clutch hub bush.

    Standard inside diameter:
    41.912 to 41.937 mm (1.410 to 1.411 in.)

    1. If the inside diameter is more than the standard, replace the reverse clutch hub.


38. REMOVE FORWARD CLUTCH HUB SUB-ASSEMBLY

C161641
  1. Remove the thrust needle roller bearing, forward clutch hub and No. 3 clutch hub thrust washer from the clutch drum.


39. INSPECT FORWARD CLUTCH HUB SUB-ASSEMBLY

C161791
  1. Using a dial indicator, measure the inside diameter of the forward clutch hub bush.

    Standard inside diameter:
    30.200 to 30.225 mm (1.189 to 1.190 in.)

    1. If the inside diameter is more than the standard, replace the forward clutch hub.


40. REMOVE COAST CLUTCH HUB SUB-ASSEMBLY WITH NO. 4 1-WAY CLUTCH ASSEMBLY

C161642
  1. Remove the 2 thrust needle roller bearings, the coast clutch hub with the No. 4 1-way clutch assembly, and the thrust bearing race from the clutch drum.


41. INSPECT NO. 4 1-WAY CLUTCH ASSEMBLY

C161784E01
  1. Hold the coast clutch hub and turn the 1-way clutch assembly. Check that the 1-way clutch turns freely clockwise and locks when turned counterclockwise.


42. REMOVE NO. 4 1-WAY CLUTCH ASSEMBLY

C161643
  1. Separate the No. 4 1-way clutch assembly from the coast clutch hub.

  1. Remove the No. 2 clutch hub thrust washer from the coast clutch hub.


43. REMOVE FORWARD MULTIPLE DISC CLUTCH DISC SET

C228985E01
  1. Using a screwdriver, remove the snap ring.

    Text in Illustration 
    *1
    Protective Tape

    NOTICE:
    Be careful not to damage the forward clutch piston.

    HINT:
    Wrap the tip of the screwdriver with tape.

  1. Remove the flange, 6 discs, 6 plates and cushion plate from the input shaft.


44. INSPECT FORWARD MULTIPLE DISC CLUTCH DISC

C161790
  1. Replace all discs if one of the following problems is present: 1) a disc, plate or flange is worn or burnt, 2) the lining of a disc is peeled off or discolored, or 3) grooves or printed numbers have even a little bit of damage.

    NOTICE:
    Before assembling new discs, soak them in ATF for at least 2 hours.


45. REMOVE COAST CLUTCH DISC SET

C228986E01
  1. Using a screwdriver, remove the snap ring.

    Text in Illustration 
    *1
    Protective Tape

    NOTICE:
    Be careful not to damage the forward clutch piston.

    HINT:
    Wrap the tip of the screwdriver with tape.

  1. for 1VD-FTV:
    Remove the coast clutch flange, 5 discs and 5 plates from the input shaft.

  1. for 1UR-FE, 3UR-FE
    Remove the coast clutch flange, 4 discs and 4 plates from the input shaft.


46. INSPECT COAST CLUTCH DISC

C161789
  1. Replace all discs if one of the following problems is present: 1) a disc, plate or flange is worn or burnt, 2) the lining of a disc is peeled off or discolored, or 3) grooves or printed numbers have even a little bit of damage.

    NOTICE:
    Before assembling new discs, soak them in ATF for at least 2 hours.


47. REMOVE INPUT SHAFT SUB-ASSEMBLY

C161648
  1. Remove the input shaft from the clutch drum.


48. REMOVE INPUT SHAFT OIL SEAL RING

C161649
  1. Remove the 4 oil seal rings from the input shaft.


49. REMOVE COAST CLUTCH PISTON

C161650E01
  1. Place SST on the No. 1 clutch balancer and compress the forward clutch return spring with a press.

    SST
    09350-30020   (09350-07040)

  1. Using SST, remove the snap ring.

    SST
    09350-30020   (09350-07070)

  1. C161651
    Remove the No. 1 clutch balancer and forward clutch return spring from the input shaft.

  1. C161652
    Remove the O-ring from the No. 1 clutch balancer.

  1. C161653
    Hold the input shaft by hand and apply compressed air to the input shaft to remove the coast clutch piston.


50. INSPECT FORWARD CLUTCH RETURN SPRING SUB-ASSEMBLY

C161788
  1. Using a vernier caliper, measure the free length of the spring together with the spring seat.

    Standard free length:
    29.65 mm (1.17 in.)


51. REMOVE FORWARD CLUTCH PISTON SUB-ASSEMBLY

C161654
  1. Hold the input shaft by hand and apply compressed air to the input shaft to remove the forward clutch piston.

  1. C162744
    Remove the O-ring from the input shaft.


52. REMOVE NO. 3 CLUTCH BALANCER

C161656E01
  1. Place SST on the No. 3 clutch balancer and compress the reverse clutch return spring with a press.

    SST
    09380-60010   (09381-06020, 09381-06030, 09381-06040, 09381-06050, 09381-06080)

  1. Using SST, remove the snap ring.

    SST
    09350-30020   (09350-07070)

  1. Remove the No. 3 clutch balancer.

  1. C161657
    Remove the reverse clutch return spring and O-ring from the reverse clutch piston.


53. INSPECT REVERSE CLUTCH RETURN SPRING SUB-ASSEMBLY

C161786
  1. Using a vernier caliper, measure the free length of the spring together with the spring seat.

    Standard free length:
    21.24 mm (0.836 in.)


54. REMOVE REVERSE CLUTCH PISTON SUB-ASSEMBLY

C161700
  1. Remove the reverse clutch piston from the clutch drum.

  1. C161702
    Remove the O-ring from the reverse clutch piston.

  1. C161703
    Remove the O-ring from the clutch drum.


55. REMOVE DIRECT CLUTCH DISC SET

C228987E01
  1. Using a screwdriver, remove the snap rings from the clutch drum.

    Text in Illustration 
    *1
    Protective Tape

    NOTICE:
    Be careful not to damage the clutch drum.

    HINT:
    Wrap the tip of the screwdriver with tape.

  1. for 1VD-FTV:
    Remove the direct clutch flange, 6 discs and 6 plates from the clutch drum.

  1. for 1UR-FE, 3UR-FE
    Remove the direct clutch flange, 5 discs and 5 plates from the clutch drum.


56. INSPECT DIRECT CLUTCH DISC

C161787
  1. Replace all discs if one of the following problems is present: 1) a disc, plate or flange is worn or burnt, 2) the lining of a disc is peeled off or discolored, or 3) grooves or printed numbers have even a little bit of damage.

    NOTICE:
    Before assembling new discs, soak them in ATF for at least 2 hours.


57. REMOVE DIRECT CLUTCH PISTON SUB-ASSEMBLY

C161704E01
  1. Place SST on the direct clutch piston and compress the direct clutch return spring with a press.

    SST
    09380-60010   (09381-06030, 09381-06040, 09381-06080)

  1. Using SST, remove the snap ring.

    SST
    09350-30020   (09350-07070)

  1. Place the oil pump onto the torque converter, and then place the clutch drum onto the oil pump.

  1. C161705E02
    Hold the direct clutch piston by hand and apply compressed air to the oil hole of the oil pump as shown in the illustration to remove the direct clutch piston together with the No. 2 clutch balancer and direct clutch return spring sub-assembly.
    Text in Illustration 
    *1
    Oil Hole

  1. C161706
    Remove the No. 2 clutch balancer and direct clutch return spring sub-assembly from the direct clutch piston.

  1. C161812
    Remove the 2 O-rings from the direct clutch piston.


58. INSPECT DIRECT CLUTCH RETURN SPRING SUB-ASSEMBLY

C161785
  1. Using a vernier caliper, measure the free length of the spring together with the spring seat.

    Standard free length:
    19.46 mm (0.766 in.)


59. REMOVE NO. 3 BRAKE SNAP RING

C228989E01
  1. Using a screwdriver, remove the No. 3 brake snap ring from the transmission case.

    Text in Illustration 
    *1
    Protective Tape

    NOTICE:
    Be careful not to damage the transmission case.

    HINT:
    Wrap the tip of the screwdriver with tape.


60. REMOVE NO. 3 BRAKE DISC SET
  1. Remove the 2 flanges, 4 discs and 3 plates from the transmission case.


61. INSPECT NO. 3 BRAKE DISC

C161778
  1. Replace all discs if one of the following problems is present: 1) a disc, plate or flange is worn or burnt, 2) the lining of a disc is peeled off or discolored, or 3) grooves or printed numbers have even a little bit of damage.

    NOTICE:
    Before assembling new discs, soak them in ATF for at least 2 hours.


62. REMOVE NO. 3 BRAKE PISTON HOLE SNAP RING

C161708E01
  1. Using SST, remove the snap ring.

    SST
    09350-30020   (09350-07060)


63. REMOVE NO. 3 BRAKE CYLINDER WITH NO. 3 BRAKE PISTON AND NO. 3 BRAKE PISTON RETURN SPRING SUB-ASSEMBLY

C161709
  1. Remove the No. 3 brake cylinder with the No. 3 brake piston and No. 3 brake piston return spring from the transmission case.


64. REMOVE NO. 3 BRAKE PISTON

C162151E01
  1. Using SST and a press, compress the No. 3 brake piston return spring and remove the snap ring and No. 3 brake piston return spring with a screwdriver.

    SST
    09380-60010   (09381-06020, 09381-06040, 09381-06060, 09381-06100, 09381-06110)

  1. C161712
    Hold the No. 3 brake piston and apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the No. 3 brake cylinder to remove the No. 3 brake piston.

  1. C161713
    Remove the 2 O-rings from the No. 3 brake piston.


65. INSPECT NO. 3 BRAKE PISTON RETURN SPRING SUB-ASSEMBLY

C161777
  1. Using a vernier caliper, measure the free length of the spring together with the spring seat.

    Standard free length:
    15.72 mm (0.619 in.)


66. REMOVE 1-WAY CLUTCH ASSEMBLY WITH 1-WAY CLUTCH INNER RACE SUB-ASSEMBLY

C161710
  1. Remove the 1-way clutch assembly with 1-way clutch inner race from the transmission case.


67. INSPECT 1-WAY CLUTCH ASSEMBLY

C161775E01
  1. Install the 1-way clutch to the 1-way clutch inner race.

  1. Hold the 1-way clutch inner race and turn the 1-way clutch. Check that the 1-way clutch turns freely counterclockwise and locks when turned clockwise.

  1. Remove the 1-way clutch from the 1-way clutch inner race.


68. REMOVE 1-WAY CLUTCH INNER RACE SUB-ASSEMBLY

C161711
  1. Separate the 1-way clutch inner race from the 1-way clutch assembly and remove the No. 1 planetary carrier thrust washer.


69. REMOVE FRONT PLANETARY GEAR ASSEMBLY

C161714
  1. Remove the front planetary gear assembly and thrust needle roller bearing from the transmission case.

  1. C161715
    Remove the No. 2 planetary carrier thrust washer, thrust bearing race and front planetary sun gear from the front planetary gear assembly.


70. INSPECT FRONT PLANETARY GEAR ASSEMBLY

C161773
  1. Using a feeler gauge, measure the front planetary pinion gear thrust clearance.

    Standard clearance:
    0.2 to 0.6 mm (0.00787 to 0.0236 in.)

    1. If the clearance is more than the standard, replace the front planetary gear assembly.

  1. C161774
    Using a cylinder gauge, measure the inside diameter of the front planetary gear bush.

    Standard inside diameter:
    61.005 to 61.030 mm (2.402 to 2.403 in.)

    1. If the inside diameter is more than the standard, replace the front planetary gear.


71. REMOVE FRONT PLANETARY RING GEAR WITH FRONT PLANETARY RING GEAR FLANGE SUB-ASSEMBLY AND CENTER PLANETARY RING GEAR

C161716
  1. Remove the front planetary ring gear together with the front planetary ring gear flange and center planetary ring gear from the transmission case.

  1. Remove the thrust needle roller bearing and thrust bearing race.


72. REMOVE FRONT PLANETARY RING GEAR

C161717
  1. Using a screwdriver, remove the snap ring.

  1. C161718
    Remove the front planetary ring gear from the center planetary ring gear.


73. REMOVE CENTER PLANETARY RING GEAR

C161719
  1. Using a screwdriver, remove the snap ring.

  1. C161720
    Remove the center planetary ring gear from the front planetary ring gear flange.


74. REMOVE NO. 1 BRAKE DISC SET
  1. Remove the flange, 4 discs and 4 plates from the transmission case.


75. INSPECT NO. 1 BRAKE DISC

C161776
  1. Replace all discs if one of the following problems is present: 1) a disc, plate or flange is worn or burnt, 2) the lining of a disc is peeled off or discolored, or 3) grooves or printed numbers have even a little bit of damage.

    NOTICE:
    Before assembling new discs, soak them in ATF for at least 2 hours.


76. REMOVE NO. 1 BRAKE CYLINDER WITH NO. 1 BRAKE PISTON

C228991E01
  1. Place SST on the brake piston return spring and compress the brake piston return spring.

    SST
    09380-60010   (09381-06010, 09381-06020, 09381-06050, 09381-06060, 09381-06090, 09381-06100, 09381-06110, 09381-06120)

  1. Using a screwdriver, remove the snap ring from the transmission case.

    Text in Illustration 
    *1
    Protective Tape

    NOTICE:
    Be careful not to damage the transmission case.

    HINT:
    Wrap the tip of the screwdriver with tape.

  1. C161723
    Remove the brake piston return spring and No. 1 brake piston with No. 1 brake cylinder from the transmission case.


77. INSPECT BRAKE PISTON RETURN SPRING SUB-ASSEMBLY

C161772
  1. Using a vernier caliper, measure the free length of the spring together with the spring seat.

    Standard free length:
    17.05 mm (0.671 in.)


78. REMOVE NO. 1 BRAKE PISTON

C161724
  1. Hold the No. 1 brake piston and apply compressed air to the No. 1 brake cylinder to remove the No. 1 brake piston.

    HINT:
    If the piston does not pop out with compressed air, lift the piston out with needle-nose pliers.

  1. C162732
    Remove the 2 O-rings from the No. 1 brake piston.


79. REMOVE CENTER PLANETARY GEAR ASSEMBLY

C161727
  1. Remove the center planetary gear assembly and center planetary sun gear from the transmission case.


80. INSPECT CENTER PLANETARY GEAR ASSEMBLY

C161749
  1. Using a feeler gauge, measure the center planetary pinion gear thrust clearance.

    Standard clearance:
    0.20 to 0.60 mm (0.00787 to 0.0236 in.)

    1. If the clearance is more than the standard, replace the center planetary gear assembly.


81. REMOVE NO. 2 BRAKE DISC SET

C228990E01
  1. Place SST on the flange and compress the No. 2 brake piston return spring.

    SST
    09380-60010   (09381-06010, 09381-06020, 09381-06050, 09381-06070, 09381-06090, 09381-06120)

  1. Using a screwdriver, remove the snap ring from the transmission case.

    Text in Illustration 
    *1
    Protective Tape

    NOTICE:
    Be careful not to damage the transmission case.

    HINT:
    Wrap the tip of the screwdriver with tape.

  1. Remove the No. 2 brake flange, flange, 4 discs, 3 plates and No. 2 brake piston return spring from the transmission case.


82. INSPECT NO. 2 BRAKE DISC

C161770
  1. Replace all discs if one of the following problems is present: 1) a disc, plate or flange is worn or burnt, 2) the lining of a disc is peeled off or discolored, or 3) grooves or printed numbers have even a little bit of damage.

    NOTICE:
    Before assembling new discs, soak them in ATF for at least 2 hours.


83. INSPECT NO. 2 BRAKE PISTON RETURN SPRING SUB-ASSEMBLY

C161771
  1. Using a vernier caliper, measure the free length of the spring together with the spring seat.

    Standard free length:
    22.66 mm (0.892 in.)


84. REMOVE NO. 2 BRAKE CYLINDER WITH NO. 2 BRAKE PISTON

C161728
  1. Remove the No. 2 brake cylinder together with the No. 2 brake piston from the transmission case.


85. REMOVE NO. 2 BRAKE PISTON

C162149
  1. Hold the No. 2 brake piston and apply compressed air to the No. 2 brake cylinder to remove the No. 2 brake piston.

    HINT:
    If the piston does not pop out with compressed air, lift the piston out with needle-nose pliers.

  1. C162730
    Remove the 2 O-rings from the No. 2 brake piston.


86. REMOVE INTERMEDIATE SHAFT WITH NO. 3 1-WAY CLUTCH ASSEMBLY, REAR PLANETARY RING GEAR FLANGE AND REAR PLANETARY RING GEAR

C161730E01
  1. Using SST, remove the snap ring from the transmission case.

    SST
    09350-30020   (09350-07060)

  1. C161731
    Remove the intermediate shaft with No. 3 1-way clutch assembly, rear planetary ring gear flange and rear planetary ring gear from the transmission case.


87. INSPECT NO. 3 1-WAY CLUTCH ASSEMBLY

C161748E01
  1. Hold the rear planetary ring gear flange and turn the 1-way clutch. Check that the 1-way clutch turns freely counterclockwise and locks when turned clockwise.


88. REMOVE 1-WAY CLUTCH INNER RACE

C161732
  1. Remove the No. 3 1-way clutch assembly and 1-way clutch inner race from the intermediate shaft.


89. REMOVE REAR PLANETARY RING GEAR

C161733
  1. Remove the rear planetary ring gear with rear planetary ring gear flange, 3 thrust bearing races and thrust needle roller bearing from the intermediate shaft.

  1. C161734
    Using a screwdriver, remove the snap ring.

  1. Remove the rear planetary ring gear flange from the rear planetary ring gear.


90. INSPECT INTERMEDIATE SHAFT

C161746E01
  1. Using a dial indicator, check the intermediate shaft runout.

    Standard runout:
    0.03 mm (0.00118 in.)

    If the runout is more than the standard, replace the intermediate shaft with a new one.

  1. C161747E01
    Using a micrometer, check the diameter of the intermediate shaft at the positions shown in the diagram.

    Standard diameter:
    A:
    19.963 to 19.976 mm (0.7859 to 0.7865 in.)
    B, C:
    30.150 to 30.163 mm (1.187 to 1.188 in.)
    D, E:
    36.404 to 36.420 mm (1.433 to 1.434 in.)

    If the diameter is less than the standard, replace the intermediate shaft with a new one.


91. REMOVE NO. 4 BRAKE DISC SET
  1. Remove the No. 4 brake flange, flange, 7 No. 4 brake discs and 6 plates from the transmission case.


92. INSPECT NO. 4 BRAKE DISC

  1. C161745
    Replace all discs if one of the following problems is present: 1) a disc, plate or flange is worn or burnt, 2) the lining of a disc is peeled off or discolored, or 3) grooves or printed numbers have even a little bit of damage.

    NOTICE:
    Before assembling new discs, soak them in ATF for at least 2 hours.


93. REMOVE BRAKE PLATE STOPPER SPRING

C161735

NOTICE:
When removing the brake plate stopper spring, do not apply excessive force and do not deform it.


94. REMOVE REAR PLANETARY GEAR ASSEMBLY

C162771
  1. Remove the rear planetary gear assembly from the transmission case.

  1. C162772
    Remove the 2 thrust needle roller bearings from the rear planetary gear assembly.

  1. C161739
    Remove the thrust bearing race from the transmission case.


95. INSPECT REAR PLANETARY GEAR ASSEMBLY

  1. C161743
    Using a feeler gauge, measure the rear planetary pinion gear thrust clearance.

    Standard clearance:
    0.2 to 0.6 mm (0.00787 to 0.0236 in.)

    1. If the clearance is more than the standard, replace the planetary gear assembly.

  1. C161744
    Using a dial indicator, measure the inside diameter of the rear planetary gear bush.

    Standard inside diameter:
    20.0 to 20.025 mm (0.787 to 0.788 in.)

    1. If the inside diameter is more than the standard, replace the rear planetary gear assembly.


96. REMOVE 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY

C162152E01
  1. Place SST on the 1st and reverse brake return spring and compress the 1st and reverse brake return spring.

    SST
    09380-60010   (09381-06030, 09381-06040, 09381-06080, 09381-06120, 09381-06130, 09381-05040, 09381-05050)

  1. Using SST, remove the snap ring and 1st and reverse brake return spring.

    SST
    09350-30020   (09350-07070)

  1. C161740
    Hold the 1st and reverse brake piston and apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the transmission case to remove the 1st and reverse brake piston.

    HINT:
    If the piston does not pop out with compressed air, lift the piston out with needle-nose pliers.

  1. C161741
    Remove the 3 O-rings from the 1st and reverse brake piston.


97. INSPECT 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY

C161742
  1. Using a vernier caliper, measure the free length of the spring together with the spring seat.

    Standard free length:
    23.54 to 23.94 mm (0.927 to 0.943 in.)

← DISASSEMBLY (Sep 2011 – Dec 2011)INSPECTION (from Sep 2011) →