2011-2013 Land Cruiser · Service Manual Engine / Hybrid / EV System

ON-VEHICLE INSPECTION

Inspection · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

HINT:
In a malfunction where the EGR system is always on, black or white smoke may be emitted from the exhaust pipe.


CHECK SEATING OF EGR VALVE (w/ EGR System)
  1. Start the engine, and then check that the engine starts and runs at idle.


CHECK ENGINE CONDITION (w/ EGR System)
  1. Connect the intelligent tester to the DLC3.

  1. Start the engine, then run it at idle.

  1. Turn the intelligent tester on.

  1. Warm up the engine.

    HINT:
    The coolant temperature should be between 75°C (167°F) and 90°C (194°F).

  1. Enter the following menus: Powertrain / Engine / Data List / Actual EGR Valve Pos. or Actual EGR Valve Pos. #2.

  1. Check that the value of the EGR angle is within the specification.

    Standard Percentage:
    Engine Condition
    EGR Valve Opening Angle Expressed as Percentage
    During idling
    0 to 80%

    If the result is not as specified, refer to the EGR valve inspection procedures (Click here).

  1. Turn the ignition switch off.


CHECK EGR VALVE OPERATION (w/ EGR System)
  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Powertrain / Engine / Active Test / Control the EGR step position or Control the EGR step position #2.

  1. Check the Data List / EGR Lift Sensor Output, Actual EGR Valve Pos. or Actual EGR Valve Pos. #2 reading.

    HINT:
    Make sure the EGR valve opening angle changes according to the Active Test operation.

    Standard Percentage:
    Control Range Condition
    Specified Condition
    Active Test performed (Set EGR position to 100%)
    EGR Valve Angle: 73 to 100%
    Active Test performed (Set EGR position to 0%)
    EGR Valve Angle: 0 to 27%

    If the result is not as specified, refer to DTC P0400 (Click here).


CHECK MAF AMOUNT (w/ EGR System)
  1. Start the engine, then run it at idle.

  1. Warm up the engine.

    HINT:
    The coolant temperature should be between 75°C (167°F) and 90°C (194°F).

  1. Turn the intelligent tester on.

  1. Enter the following menus: Powertrain / Engine / Data List / MAF.

  1. Check the MAF reading.

  1. Enter the following menus: Powertrain / Engine / Active Test / Control the EGR step position or Control the EGR step position #2.

    HINT:
    1. In the Active Test, the EGR valve of bank 1 and bank 2 cannot be operated at the same time.
    2. In the Active Test, the change in the MAF amount is difficult to check because the EGR valve can only be operated one bank at a time. Therefore, use the value below as a reference and check that the MAF amount changes.

    Standard (Reference):
    Engine Condition
    Active Test Condition
    MAF Reading
    Idling
    Active Test performed (Set EGR position to 0%)
    Air flow amount changes
    (Approximately 7.8 to 26.5 g/sec.)


VISUALLY INSPECT HOSES, CONNECTIONS AND GASKETS

  1. A184398
    Visually check that the hoses, connections and gaskets have no cracks, leaks or damage.

    NOTICE:
    1. Detachment or other problems with the engine oil dipstick, filler cap, PCV hose and other components may cause the engine to run improperly.
    1. Air suction caused by disconnections, looseness or cracks in the parts of the air induction system between the throttle body and cylinder head will cause engine failure or engine malfunctions.

    If the result is not as specified, replace parts as necessary.

← SYSTEM DIAGRAM (from Jan 2012)ON-VEHICLE INSPECTION (from Jan 2012) →