2011-2013 Land Cruiser · Service Manual Drivetrain

DISASSEMBLY

Removal / installation · Vehicles built from Sep 2011


1. REMOVE DIFFERENTIAL EXTENSION FLANGE TUBE

  1. C171952
    Remove the 4 bolts.

  1. Using a plastic-faced hammer, remove the differential tube.


2. REMOVE DIFFERENTIAL SIDE GEAR SHAFT OIL SEAL

  1. C159259E02
    Using SST, tap out the oil seal.
    SST
    09308-00010  


3. REMOVE FRONT DRIVE PINION COMPANION FLANGE FRONT NUT

  1. C159261E02
    Using SST and a hammer, unstake the nut.
    SST
    09930-00010  

  1. C159262E02
    Using SST to hold the companion flange, remove the nut.
    SST
    09330-00021   (09330-00030)


4. REMOVE FRONT DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY

  1. C159263E04
    Using SST, remove the companion flange from the differential carrier.
    SST
    09950-30012   (09951-03010, 09953-03010, 09954-03010, 09955-03030, 09956-03020)


5. REMOVE FRONT DIFFERENTIAL CARRIER OIL SEAL

  1. C159264E02
    Using SST, remove the oil seal.
    SST
    09308-10010  


6. REMOVE FRONT DIFFERENTIAL DRIVE PINION OIL SLINGER

7. REMOVE FRONT DIFFERENTIAL CROSS SHAFT BEARING RETAINER

  1. C160133E01
    Remove the bolts labeled B and front differential front support assembly LH.

  1. Remove the bolts labeled A.

  1. Using a plastic-faced hammer, tap out the bearing retainer.


8. REMOVE FRONT NO. 1 DIFFERENTIAL CASE SUB-ASSEMBLY
  1. Remove the differential case from the differential carrier.


9. REMOVE DIFFERENTIAL DRIVE PINION

  1. C159434E02
    Set the differential carrier to an overhaul stand as shown in the illustration.

  1. Using a press, press out the drive pinion.

    NOTICE:
    Do not drop the drive pinion.


10. REMOVE FRONT DRIVE PINION FRONT RADIAL BALL BEARING
  1. Remove the bearing (inner race) from the differential carrier.


11. REMOVE FRONT DIFFERENTIAL BREATHER PLUG OIL DEFLECTOR

  1. C159446
    Remove the 2 bolts and oil deflector.


12. REMOVE FRONT DIFFERENTIAL UNION

  1. C159447
    Remove the front differential union from the differential carrier.


13. REMOVE FRONT DRIVE PINION REAR TAPERED ROLLER BEARING

  1. C116049E01
    Using SST and a press, press out the bearing (inner race) from the drive pinion.
    SST
    09950-00020  
    If the drive pinion or ring gear is damaged, replace them as a set.


14. REMOVE FRONT DRIVE PINION REAR TAPERED ROLLER BEARING

  1. C159337
    Using a brass bar and hammer, tap out the bearing (outer race) and washer.


15. REMOVE FRONT DRIVE PINION FRONT RADIAL BALL BEARING

  1. C159338E02
    Using SST and a hammer, tap out the bearing (outer race) from the differential carrier.
    SST
    09950-70010   (09951-07100)
    09950-60010   (09951-00450)
    09950-60020   (09951-00710, 09952-06010)


16. REMOVE FRONT DIFFERENTIAL CASE BEARING

HINT:
  1. Measure the plate washer and note its thickness.
  2. Tag the bearing outer races to show the location for reassembly.

  1. C159266E02
    Using SST and a press, press out the bearing (outer race) and plate washer from the bearing retainer.
    SST
    09950-60020   (09951-00680)
    09950-70010   (09951-07150)

  1. C159267E02
    Using SST and a press, press out the bearing (outer race) and plate washer from the differential carrier.
    SST
    09950-60020   (09951-00680)
    09950-70010   (09951-07150)


17. REMOVE DIFFERENTIAL RING GEAR

  1. C159243E02
    Place matchmarks on the ring gear and differential case.

  1. Remove the 12 bolts.

  1. Using a plastic-faced hammer, tap on the ring gear to disconnect it from the differential case.


18. REMOVE FRONT DIFFERENTIAL CASE BEARING

  1. C159244E02
    Using SST, remove the 2 bearings (inner race).
    SST
    09950-60010   (09951-00390)
    09950-40011   (09951-04020, 09952-04010, 09953-04030, 09954-04010, 09955-04061, 09957-04010, 09958-04011)

    HINT:
    Fix the claws of SST into the notch in the differential case assembly.


19. DISASSEMBLE DIFFERENTIAL CASE

  1. C159245E02
    Using a pin punch and hammer, tap out the straight pin.

  1. Remove these parts from the differential case assembly.

    1. 2 differential side gears

    2. 2 differential side gear thrust washers

    3. Differential pinion shaft

    4. 2 differential pinion gears

    5. 2 differential pinion gear thrust washers


20. INSPECT DIFFERENTIAL GEAR KIT
  1. Check that there is no damage to the pinion gears and side gears.
    If a pinion gear and/or side gear is damaged, replace the differential gear kit.


21. INSPECT FRONT NO. 1 DIFFERENTIAL CASE SUB-ASSEMBLY
  1. Check that the differential case is not damaged.
    If the differential case is damaged, replace it.


22. REMOVE DIFFERENTIAL SIDE GEAR SHAFT OIL SEAL

  1. R013199E03
    Using SST, tap out the oil seal from the flange tube.
    SST
    09308-00010  


23. REMOVE DIFFERENTIAL SIDE GEAR SHAFT SUB-ASSEMBLY RH

  1. C159248
    Using a snap ring pliers, remove the snap ring.

  1. C171953
    Using a plastic-faced hammer, tap out the side gear shaft.


24. REMOVE FRONT DIFFERENTIAL SIDE GEAR SHAFT RH BEARING

  1. C171954
    Using a snap ring expander, remove the snap ring.

  1. C159250E03
    Using SST and a press, press out the bearing.
    SST
    09950-00020  
    09950-70010   (09951-07100)
    09950-60010   (09951-00450)

    NOTICE:
    Do not damage the bearing.


25. REMOVE FRONT DIFFERENTIAL CARRIER STRAIGHT PIN

  1. C176512
    Remove the straight pins from the bearing retainer.


26. REMOVE FRONT DIFFERENTIAL TUBE STRAIGHT PIN

  1. C176513
    Remove the straight pins from the bearing retainer.

← REMOVAL (from Sep 2011)REASSEMBLY (from Sep 2011) →