2011-2013 Land Cruiser · Service Manual Drivetrain

REASSEMBLY

Removal / installation · Vehicles built from Sep 2011

NOTICE:
Do not allow brake fluid, front differential oil, gasoline, or battery fluid to contact the drive shaft boots, as the boots may be damaged.


1. INSTALL FRONT DRIVE SHAFT DUST COVER LH

  1. C173428E01
    Using SST, a steel plate and press, press in a new dust cover.
    SST
    09316-20011  

    Standard length (A):
    108.4 to 109.0 mm (4.27 to 4.29 in.)

    NOTICE:
    Be careful not to damage the dust cover.


2. INSTALL DUST SEAL

C222938E01
  1. Using SST and a press, press in a new dust seal until it reaches the end of the outboard joint shaft assembly.

    SST
    09950-00020  

    NOTICE:
    Be careful not to damage the dust seal.

    HINT:
    Place SST on a level surface.


3. INSTALL FRONT AXLE OUTBOARD JOINT BOOT

  1. C115636E02
    Slide a new outboard joint boot onto the outboard joint shaft.

    HINT:
    Before installing the boot, wrap vinyl tape around the spline of the shaft to prevent damaging the boot.

  1. C177229
    Temporarily install the boot to the outboard joint shaft.

  1. Attach a new front No. 1 axle outboard joint boot setting clamp onto the boot.

  1. C115637E02
    Using SST, pinch the clamp.
    SST
    09521-24010  

    NOTICE:
    Do not overtighten SST.

  1. Pack the outboard joint and boot with grease from a boot kit.

    Standard grease capacity:
    310 to 320 g (11.0 to 11.2 oz.)

  1. Attach a new front No. 2 axle outboard joint boot setting clamp.

  1. C115638E02
    Using SST, pinch the clamp.
    SST
    09521-24010  

    NOTICE:
    Do not overtighten SST.

  1. C162200E03
    Using SST, adjust the clearance of the clamps.
    SST
    09240-00020  

    Standard clearance:
    1.5 mm (0.0591 in.)


4. TEMPORARILY INSTALL FRONT AXLE INBOARD JOINT BOOT

  1. C177090E01
    Slide a new inboard joint boot onto the outboard joint shaft.

    HINT:
    Before installing the boot, wrap vinyl tape around the spline of the shaft to prevent damaging the boot.


5. INSTALL FRONT AXLE INBOARD JOINT SHAFT

  1. C177163E01
    Install the cage to the outboard joint shaft.

    NOTICE:
    Insert the cage with its smaller inner diameter side facing the outboard joint.

  1. C158394E02
    Align the matchmarks placed before removal.

  1. Install the inner race.

  1. C158392
    Using a snap ring expander, install a new snap ring.

  1. C158395E02
    Align the matchmarks placed before removal, and install the cage to the inner race.

  1. C115633
    Install the 6 balls.

    HINT:
    Apply grease onto the balls to keep them from falling out.

  1. Pack the inboard joint shaft and boot with grease from a boot kit.

    Standard grease capacity:
    314 to 324 g (11.1 to 11.4 oz.)

  1. C172549E01
    Align the matchmarks placed before removal, and install the inboard joint shaft to the outboard joint shaft.

  1. Install a new snap ring.

  1. C177089
    Temporarily install the boot to the inboard joint shaft.

    HINT:
    Make sure that the boot is on the shaft groove.

  1. C175125E01
    Check that the 2 boots are not stretched or contracted when the drive shaft is at standard length.

    Standard drive shaft length (A):
    583 mm (1.91 ft.)

    If the boots are stretched or contracted, correct them.

  1. C175129E01
    Using SST, attach a new front No. 1 axle inboard joint boot setting clamp.
    SST
    09521-24010  

    NOTICE:
    Do not overtighten SST.

  1. C175130E01
    Using SST, attach a new front No. 2 axle inboard joint boot setting clamp.
    SST
    09521-24010  

    NOTICE:
    Do not overtighten SST.

  1. C162199E02
    Using SST, adjust the clearance of the clamps.
    SST
    09240-00020  

    Standard clearance:
    1.5 mm (0.0591 in.)


6. INSTALL FRONT AXLE INBOARD JOINT SET SETTING SHAFT SNAP RING

  1. C174231
    Install a new snap ring to the inboard joint shaft.


7. INSPECT FRONT DRIVE SHAFT ASSEMBLY

NOTICE:
Move the drive shaft while keeping it level.

  1. C175123
    Check if there is excessive play in the outboard joint.

  1. Check if the inboard joint shaft slides smoothly in the thrust direction.

  1. Check if there is excessive play in the radial direction of the inboard joint shaft.

  1. Check the boots for damage.

  1. C175125
    Check that the 2 boots are not stretched or contracted when the drive shaft is at standard length.

    Standard drive shaft length:
    583 mm (1.91 ft.)

    If the boots are stretched or contracted, correct them.

← INSPECTION (from Sep 2011)INSTALLATION (from Sep 2011) →