2011-2013 Land Cruiser · Service Manual Brake

REMOVAL

Removal / installation · Vehicles built from Jan 2012

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

NOTICE:
  1. Be sure not to allow the pump to contact the floor; support it with the booster body. If the pump contacts the floor, the red brake tube between the pump and booster body may be deformed, the operating sound of the pump may become loud enough to hear within the cabin, and fluid may leak.
  2. When installing, coat the parts indicated by arrows with lithium soap base glycol grease (Click here).
  3. As high pressure is applied to the brake actuator tube No. 1, never deform it.
  4. Until the work is over, do not turn the ignition switch on.
  5. Before starting the work, make sure that the ignition switch is off and depress the brake pedal more than 20 times.

HINT:
When pressure in the power supply system is released, the reaction force becomes light and the stroke becomes longer.


1. DRAIN BRAKE FLUID

NOTICE:
Wash off brake fluid immediately if it comes into contact with a painted surface.


2. PRECAUTION

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).


3. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


4. REMOVE FRONT DOOR SCUFF PLATE RH

5. REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

B180655
  1. Remove the 2 screws.

  1. Detach the 3 claws.

  1. Disconnect the connectors and remove the No. 1 instrument panel under cover.


6. REMOVE COWL SIDE TRIM BOARD RH

B180022
  1. Remove the cap nut.

  1. Detach the 2 clips and remove the cowl side trim board.


7. REMOVE LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL

B180295E02
  1. Using a screwdriver, detach the 2 claws and open the hole cover.

    HINT:
    Tape the screwdriver tip before use.

    Text in Illustration 
    *1
    Protective Tape

  1. w/ Driver Side Knee Airbag:

    1. Remove the 2 bolts.

    2. Detach the 16 claws.

      B291249

  1. w/o Driver Side Knee Airbag:

    1. Remove the 2 bolts.

    2. Detach the 9 claws.

      B291250

  1. B180296
    for Automatic Air Conditioning System:

    1. Detach the 2 claws and remove the room temperature sensor.

  1. B181942
    Detach the 2 claws and disconnect the 2 control cables.

  1. Disconnect the connectors and remove the lower No. 1 instrument panel finish panel.


8. REMOVE DRIVER SIDE KNEE AIRBAG ASSEMBLY

  1. B189602E01
    Remove the 5 bolts and driver side knee airbag.

  1. Disconnect the connector.

    NOTICE:
    When handling the airbag connector, take care not to damage the airbag wire harness.


9. REMOVE PUSH ROD PIN

  1. C172862
    Remove the clip and push rod pin from the brake pedal lever.


10. REMOVE HYDRAULIC BRAKE BOOSTER ASSEMBLY

  1. C172863
    Disconnect the 3 connectors from the hydraulic brake booster.

  1. F051200E02
    Use tags or make a memo to identify the place to reconnect.

  1. C172864E01
    Using a union nut wrench, disconnect the 4 brake lines from the hydraulic brake booster.

  1. Remove the bolt and disconnect the clamp from the hydraulic brake booster assembly.

  1. C172861
    Remove the 4 nuts and pull out the hydraulic brake booster assembly.


11. REMOVE BRAKE BOOSTER GASKET
  1. Remove the brake booster gasket from the hydraulic brake booster assembly.

← REMOVAL (Sep 2011 – Dec 2011)DISASSEMBLY (from Sep 2011) →