2011-2013 Land Cruiser · Service Manual Engine / Hybrid / EV System

P0100 Mass or Volume Air Flow Circuit

Diagnostic trouble codes · Vehicles built from Jan 2012

Also covers:

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

DESCRIPTION

The Mass Air Flow (MAF) meter uses a platinum hot wire. The mass air flow meter consists of a platinum hot wire, a temperature sensor and a control circuit installed in a plastic housing. The mass air flow meter hot wire and temperature sensor (located in the intake air by-pass of the housing) detect changes in the intake air temperature.
The hot wire is maintained at the predetermined temperature by controlling the current flow through the hot wire. This current flow is then used as the output voltage of the mass air flow meter.
The circuit is constructed so that the platinum hot wire and temperature sensor provide a bridge circuit, with the power transistor controlled so that the potential of A and B remains equal to maintain the predetermined temperature.
A160257E01
P0100 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Ignition switch ON for 3 seconds
Mass air flow (MAF) meter voltage is 0.2 V or less, or 4.9 V or more with the engine speed at 4000 rpm or less for 3 seconds (1 trip detection logic).
  1. Open or short in Mass Air Flow (MAF) meter circuit
  2. Mass air flow meter
  3. ECM
P0102 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Ignition switch ON for 3 seconds
MAF meter voltage is 0.2 V or less with the engine speed at 4000 rpm or less for 3 seconds (1 trip detection logic).
  1. Open in Mass Air Flow (MAF) meter circuit
  2. Mass air flow meter
  3. ECM
P0103 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Ignition switch ON for 3 seconds
MAF meter voltage is 4.9 V or more with the engine speed at 4000 rpm or less for 3 seconds (1 trip detection logic).
  1. Shot in Mass Air Flow (MAF) meter circuit
  2. Mass air flow meter
  3. ECM
Related Data List 
DTC No.
Data List
P0100
MAF
P0102
P0103

HINT:
  1. If DTC P0100, and/or P0102 is stored, the following symptoms may appear (as the ECU mistakenly determines that there is less air than the actual intake air amount, EGR is decreased to match the target EGR):
    1. Combustion noise worsens
  2. If DTC P0100, and/or P0103 is stored, the following symptoms may appear (as the ECU mistakenly determines that there is more air than the actual intake air amount, EGR is increased to match the target EGR):
    1. Misfire
    2. White smoke
    3. Black smoke
  3. After confirming DTC P0100, P0102 or P0103, check the mass air flow ratio by entering the following menus: Powertrain / Engine / Data List / MAF.
    Reference: 
    Air Flow Value (g/sec.)
    Malfunction
    Approximately 0.0
    1. Open in mass air flow meter power source circuit
    2. Open or short in VG circuit
    174.0 or more
    Open in EVG circuit


WIRING DIAGRAM

A182250E02

INSPECTION PROCEDURE

NOTICE:
After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).

HINT:
Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


1. READ VALUE USING INTELLIGENT TESTER (MASS AIR FLOW RATE)
  1. Connect the intelligent tester to the DLC3.

  1. Start the engine and turn the tester on.

  1. Enter the following menus: Powertrain / Engine / Data List / MAF.

  1. Read the value.

    Result 
    Result
    Proceed to
    0.0
    A
    174.0 or more
    B
    Between 1 and 173.0*
    C

HINT:
*: The value should change when the throttle valve is opened or closed.



B
Go to step 8

C
Go to step 15
A


2. INSPECT MASS AIR FLOW METER (POWER SOURCE CIRCUIT)
A148358E10
  1. Disconnect the mass air flow meter connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    C50-1 (+B) - Body ground
    Ignition switch ON
    11 to 14 V



NG
Go to step 5
OK


3. INSPECT MASS AIR FLOW METER
  1. Inspect the mass air flow meter (Click here).



NG
Go to step 11
OK


4. CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)

  1. A182382E01
    Disconnect the mass air flow meter connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    for LHD 
    Tester Connection
    Condition
    Specified Condition
    C50-3 (VG) - C45-72 (VG)
    Always
    Below 1 Ω
    C50-2 (E2G) - C45-118 (EVG)
    Always
    Below 1 Ω
    for RHD 
    Tester Connection
    Condition
    Specified Condition
    C50-3 (VG) - C46-72 (VG)
    Always
    Below 1 Ω
    C50-2 (E2G) - C46-118 (EVG)
    Always
    Below 1 Ω


    Standard Resistance (Check for Short):
    for LHD 
    Tester Connection
    Condition
    Specified Condition
    C50-3 (VG) or C45-72 (VG) - Body ground
    Always
    10 kΩ or higher
    for RHD 
    Tester Connection
    Condition
    Specified Condition
    C50-3 (VG) or C46-72 (VG) - Body ground
    Always
    10 kΩ or higher



OK
Go to step 10

NG
Go to step 12
5. INSPECT FUSE (EFI NO. 2)
A182379E01
  1. Remove the EFI NO. 2 fuse from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    EFI NO. 2 fuse
    Always
    Below 1 Ω



NG
Go to step 13
OK


6. CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ENGINE ROOM RELAY BLOCK)

  1. A182380E01
    Disconnect the mass air flow meter connector.

  1. Remove the EFI NO. 2 fuse from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    C50-1 (+B) - EFI NO. 2 fuse (2)
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    C50-1 (+B) or EFI NO. 2 fuse (2) - Body ground
    Always
    10 kΩ or higher



NG
Go to step 12
OK


7. CHECK HARNESS AND CONNECTOR (ENGINE ROOM RELAY BLOCK)
A182381E01
  1. Remove the EFI NO. 2 fuse from the engine room relay block.

  1. Remove the integration relay from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    EFI NO. 2 fuse (1) - 1B-4
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    EFI NO. 2 fuse (1) or 1B-4 - Body ground
    Always
    10 kΩ or higher



OK
Go to step 14

NG
Go to step 12
8. CHECK HARNESS AND CONNECTOR (SENSOR GROUND)

  1. A148358E11
    Disconnect the mass air flow meter connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    C50-2 (E2G) - Body ground
    Always
    Below 1 Ω



OK
Go to step 11

NG
Go to step 9
9. CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)

  1. A182382E01
    Disconnect the mass air flow meter connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    for LHD 
    Tester Connection
    Condition
    Specified Condition
    C50-3 (VG) - C45-72 (VG)
    Always
    Below 1 Ω
    C50-2 (E2G) - C45-118 (EVG)
    Always
    Below 1 Ω
    for RHD 
    Tester Connection
    Condition
    Specified Condition
    C50-3 (VG) - C46-72 (VG)
    Always
    Below 1 Ω
    C50-2 (E2G) - C46-118 (EVG)
    Always
    Below 1 Ω


    Standard Resistance (Check for Short):
    for LHD 
    Tester Connection
    Condition
    Specified Condition
    C50-3 (VG) or C45-72 (VG) - Body ground
    Always
    10 kΩ or higher
    for RHD 
    Tester Connection
    Condition
    Specified Condition
    C50-3 (VG) or C46-72 (VG) - Body ground
    Always
    10 kΩ or higher



NG
Go to step 12
OK


10. REPLACE ECM
  1. Replace the ECM (Click here).



NEXT
Go to step 15
11. REPLACE MASS AIR FLOW METER
  1. Replace the mass air flow meter (Click here).



NEXT
Go to step 15
12. REPAIR OR REPLACE HARNESS OR CONNECTOR


NEXT
Go to step 15
13. CHECK FOR SHORTS IN ALL HARNESSES AND CONNECTORS CONNECTED TO FUSE AND REPLACE FUSE


NEXT
Go to step 15
14. CHECK ECM POWER SOURCE CIRCUIT
  1. Check the ECM power source circuit (Click here).


NEXT


15. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
  1. Connect the intelligent tester to the DLC3.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON for 3 seconds

  1. Enter the following menus: Powertrain / Engine / DTC.

  1. Confirm that the DTC is not output again.


NEXT

END


← P0100 Mass or Volume Air Flow Circuit (+ P0102, P0103) (Sep 2011 – Dec 2011)P0101 Mass or Volume Air Flow Circuit Range / Performance Problem (Sep 2011 – Dec 2011) →