2011-2013 Land Cruiser · Service Manual Engine / Hybrid / EV System

P0112 Intake Air Temperature Circuit Low Input

Diagnostic trouble codes · Vehicles built from Jan 2012

Also covers:

DESCRIPTION

The intake air temperature sensor is built into the mass air flow meter and detects the intake air temperature.
A thermistor built into the sensor changes its resistance value according to the intake air temperature.
The lower the intake air temperature, the higher the thermistor resistance value. The higher the intake air temperature, the lower the thermistor resistance value (See Fig. 1).
The intake air temperature sensor is connected to the ECM.
The 5 V power source voltage from the ECM is applied to the intake air temperature sensor from terminal THA via resistor R.
Resistor R and the intake air temperature sensor are connected in series. When the resistance value of the intake air temperature sensor changes in accordance with the intake air temperature, the voltage at terminal THA also changes. Based on this signal, the ECM increases the fuel injection volume to improve driveability with a cold engine.
A208462E01
P0112 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Engine switch on (IG) for 0.5 seconds
Short in the intake air temperature sensor for 0.5 seconds (1 trip detection logic).
  1. Short in intake air temperature sensor circuit
  2. Intake air temperature sensor (built into mass air flow meter)
  3. ECM
P0113 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Engine switch on (IG) for 0.5 seconds
Open in the intake air temperature sensor for 0.5 seconds (1 trip detection logic).
  1. Open in intake air temperature sensor circuit
  2. Intake air temperature sensor (built into mass air flow meter)
  3. ECM
Related Data List 
DTC No.
Data List
P0112
P0113
Intake Air

HINT:
  1. If DTC P0112 and/or P0113 is stored, the following symptoms may appear:
    1. Misfire
    2. Combustion noise
    3. Black smoke
    4. White smoke
    5. Lack of power
  2. When DTC P0112 or P0113 is stored, check the intake air temperature by entering the following menus: Engine and ECT / Data List / Intake Air.
    Reference 
    Temperature Displayed
    Malfunction
    -40°C (-40°F)
    Open circuit
    140°C (284°F) or higher
    Short circuit


WIRING DIAGRAM

A165735E12

INSPECTION PROCEDURE

NOTICE:
  1. After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).
  2. After replacing the fuel supply pump assembly, the ECM needs initialization (Click here).
  3. After replacing an injector assembly, the ECM needs registration (Click here).

HINT:
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


1. READ VALUE USING GTS (INTAKE AIR TEMPERATURE)
  1. Connect the GTS to the DLC3.

  1. Turn the engine switch on (IG) and turn the GTS on.

  1. Enter the following menus: Engine and ECT / Data List / Intake Air.

  1. Read the value.

    OK:
    Same as actual intake air temperature

    Result 
    Result
    Proceed to
    -40°C (-40°F)
    A
    140°C (284°F) or higher
    B
    OK (same as actual intake air temperature)
    C

    HINT:
    1. If there is an open circuit, the GTS indicates -40°C (-40°F).
    2. If there is a short circuit, the GTS indicates 140°C (284°F) or higher.



B
Go to step 4

C
Go to step 11
A


2. READ VALUE USING GTS (CHECK FOR OPEN IN WIRE HARNESS)

  1. A128460E18
    Disconnect the mass air flow meter connector.

  1. Connect terminals 4 (THA) and 5 (E2) of the mass air flow meter wire harness side connector.

  1. Connect the GTS to the DLC3.

  1. Turn the engine switch on (IG) and turn the GTS on.

  1. Enter the following menus: Engine and ECT / Data List / Intake Air.

  1. Read the value.

    OK:
    140°C (284°F) or higher

    Text in Illustration 
    *1
    Mass air flow meter
    *2
    ECM
    *a
    Front view of wire harness connector
    (to Mass Air Flow Meter)



OK
Go to step 7

NG
Go to step 3
3. CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
  1. Disconnect the mass air flow meter connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LHD 
    Tester Connection
    Condition
    Specified Condition
    C50-4 (THA) - C45-115 (THA)
    Always
    Below 1 Ω
    C50-5 (E2) - C45-92 (E2)
    Always
    Below 1 Ω


    Standard Resistance:
    for RHD 
    Tester Connection
    Condition
    Specified Condition
    C50-4 (THA) - C46-115 (THA)
    Always
    Below 1 Ω
    C50-5 (E2) - C46-92 (E2)
    Always
    Below 1 Ω



OK
Go to step 9

NG
Go to step 8
4. READ VALUE USING GTS (CHECK FOR SHORT IN WIRE HARNESS)

  1. A198733E23
    Disconnect the mass air flow meter connector.

  1. Connect the GTS to the DLC3.

  1. Turn the engine switch on (IG) and turn the GTS on.

  1. Enter the following menus: Engine and ECT / Data List / Intake Air.

  1. Read the value.

    OK:
    -40°C (-40°F)

    Text in Illustration 
    *1
    Mass Air Flow Meter
    *2
    ECM



OK
Go to step 10

NG
Go to step 5
5. CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
  1. Disconnect the mass air flow meter connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LHD 
    Tester Connection
    Condition
    Specified Condition
    C50-4 (THA) or C45-115 (THA) - Body ground
    Always
    10 kΩ or higher


    Standard Resistance:
    for RHD 
    Tester Connection
    Condition
    Specified Condition
    C50-4 (THA) or C46-115 (THA) - Body ground
    Always
    10 kΩ or higher



NG
Go to step 8
OK


6. REPLACE ECM
  1. Replace the ECM (Click here).



NEXT
Go to step 11
7. CONFIRM GOOD CONNECTION TO SENSOR. IF OK, REPLACE MASS AIR FLOW METER.
  1. Replace the mass air flow meter (Click here).



NEXT
Go to step 11
8. REPAIR OR REPLACE HARNESS OR CONNECTOR
  1. Repair or replace the harness or connector.



NEXT
Go to step 11
9. CONFIRM GOOD CONNECTION TO ECM. IF OK, REPLACE ECM.
  1. Replace the ECM (Click here).



NEXT
Go to step 11
10. REPLACE MASS AIR FLOW METER
  1. Replace the mass air flow meter (Click here).


NEXT


11. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
  1. Connect the GTS to the DLC3.

  1. Clear the DTCs (Click here).

  1. Turn the engine switch on (IG) for 1 second.

  1. Enter the following menus: Engine and ECT / Trouble Codes.

  1. Confirm that the DTC is not output again.


NEXT

END


← P0107 Manifold Absolute Pressure / Barometric Pressure Circuit Low Input (+ P0108) (from Jan 2012)P0115 Engine Coolant Temperature Circuit (+ P0117, P0118) (from Jan 2012) →