2011-2013 Land Cruiser · Service Manual Engine / Hybrid / EV System

P0115 Engine Coolant Temperature Circuit

Diagnostic trouble codes · Vehicles built from Jan 2012

Also covers:

DESCRIPTION

A thermistor is built into the engine coolant temperature sensor and it changes its resistance value according to the engine coolant temperature.
The structure of the sensor and connection to the ECM is the same as that of the intake air temperature sensor.

HINT:
If DTC P0115, P0117 or P0118 is stored, the ECM operates the fail-safe function in which the engine coolant temperature is assumed to be 80°C (176°F).

P0115 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Engine switch on (IG) for 0.5 seconds
Open or short in the engine coolant temperature sensor circuit for 0.5 seconds (1 trip detection logic).
  1. Open or short in engine coolant temperature sensor circuit
  2. Engine coolant temperature sensor
  3. ECM
P0117 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Engine switch on (IG) for 0.5 seconds
Short in the engine coolant temperature sensor circuit for 0.5 seconds (1 trip detection logic).
  1. Short in engine coolant temperature sensor circuit
  2. Engine coolant temperature sensor
  3. ECM
P0118 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Engine switch on (IG) for 0.5 seconds
Open in the engine coolant temperature sensor circuit for 0.5 seconds (1 trip detection logic).
  1. Open in engine coolant temperature sensor circuit
  2. Engine coolant temperature sensor
  3. ECM
Related Data List 
DTC No.
Data List
P0115
P0117
P0118
Coolant Temp

HINT:
  1. If DTC P0115, P0117 and/or P0118 is stored, the following symptoms may appear:
    1. Misfire
    2. Combustion noise
    3. Black smoke
    4. White smoke
    5. Lack of power
  2. When DTC P0115, P0117 and/or P0118 is stored, check the engine coolant temperature by entering the following menus: Engine and ECT / Data List / Coolant Temp.
    Reference 
    Temperature Displayed
    Malfunction
    -40°C (-40°F)
    Open circuit
    140°C (284°F) or higher
    Short circuit


WIRING DIAGRAM

A165735E13

INSPECTION PROCEDURE

NOTICE:
  1. After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).
  2. After replacing the fuel supply pump assembly, the ECM needs initialization (Click here).
  3. After replacing an injector assembly, the ECM needs registration (Click here).

HINT:
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


1. READ VALUE USING GTS (ENGINE COOLANT TEMPERATURE)
  1. Connect the GTS to the DLC3.

  1. Turn the engine switch on (IG) and turn the GTS on.

  1. Enter the following menus: Engine and ECT / Data List / Coolant Temp.

  1. Read the value.

    OK:
    70 to 90°C (158 to 194°F) with warm engine

    Result 
    Result
    Proceed to
    -40°C (-40°F)
    A
    140°C (284°F) or higher
    B
    70 to 90°C (158 to 194°F)
    C

    HINT:
    1. If there is an open circuit, the GTS indicates -40°C (-40°F).
    2. If there is a short circuit, the GTS indicates 140°C (284°F) or higher.



B
Go to step 4

C
Go to step 11
A


2. READ VALUE USING GTS (CHECK FOR OPEN IN WIRE HARNESS)

  1. A213406E16
    Disconnect the engine coolant temperature sensor connector.

  1. Connect terminals 1 and 2 of the engine coolant temperature sensor wire harness side connector.

  1. Connect the GTS to the DLC3.

  1. Turn the engine switch on (IG) and turn the GTS on.

  1. Enter the following menus: Engine and ECT / Data List / Coolant Temp.

  1. Read the value.

    OK:
    140°C (284°F) or higher

    Text in Illustration 
    *1
    Engine Coolant Temperature Sensor
    *2
    ECM
    *a
    Front view of wire harness connector
    (to Engine Coolant Temperature Sensor)

  1. Reconnect the engine coolant temperature sensor connector.



OK
Go to step 7

NG
Go to step 3
3. CHECK HARNESS AND CONNECTOR (ENGINE COOLANT TEMPERATURE SENSOR - ECM)
  1. Disconnect the engine coolant temperature sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LHD 
    Tester Connection
    Condition
    Specified Condition
    C71-2 - C45-93 (THW)
    Always
    Below 1 Ω
    C71-1 - C45-92 (E2)
    Always
    Below 1 Ω
    for RHD 
    Tester Connection
    Condition
    Specified Condition
    C71-2 - C46-93 (THW)
    Always
    Below 1 Ω
    C71-1 - C46-92 (E2)
    Always
    Below 1 Ω

  1. Reconnect the engine coolant temperature sensor connector.

  1. Reconnect the ECM connector.



OK
Go to step 9

NG
Go to step 8
4. READ VALUE USING GTS (CHECK FOR SHORT IN WIRE HARNESS)

  1. A198733E24
    Disconnect the engine coolant temperature sensor connector.

  1. Connect the GTS to the DLC3.

  1. Turn the engine switch on (IG) and turn the GTS on.

  1. Enter the following menus: Engine and ECT / Data List / Coolant Temp.

  1. Read the value.

    OK:
    -40°C (-40°F)

    Text in Illustration 
    *1
    Engine Coolant Temperature Sensor
    *2
    ECM

  1. Reconnect the engine coolant temperature sensor connector.



OK
Go to step 10

NG
Go to step 5
5. CHECK HARNESS AND CONNECTOR (ENGINE COOLANT TEMPERATURE SENSOR - ECM)
  1. Disconnect the engine coolant temperature sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LHD 
    Tester Connection
    Condition
    Specified Condition
    C71-2 or C45-93 (THW) - Body ground
    Always
    10 kΩ or higher
    for RHD 
    Tester Connection
    Condition
    Specified Condition
    C71-2 or C46-93 (THW) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the engine coolant temperature sensor connector.

  1. Reconnect the ECM connector.



NG
Go to step 8
OK


6. REPLACE ECM
  1. Replace the ECM (Click here).



NEXT
Go to step 11
7. CONFIRM GOOD CONNECTION TO SENSOR. IF OK, REPLACE ENGINE COOLANT TEMPERATURE SENSOR.
  1. Replace the engine coolant temperature sensor (Click here).



NEXT
Go to step 11
8. REPAIR OR REPLACE HARNESS OR CONNECTOR
  1. Repair or replace the harness or connector.



NEXT
Go to step 11
9. CONFIRM GOOD CONNECTION TO ECM. IF OK, REPLACE ECM.
  1. Replace the ECM (Click here).



NEXT
Go to step 11
10. REPLACE ENGINE COOLANT TEMPERATURE SENSOR
  1. Replace the engine coolant temperature sensor (Click here).


NEXT


11. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
  1. Connect the GTS to the DLC3.

  1. Clear the DTCs (Click here).

  1. Turn the engine switch on (IG) for 1 second.

  1. Enter the following menus: Engine and ECT / Trouble Codes.

  1. Confirm that the DTC is not output again.


NEXT

END


← P0112 Intake Air Temperature Circuit Low Input (+ P0113) (from Jan 2012)P0116 Engine Coolant Temperature Circuit Range / Performance Problem (from Jan 2012) →