P0627 Fuel Pump Control Circuit / Open
Diagnostic trouble codes · Vehicles built from Jan 2012
Versions by build date: Sep 2011 – Dec 2011 from Jan 2012
DESCRIPTION
Refer to the System Description (Click here).| DTC Detection Drive Pattern |
DTC Detection Condition |
Trouble Area |
| Idling for 1 second |
Even though the CPU (command area inside ECU) is outputting the suction control valve operation duty, the output monitor signal is absent for 0.5 seconds (1 trip detection logic). |
|
| DTC No. |
Data List |
| P0627 |
Fuel Press |
- HINT:
- For more information on the fuel supply pump (suction control valve) and the common rail system, refer to the System Description (Click here).
- When DTC P0627 is stored, check the internal fuel pressure of the common rail by entering the following menus on the intelligent tester: Powertrain / Engine / Data List / Fuel Press.
Under a stable operating condition such as idling, Fuel Press is within +/-5 MPa of Target Common Rail Pressure.
- For more information on the fuel supply pump (suction control valve) and the common rail system, refer to the System Description (Click here).
WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).
- After replacing the fuel supply pump, the ECM needs initialization (Click here).
- After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).
- HINT:
- Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
| 1. INSPECT FUEL SUPPLY PUMP (SUCTION CONTROL VALVE) |
Disconnect the suction control valve connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
1 - 2
20°C (68°F)
1.9 to 2.3 Ω
|
|
||||
| OK | |
| 2. CHECK HARNESS AND CONNECTOR (SUCTION CONTROL VALVE - ECM) |
Disconnect the suction control valve connector.

Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance (Check for open):
for LHD Tester Connection
Condition
Specified Condition
z64-2 (PCV) - C45-105 (PCV-)
Always
Below 1 Ω
z64-1 (+B) - C45-106 (PCV+)
Always
Below 1 Ω
for RHD Tester Connection
Condition
Specified Condition
z64-2 (PCV) - C46-105 (PCV-)
Always
Below 1 Ω
z64-1 (+B) - C46-106 (PCV+)
Always
Below 1 Ω
- Standard Resistance (Check for short):
for LHD Tester Connection
Condition
Specified Condition
z64-2 (PCV) or C45-105 (PCV-) - Body ground
Always
10 kΩ or higher
z64-1 (+B) or C45-106 (PCV+) - Body ground
Always
10 kΩ or higher
for RHD Tester Connection
Condition
Specified Condition
z64-2 (PCV) or C46-105 (PCV-) - Body ground
Always
10 kΩ or higher
z64-1 (+B) or C46-106 (PCV+) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 3. CHECK WHETHER DTC OUTPUT RECURS |
Connect the intelligent tester to the DLC3
Turn the ignition switch to ON and turn the tester on.
Clear the DTCs (Click here).
Start the engine and idle it for 1 second.
Enter the following menus: Powertrain / Engine / DTC.
Read the DTCs.
Result Result
Proceed to
P0627 is output
A
No DTC is output
B
|
|
||||
|
|
||||
| 4. REPLACE FUEL SUPPLY PUMP |
Replace the fuel supply pump (Click here).
|
|
||||
| 5. REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
||||
| 6. REPLACE ECM |
Replace the ECM (Click here).
|
|
||||
| 7. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED |
Connect the intelligent tester to the DLC3.
Clear the DTCs (Click here).
Turn the ignition switch off.
Start the engine and idle it for 1 second.
Confirm that the DTC is not output again.
- HINT:
- Perform the following procedure using the tester to determine whether or not the DTC judgment has been carried out.
Enter the following menus: Powertrain / Engine / Utility / All Readiness.
Input DTC P0627.
Check that STATUS is NORMAL. If STATUS is INCOMPLETE or UNKNOWN, increase idling time.
| NEXT | ||
| ||
