2011-2013 Land Cruiser · Service Manual Drivetrain

REASSEMBLY

Removal / installation · Vehicles built from Sep 2011


1. INSTALL FRONT PROPELLER SHAFT UNIVERSAL JOINT SPIDER ASSEMBLY

  1. C060598E01
    Apply MP grease to a new spider and new bearings.

    NOTICE:
    Be careful not to apply too much grease.

  1. Fit the spider into the flange yoke.

  1. C115617E02
    Using SST, install the bearings to the spider.
    SST
    09332-25010  

  1. C175296
    Using SST, adjust both bearings so that the snap ring grooves are at maximum and equal in width.
    SST
    09332-25010  

  1. C175294
    Install 2 new snap rings of equal thickness which will allow 0 mm (0 in.) of axial play.

    HINT:
    Do not reuse the snap rings.

    Standard Snap Ring Thickness :
    Color
    Mark
    Specified Condition
    -
    J
    2.18 to 2.20 mm (0.0858 to 0.0866 in.)
    -
    K
    2.20 to 2.22 mm (0.0866 to 0.0874 in.)
    -
    F
    2.22 to 2.24 mm (0.0874 to 0.0882 in.)
    -
    G
    2.24 to 2.26 mm (0.0882 to 0.0890 in.)
    -
    H
    2.26 to 2.28 mm (0.0890 to 0.0898 in.)
    -
    1
    2.28 to 2.30 mm (0.0898 to 0.0906 in.)
    -
    2
    2.30 to 2.32 mm (0.0906 to 0.0913 in.)
    -
    -
    2.32 to 2.34 mm (0.0913 to 0.0921 in.)
    Brown
    -
    2.34 to 2.36 mm (0.0921 to 0.0929 in.)
    Blue
    -
    2.36 to 2.38 mm (0.0929 to 0.0937 in.)
    -
    6
    2.38 to 2.40 mm (0.0937 to 0.0945 in.)
    -
    7
    2.40 to 2.42 mm (0.0945 to 0.0953 in.)
    -
    8
    2.42 to 2.44 mm (0.0953 to 0.0961 in.)
    -
    C115795
    2.44 to 2.46 mm (0.0961 to 0.0969 in.)
    -
    10
    2.46 to 2.48 mm (0.0969 to 0.0976 in.)
    -
    A
    2.48 to 2.50 mm (0.0976 to 0.0984 in.)
    -
    B
    2.50 to 2.52 mm (0.0984 to 0.0992 in.)
    -
    C
    2.52 to 2.54 mm (0.0992 to 0.1000 in.)
    -
    D
    2.54 to 2.56 mm (0.1000 to 0.1008 in.)
    -
    E
    2.56 to 2.58 mm (0.1008 to 0.1016 in.)

  1. Using a hammer, tap the yoke until there is no clearance between the bearing outer race and snap ring.

  1. C172299E01
    Align the matchmarks on the propeller shaft and flange yoke or flange yoke and sleeve yoke.

  1. Install the flange yoke to the sleeve yoke or propeller shaft.

    HINT:
    Install 2 new spider bearings and snap rings on the flange yoke side using the procedure described above.


2. INSPECT PROPELLER SHAFT GREASE FITTING DIRECTION

HINT:
When replacing a spider bearing, be sure that the grease fitting hole is facing the direction shown in the illustration.


C174915E02

3. INSPECT SPIDER BEARING

NOTICE:
Be careful not to grip the propeller shaft tube too tightly in a vise as this will cause deformation.

  1. C172298
    Check the spider bearings for wear or damage.

  1. Check the spider bearing axial play by turning the yoke while holding the shaft tightly.

    Maximum bearing axial play:
    0 mm (0 in.)

    If the axial play is more than the maximum, replace the spider bearing.

← INSPECTION (from Sep 2011)INSTALLATION (Sep 2011 – Dec 2011) →