P2120 Throttle / Pedal Position Sensor / Switch "D" Circuit
Diagnostic trouble codes · Vehicles built Sep 2011 – Dec 2011
Also covers:
- P2122 Throttle / Pedal Position Sensor / Switch "D" Circuit Low Input
- P2123 Throttle / Pedal Position Sensor / Switch "D" Circuit High Input
- P2125 Throttle / Pedal Position Sensor / Switch "E" Circuit
- P2127 Throttle / Pedal Position Sensor / Switch "E" Circuit Low Input
- P2128 Throttle / Pedal Position Sensor / Switch "E" Circuit High Input
- P2138 Throttle / Pedal Position Sensor / Switch "D" / "E" Voltage Correlation
Versions by build date: Sep 2011 – Dec 2011 from Jan 2012
DESCRIPTION
- HINT:
- This is the repair procedure for the accelerator pedal position sensor.
- This electrical throttle system does not use a throttle cable.
- This accelerator pedal position sensor is a non-contact type.
- This is the repair procedure for the accelerator pedal position sensor.
In the accelerator pedal position sensor, the voltage applied to pedal terminals VPA and VPA2 of the ECM changes between 0 V and 5 V in proportion to the opening angle of the accelerator pedal. The VPA is a signal to indicate the actual accelerator pedal opening angle which is used for the engine control, and the VPA2 is a signal to indicate information about the opening angle which is used for detecting malfunctions. The ECM judges the current opening angle of the accelerator pedal using signals from terminals VPA and VPA2, and the ECM controls the throttle motor based on these signals.


| DTC Detection Drive Pattern |
DTC Detection Condition |
Trouble Area |
Ignition switch ON
|
Condition (a) continues for 0.5 seconds (1 trip detection logic): (a) VPA is less than 0.4 V and VPA2 is more than 0.97 deg, or VPA is more than 4.8 V. |
|
| DTC Detection Drive Pattern |
DTC Detection Condition |
Trouble Area |
Ignition switch ON
|
Condition (a) and (b) continue for 0.5 seconds (1 trip detection logic): (a) VPA is less than 0.4 V. (b) VPA2 is more than 0.97 deg. |
|
| DTC Detection Drive Pattern |
DTC Detection Condition |
Trouble Area |
Ignition switch ON
|
Condition (a) continues for 2.0 seconds (1 trip detection logic): (a) VPA is more than 4.8 V. |
|
| DTC Detection Drive Pattern |
DTC Detection Condition |
Trouble Area |
Ignition switch ON
|
Condition (a) continues for 0.5 seconds (1 trip detection logic): (a) VPA2 is less than 1.2 V and VPA is more than 2.7 deg, or VPA2 is more than 4.8 V and VPA is more than 0.4 V but less than 3.45 V. |
|
| DTC Detection Drive Pattern |
DTC Detection Condition |
Trouble Area |
Ignition switch ON
|
Condition (a) and (b) continue for 0.5 seconds (1 trip detection logic): (a) VPA2 is less than 1.2 V. (b) VPA2 is more than 2.7 deg. |
|
| DTC Detection Drive Pattern |
DTC Detection Condition |
Trouble Area |
Ignition switch ON
|
Conditions (a) and (b) continue for 2.0 seconds (1 trip detection logic): (a) VPA2 is more than 4.8 V. (b) VPA is more than 0.4 V but less than 3.45 V. |
|
| DTC Detection Drive Pattern |
DTC Detection Condition |
Trouble Area |
Ignition switch ON
|
Condition (a) or (b) continues for 2.0 seconds (1 trip detection logic): (a) The difference between VPA and VPA2 is less than 0.02 V. (b) VPA is less than 0.4 V and VPA2 is less than 1.2 V. |
|
| DTC No. |
Data List |
| P2120 |
|
| P2122 | |
| P2123 | |
| P2125 | |
| P2127 | |
| P2128 | |
| P2138 |
- HINT:
- When DTC P2120, P2122, P2123, P2125, P2127, P2128 and/or P2138 is stored, check the output voltage of the accelerator pedal position sensor by entering the following menus: Powertrain / Engine / Data List / Accel Sensor Out No.1 and Accel Sensor Out No.2.
Trouble Area
Accelerator Pedal Position Expressed as Voltage Output
Accelerator Pedal Released
Accelerator Pedal Depressed
Accel Sensor Out No.1
Accel Sensor Out No.2
Accel Sensor Out No.1
Accel Sensor Out No.2
VC circuit open
0 to 0.2 V
0 to 0.2 V
0 to 0.2 V
0 to 0.2 V
VPA circuit open or ground short
0 to 0.2 V
1.2 to 2.0 V
0 to 0.2 V
3.4 to 5.0 V
VPA2 circuit open or ground short
0.5 to 1.1 V
0 to 0.2 V
2.9 to 3.6 V
0 to 0.2 V
EPA circuit open
4.5 to 5.0 V
4.5 to 5.0 V
4.5 to 5.0 V
4.5 to 5.0 V
WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).
- HINT:
- Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
| 1. READ VALUE USING INTELLIGENT TESTER (ACCELERATOR PEDAL POSITION) |
Connect the intelligent tester to the DLC3.

Turn the ignition switch to ON and turn the tester on.
Enter the following menus: Powertrain / Engine / Data List / Accel Sens. No.1 Volt % and Accel Sens. No.2 Volt %.
Read the values.
- Standard:
Accelerator Pedal
Accel Sens. No.1 Volt %
Accel Sens. No.2 Volt %
Released
10 to 22%
24 to 40%
Depressed
52 to 90%
68 to 99%
Result Result
Proceed to
NG
A
OK
B
|
|
||||
| A | |
| 2. CHECK HARNESS AND CONNECTOR (ACCELERATOR PEDAL POSITION SENSOR - ECM) |
Disconnect the accelerator pedal position sensor connector.

Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance (Check for Open):
for LHD Tester Connection
Condition
Specified Condition
A31-1 (VCP2) - A38-56 (VCP2)
Always
Below 1 Ω
A31-2 (EPA2) - A38-58 (EPA2)
Always
Below 1 Ω
A31-3 (VPA2) - A38-54 (VPA2)
Always
Below 1 Ω
A31-4 (VCPA) - A38-55 (VCPA)
Always
Below 1 Ω
A31-5 (EPA) - A38-57 (EPA)
Always
Below 1 Ω
A31-6 (VPA) - A38-53 (VPA)
Always
Below 1 Ω
for RHD Tester Connection
Condition
Specified Condition
A31-1 (VCP2) - A52-56 (VCP2)
Always
Below 1 Ω
A31-2 (EPA2) - A52-58 (EPA2)
Always
Below 1 Ω
A31-3 (VPA2) - A52-54 (VPA2)
Always
Below 1 Ω
A31-4 (VCPA) - A52-55 (VCPA)
Always
Below 1 Ω
A31-5 (EPA) - A52-57 (EPA)
Always
Below 1 Ω
A31-6 (VPA) - A52-53 (VPA)
Always
Below 1 Ω
- Standard Resistance (Check for Short):
for LHD Tester Connection
Condition
Specified Condition
A31-1 (VCP2) or A38-56 (VCP2) - Body ground
Always
10 kΩ or higher
A31-2 (EPA2) or A38-58 (EPA2) - Body ground
Always
10 kΩ or higher
A31-3 (VPA2) or A38-54 (VPA2) - Body ground
Always
10 kΩ or higher
A31-4 (VCPA) or A38-55 (VCPA) - Body ground
Always
10 kΩ or higher
A31-5 (EPA) or A38-57 (EPA) - Body ground
Always
10 kΩ or higher
A31-6 (VPA) or A38-53 (VPA) - Body ground
Always
10 kΩ or higher
for RHD Tester Connection
Condition
Specified Condition
A31-1 (VCP2) or A52-56 (VCP2) - Body ground
Always
10 kΩ or higher
A31-2 (EPA2) or A52-58 (EPA2) - Body ground
Always
10 kΩ or higher
A31-3 (VPA2) or A52-54 (VPA2) - Body ground
Always
10 kΩ or higher
A31-4 (VCPA) or A52-55 (VCPA) - Body ground
Always
10 kΩ or higher
A31-5 (EPA) or A52-57 (EPA) - Body ground
Always
10 kΩ or higher
A31-6 (VPA) or A52-53 (VPA) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 3. INSPECT ECM TERMINAL VOLTAGE (VCPA AND VCP2 TERMINALS) |
Disconnect the accelerator pedal position sensor connector.

Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
A31-4 (VCPA) - A31-5 (EPA)
Ignition switch ON
4.5 to 5.5 V
A31-1 (VCP2) - A31-2 (EPA2)
Ignition switch ON
4.5 to 5.5 V
|
|
||||
| OK | |
| 4. REPLACE ACCELERATOR PEDAL ROD ASSEMBLY |
Replace the accelerator pedal rod assembly (Click here).
| NEXT | |
| 5. CHECK IF OUTPUT DTC RECURS |
Connect the intelligent tester to the DLC3.
Clear the DTC (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON.
Fully close the accelerator pedal for 3 seconds, then hold it partway open for 3 seconds, then fully open it for 3 seconds.
Read the DTCs.
Result Result
Proceed to
P2120, P2122, P2123, P2125, P2127, P2128 and/or P2138 are output again
A
No output
B
|
|
||||
| A | |
| 6. REPLACE ECM |
Replace the ECM (Click here).
|
|
||||
| 7. REPAIR OR REPLACE HARNESS OR CONNECTOR |
| NEXT | |
| 8. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED |
Connect the intelligent tester to the DLC3.
Clear the DTCs (Click here).
Turn the ignition switch off.
Turn the ignition switch off and leave the vehicle for 15 seconds.
Turn the ignition switch to ON.
Fully close the accelerator pedal for 3 seconds, then hold it partway open for 3 seconds, then fully open it for 3 seconds.
Confirm that the DTC is not output again.
- HINT:
- Perform the following procedure using the tester to determine whether or not the DTC judgment has been carried out.
Enter the following menus: Powertrain / Engine / Utility / All Readiness.
Input DTC P2120, P2122, P2123, P2125, P2127, P2128 and/or P2138.
Check that STATUS is NORMAL. If STATUS is INCOMPLETE or UNKNOWN, idle the engine.
| NEXT | ||
| ||
