REMOVAL
Removal / installation · Vehicles built Sep 2011 – Dec 2011
Versions by build date: Sep 2011 – Dec 2011 from Jan 2012
| 1.
DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
 |
- NOTICE:
- When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).
| 2.
REMOVE CENTER BACK DOOR GARNISH
|
 |
- Detach the 5 clips and 2 claws, and remove the back door garnish.
| 3.
REMOVE BACK DOOR SIDE GARNISH LH
|
 |
- Detach the 3 clips and remove the back door side garnish.
| 4.
REMOVE BACK DOOR SIDE GARNISH RH
|
 |
- HINT:
- Use the same procedures described for the LH side.
| 5.
REMOVE ASSIST GRIP (for Face to Face Seat Type)
|
 |
- Remove the 2 screws and assist grip.
| 6.
REMOVE NO. 2 BACK DOOR SERVICE HOLE COVER (for Face to Face Seat Type)
|
 |
- Using a screwdriver, detach the 4 claws and remove the back door service hole cover.
Disconnect connector.
| 7.
REMOVE POWER BACK DOOR MAIN SWITCH (for Face to Face Seat Type)
|
 |
- Detach the 2 claws and remove the power back door main switch.
| 8.
REMOVE BACK DOOR GARNISH
|
 |
Using a screwdriver, detach the 14 clips and remove the back door garnish.
- HINT:
- Tape the screwdriver tip before use.
| 9.
REMOVE BACK DOOR GLASS CHANNEL LH (w/ Rear Spoiler) |
 |
Using a clip remover, remove the clip.
Remove the back door glass channel LH.
| 10.
REMOVE BACK DOOR GLASS CHANNEL RH (w/ Rear Spoiler) |
 |
Using a clip remover, remove the clip.
Remove the back door glass channel RH.
| 11.
REMOVE REAR SPOILER SUB-ASSEMBLY (w/ Rear Spoiler)
|
 |
Remove the 4 bolts.
- Detach the 3 clips and remove the rear spoiler.
| 12.
REMOVE REAR WIPER ARM (w/ Rear Wiper)
|
 |
- Open the cover.
Remove the nut and rear wiper arm.
| 13.
REMOVE REAR WIPER MOTOR GROMMET (w/ Rear Wiper)
|
 |
- Detach the wiper motor grommet.
| 14.
REMOVE REAR WIPER MOTOR ASSEMBLY (w/ Rear Wiper)
|
 |
- Disconnect the connector.
Remove the 3 bolts and rear wiper motor assembly.
| 15.
REMOVE BACK WINDOW MOULDING OUTSIDE LH |
 |
Using a knife, cut off the moulding as shown in the illustration.
- NOTICE:
- Be careful not to damage the vehicle body.
Pull the shaded area shown in the illustration by the hand to remove the back window moulding outside.
- HINT:
- Make a partial cut in the moulding. Then pull and remove it by hand.
| 16.
REMOVE BACK WINDOW MOULDING OUTSIDE |
 |
Using a knife, cut off the moulding as shown in the illustration.
- NOTICE:
- Be careful not to damage the vehicle body.
Pull the shaded area shown in the illustration by the hand to remove the back window moulding outside.
- HINT:
- Make a partial cut in the moulding. Then pull and remove it by hand.
| 17.
REMOVE BACK WINDOW GLASS |
 |
- Apply protective tape to the outer surface of the vehicle body to prevent scratches.
- NOTICE:
- When separating the back window glass from the vehicle, be careful not to damage the vehicle paint or interior/exterior ornaments.
Disconnect the connectors.
- From the interior, insert a piano wire between the vehicle body and back window glass as shown in the illustration.
- NOTICE:
- Make sure not to damage the wire harness.
Tie objects that can serve as handles (for example, wooden blocks) to both wire ends.
- Place matchmarks over the glass and vehicle body on the locations indicated in the illustration.
- HINT:
- Matchmarks do not need to be placed if the glass is not going to be reused.
Cut through the adhesive by pulling the piano wire around the back window glass.
- NOTICE:
- Leave as much adhesive on the vehicle body as possible when removing the back window glass.
- Using suction cups, remove the back window glass.
| 18.
CLEAN VEHICLE BODY |
 |
Using a scraper, remove the moulding and adhesive from the back window glass.
Clean and shape the contact surface of the vehicle body.
On the contact surface of the vehicle body, use a knife to cut away excess adhesive as shown in the illustration.
- HINT:
- Leave as much adhesive on the vehicle body as possible.
- NOTICE:
- Be careful not to damage the vehicle body.
Clean the contact surface of the vehicle body with cleaner.
- HINT:
- Even if all the adhesive has been removed, clean the vehicle body.