2011-2013 Land Cruiser · Service Manual Vehicle Exterior

INSTALLATION

Removal / installation · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

HINT:
  1. Use the same procedures for the LH side and RH side.
  2. The procedures listed below are for the LH side.
  3. A bolt without a torque specification is shown in the standard bolt chart (Click here).


1. INSTALL QUARTER WINDOW ASSEMBLY

B180609E01
  1. Using a brush or sponge, apply primer M to the exposed part of the vehicle body.

    NOTICE:
    1. Allow the primer coating to dry for 3 minutes or more.
    2. Throw away any leftover primer.
    3. Do not apply too much primer.

  1. Using a brush or sponge, apply Primer G to the contact surface of the glass.

    B185866E01

    Standard:
    Area
    Specified Condition
    a
    6.8 mm (0.268 in.)
    b
    6.5 mm (0.256 in.)
    c
    6.7 mm (0.264 in.)

    HINT:
    If primer is applied to an area that is not specified, wipe off the primer with non-residue solvent before it dries.

    NOTICE:
    1. Allow the primer to dry for 3 minutes or more.
    2. Throw away any leftover primer.
    3. Do not apply too much primer.

  1. Apply adhesive to the quarter window glass.

    Adhesive:
    Toyota Genuine Windshield Glass Adhesive or equivalent


    1. Cut off the tip of the cartridge nozzle as shown in the illustration.

      B185870E01

      Standard:
      Area
      Specified Condition
      a
      12.0 mm (0.472 in.)
      b
      8.0 mm (0.315 in.)
      c
      6.8 mm (0.268 in.)
      d
      6.5 mm (0.256 in.)
      e
      6.7 mm (0.264 in.)

      HINT:
      After cutting off the tip, use all adhesive within the time written in the table below.

      Usage Time Frame:
      Temperature
      Usage Time Frame
      35°C (95°F)
      15 minutes
      20°C (68°F)
      1 hour 40 minutes
      5°C (41°F)
      8 hours

    2. Load the sealer gun with the cartridge.

    3. Apply adhesive to the quarter window glass as shown in the illustration.

  1. Install the quarter window glass to the vehicle body.

    1. Hold the quarter window glass in place securely with protective tape or equivalent until the adhesive hardens.

      NOTICE:
      1. Allow the primer coating to dry for 3 minutes or more.
      2. Check the clearance between the body and glass.

    2. Lightly press the front surface of the glass to ensure a close fit.

    3. BO03986E05
      Using a scraper, remove any excess or protruding adhesive.

      HINT:
      Apply adhesive onto the glass rim.

      NOTICE:
      Do not drive the vehicle within the time written in the table below.

      Minimum Time:
      Temperature
      Minimum Time Prior to Driving Vehicle
      35°C (95°F)
      1 hour 30 minutes
      20°C (68°F)
      5 hours
      5°C (41°F)
      24 hours

  1. Connect the connectors.


2. CHECK FOR LEAKS AND REPAIR
  1. Conduct a leak test after the adhesive has completely hardened.

  1. Seal any leaks with auto glass sealer.


3. INSTALL ROOF HEADLINING ASSEMBLY (w/o Sliding Roof)
  1. Install the roof headlining (Click here).


4. INSTALL ROOF HEADLINING ASSEMBLY (w/ Sliding Roof)
  1. Install the roof headlining (Click here).

← REMOVAL (from Jan 2012)INSTALLATION (from Jan 2012) →