2011-2013 Land Cruiser · Service Manual Vehicle Interior

INSTALLATION

Removal / installation · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

HINT:
A bolt without a torque specification is shown in the standard bolt chart (Click here).


1. INSTALL SIDE TRIM BOX

B185343
  1. Install the side trim box with the 9 screws.


2. INSTALL SIDE TRIM BOX COVER
  1. Install the side trim box cover.


3. INSTALL QUARTER TRIM LID SUB-ASSEMBLY RH
  1. Install the quarter trim lid.


4. INSTALL QUARTER TRIM COVER LH (w/o Rear No. 2 Seat, w/ Rear No. 2 Seat for Face to Face Seat Type)

B188391
  1. Attach the 6 clips to install the quarter trim cover.


5. INSTALL QUARTER TRIM COVER RH (w/o Rear No. 2 Seat, w/ Rear No. 2 Seat for Face to Face Seat Type)

HINT:
Use the same procedures described for the LH side.


6. INSTALL REAR NO. 2 SEAT COVER BEZEL (w/ Rear No. 2 Seat, except Face to Face Seat Type)

B181698
  1. Attach the 6 clips to install the rear No. 2 seat cover bezel.


7. INSTALL REAR NO. 1 SEAT COVER BEZEL (w/ Rear No. 2 Seat, except Face to Face Seat Type)

HINT:
Use the same procedures described for the rear No. 2 seat cover bezel.


8. INSTALL REAR SEAT LOCK CONTROL LEVER SUB-ASSEMBLY LH (w/ Rear No. 2 Seat, except Face to Face Seat Type)
  1. Attach the 4 claws to install the seat lock control lever.


9. INSTALL REAR SEAT LOCK CONTROL LEVER SUB-ASSEMBLY RH (w/ Rear No. 2 Seat, except Face to Face Seat Type)

HINT:
Use the same procedures described for the LH side.


10. INSTALL NO. 2 SIDE TRIM BASE COVER LH (w/ Rear Heater)

B182421
  1. Attach the 4 claws to install the cover.


11. INSTALL NO. 2 SIDE TRIM BASE COVER RH (w/ Rear Heater)

HINT:
Use the same procedures described for the LH side.


12. INSTALL NO. 1 SIDE TRIM BASE COVER LH (w/ Rear Heater)

B182420
  1. Attach the 4 claws to install the cover.


13. INSTALL NO. 1 SIDE TRIM BASE COVER RH (w/ Rear Heater)

B187176
  1. Attach the 4 claws to install the cover.

  1. B185344
    Install the duct with the 6 screws.


14. INSTALL NO. 2 CUP HOLDER

B182417
  1. Attach the 3 claws to install the cup holder.

  1. Install the 5 screws.


15. INSTALL NO. 1 CUP HOLDER

B182419
  1. Attach the 3 claws to install the cup holder.

  1. Install the 5 screws.


16. INSTALL QUARTER TRIM COVER SUB-ASSEMBLY LH

B182415
  1. Attach the 4 claws to install the quarter trim cover.

  1. Install the 7 screws.

  1. B182411
    w/ Rear Heater:
    Install the duct with the 8 screws.


17. INSTALL QUARTER TRIM COVER SUB-ASSEMBLY RH

B182413
  1. Attach the 4 claws to install the quarter trim cover.

  1. Install the 7 screws.


18. INSTALL REAR NO. 2 SEAT SHOULDER BELT HANGER LH

B182422E01
  1. Install the hanger with 2 new spring nuts.


19. INSTALL REAR NO. 2 SEAT SHOULDER BELT HANGER RH

HINT:
Use the same procedures described for the LH side.


20. INSTALL REAR SEAT SHOULDER BELT HANGER (w/ Rear No. 2 Seat, except Face to Face Seat Type)

B182426E01

HINT:
Use the same procedure to install the hanger on the other side.

  1. Install the hanger with 2 new spring nuts.


21. INSTALL ROOF SIDE INNER GARNISH COVER LH (w/ Rear No. 2 Seat, except Face to Face Seat Type)

B182427
  1. Attach the 7 claws to install the cover.


22. INSTALL ROOF SIDE INNER GARNISH COVER RH (w/ Rear No. 2 Seat, except Face to Face Seat Type)

HINT:
Use the same procedures described for the LH side.


23. INSTALL REAR SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY LH

B182423
  1. Attach the 6 claws to install the plate.


24. INSTALL REAR SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY RH

HINT:
Use the same procedures described for the LH side.


25. INSTALL FRONT SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY LH

B182425
  1. Slide the plate in the direction shown in the illustration and attach the 6 claws to install the plate.


26. INSTALL FRONT SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY RH

HINT:
Use the same procedures described for the LH side.


27. INSTALL REAR DOOR SCUFF PLATE OUTSIDE LH

B181675
  1. Attach the 3 clips to install the rear door scuff plate outside.


28. INSTALL REAR DOOR SCUFF PLATE OUTSIDE RH

HINT:
Use the same procedures described for the LH side.


29. INSTALL FRONT DOOR SCUFF PLATE OUTSIDE LH

B181683
  1. Attach the 4 clips to install the front door scuff plate outside.


30. INSTALL FRONT DOOR SCUFF PLATE RH

HINT:
Use the same procedures described for the LH side.


31. INSTALL BACK DOOR WEATHERSTRIP

B190021E01
  1. Install the back door weatherstrip as shown in the illustration.


32. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH

B182482E01
  1. Install the rear door opening trim weatherstrip as shown in the illustration.


33. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH

HINT:
Use the same procedures described for the LH side.


34. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH

B182480E01
  1. Install the front door opening trim weatherstrip as shown in the illustration.


35. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH

HINT:
Use the same procedures described for the LH side.


36. INSTALL ROOF HEADLINING ASSEMBLY

B183934

HINT:
  1. for Manual Seat:
    When installing the roof headlining, move the front seat and rear No. 1 seat to the position shown in the illustration.
  2. for Power Seat:
    When installing the roof headlining, connect the cable to the negative (-) battery terminal and move the front seat and No. 1 rear seat to the position shown in the illustration.
  3. for Power Seat:
    After moving the seats, disconnect the cable from the negative (-) battery terminal.

  1. B181716
    Place the headlining in the cabin from the rear of the vehicle as shown in the illustration.

    NOTICE:
    Be careful not to damage the roof headlining when placing it in the cabin.

  1. for 3 Person Seat Type Rear No. 2 Seat:
    Attach the 12 claws, 2 clips, 2 guides and 16 fasteners to install the headlining.

    B188366E01

  1. except 3 Person Seat Type Rear No. 2 Seat:
    Attach the 12 claws, 3 clips, 2 guides and 16 fasteners to install the headlining.

    B188367E01

  1. B181721E01
    Connect the washer hose.

  1. B181720E01
    Connect the antenna cord connector.

  1. B181718E01
    Connect the antenna cord connector and attach the 2 clamps.

  1. Install the bolt.

  1. B181719E01
    Connect the 3 roof wire connectors and washer hose.

  1. Attach the 4 clamps.

  1. B181722
    Connect the drive gear connector.

  1. B186952
    w/ Rain Sensor:
    Disconnect the rain sensor connector.

  1. B183869
    w/ EC Mirror:
    Connect the inner mirror connector.


37. INSTALL FRONT ROOF SIDE RAIL GARNISH LH

B182429E01
  1. Install 3 new clips to the roof side rail garnish.

  1. Attach the 3 clips to install the roof side rail garnish.


38. INSTALL FRONT ROOF SIDE RAIL GARNISH RH

HINT:
Use the same procedures described for the LH side.


39. INSTALL 3RD SEAT ASSIST GRIP ASSEMBLY (w/ Rear No. 2 Seat, except Face to Face Seat Type)

B165740

HINT:
Use the same procedure to install the 3rd seat assist grip on the other side.

  1. Assemble the assist grip, 2 clips and 2 covers as shown in the illustration.

  1. Install the assist grip.


40. INSTALL NO. 2 ASSIST GRIP ASSEMBLY LH

B169217
  1. w/ Rear No. 2 Seat, except Face to Face Seat Type or w/o Rear No. 2 Seat:
    Install the No. 2 assist grip assembly.

    1. Assemble the assist grip, 2 clips and 2 covers as shown in the illustration.

    2. Install the assist grip.

  1. B165740
    w/ Rear No. 2 Seat, for Face to Face Seat Type:
    Install the No. 2 assist grip assembly.

    1. Assemble the assist grip, 2 clips and 2 covers as shown in the illustration.

    2. Install the assist grip.


41. INSTALL NO. 2 ASSIST GRIP ASSEMBLY RH

HINT:
Use the same procedures described for the LH side.


42. INSTALL ASSIST GRIP ASSEMBLY

B165740

HINT:
Use the same procedure to install the assist grip on the other side.

  1. Assemble the assist grip, 2 clips and 2 covers as shown in the illustration.

  1. Install the assist grip.


43. INSTALL SEAT BELT ANCHOR COVER (for 3 Person Seat Type Rear No. 2 Seat)

B181709
  1. Attach the 4 guides and 4 clips to install the seat belt anchor cover.


44. INSTALL RAIN SENSOR COVER (w/ Rain Sensor)

  1. Push in the stopper in the direction of the arrow labeled (1) to install the rain sensor cover.

    E160055E01

  1. Slide the No. 2 cover in the direction of the arrow labeled (2) to fix it in place.


45. INSTALL INNER REAR VIEW MIRROR STAY HOLDER COVER (w/ EC Mirror)

B180557
  1. Attach the 2 claws to install the cover.


46. INSTALL CENTER VISOR ASSEMBLY LH (w/ Sub Visor)

B189887
  1. Attach the 2 clips to install the center visor.


47. INSTALL CENTER VISOR ASSEMBLY RH (w/ Sub Visor)

HINT:
Use the same procedures described for the LH side.


48. INSTALL VISOR HOLDER

B151383

HINT:
Use the same procedures to install the visor holder on the other side.

  1. Attach the 2 claws.

  1. Push the visor holder in to install it.


49. INSTALL VISOR ASSEMBLY LH

B181707
  1. Install the visor with the 2 screws.


50. INSTALL VISOR ASSEMBLY RH

HINT:
Use the same procedures described for the LH side.


51. INSTALL VISOR BRACKET COVER

B181706

HINT:
Use the same procedure to install the visor bracket cover on the other side.

  1. Attach the 4 claws to install the visor bracket cover.


52. INSTALL NO. 2 ROOM LIGHT ASSEMBLY

B181712
  1. Install the 2 covers.

  1. B183997
    Attach the 4 claws to install the room light lens.

  1. B183867E01
    Attach the 4 claws to install the room light to the room light switch base.

  1. B183998
    Attach the 4 claws to install the room light.


53. INSTALL NO. 1 ROOM LIGHT ASSEMBLY

B181717
  1. Connect the connector.

  1. Attach the 4 clips to install the room light.


54. INSTALL MAP LIGHT ASSEMBLY
  1. Connect the connector.

  1. Attach the 2 clips and 2 guides to install the map light.

  1. Install the 2 screws.

  1. Attach the 2 claws to close the 2 covers.

    B181714


55. INSTALL REAR UPPER PILLAR GARNISH LH

B181702
  1. Attach the 5 clips to install the rear upper pillar garnish.

  1. B183809
    w/ Rear No. 2 Seat, except Face to Face Seat Type:

    1. Install the seat belt shoulder anchor with the bolt.

      Torque:
      42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    2. B183996
      Attach the 2 claws to close the seat belt shoulder anchor cover.


56. INSTALL REAR UPPER PILLAR GARNISH RH

HINT:
Use the same procedures described for the LH side.


57. INSTALL REAR FRONT QUARTER TRIM GARNISH LH

B181703
  1. Pass the seat belt anchor through the quarter trim garnish.

  1. Attach the clip and 2 guides to install the quarter trim garnish.

  1. Install the screw.


58. INSTALL REAR FRONT QUARTER TRIM GARNISH RH

HINT:
Use the same procedures described for the LH side.


59. INSTALL FRONT QUARTER TRIM PANEL ASSEMBLY LH

B182644

HINT:
When installing the front quarter trim panel, operate the reclining adjuster release handle and move the No. 1 rear seat to the position shown in the illustration.

  1. w/ Rear No. 2 Seat, except Face to Face Seat Type:

    1. w/o Rear Air Conditioning System:
      Connect the rear seat lock control lever cable.

    2. w/ Rear Air Conditioning System:
      Connect the thermistor connector and rear seat lock control lever cable.

    3. Attach the 18 clips and 2 claws to install the quarter trim panel.

    4. Install the clip and bolt.

      Torque:
      12 N*m{ 122 kgf*cm , 9 ft.*lbf }


      B186889

  1. w/o Rear No. 2 Seat or w/ Rear No. 2 Seat, for Face to Face Seat Type:

    1. Attach the 18 clips and 2 claws to install the quarter trim panel.

    2. Install the clip.

      B190221

  1. B181691E02
    w/ Rear No. 2 Seat, except Face to Face Seat Type:
    Install the rear No. 2 seat belt anchor with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    NOTICE:
    Do not overlap the anchor part of the seat belt and protruding parts of the vehicle body.

  1. B181689
    Install the rear No. 1 seat belt anchor with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

  1. B181687
    Attach the 3 claws to install the cover.


60. INSTALL FRONT QUARTER TRIM PANEL ASSEMBLY RH

B182645

HINT:
When installing the front quarter trim panel, operate the reclining adjuster release handle and move the No. 1 rear seat to the position shown in the illustration.

  1. w/ Rear No. 2 Seat, except Face to Face Seat Type:

    1. w/o Rear Air Conditioning System:
      Connect the rear seat lock control lever cable.

    2. w/ Rear Air Conditioning System:
      Connect the thermistor connector and rear seat lock control lever cable.

    3. Attach the 16 clips and 2 claws to install the quarter trim panel.

    4. Install the clip and bolt.

      Torque:
      12 N*m{ 122 kgf*cm , 9 ft.*lbf }


      B186890

  1. w/o Rear No. 2 Seat or w/ Rear No. 2 Seat, for Face to Face Seat Type:

    1. Attach the 16 clips and 2 claws to install the quarter trim panel.

    2. Install the clip.

      B190220

  1. B181693
    w/ Rear No. 2 Seat, except Face to Face Seat Type:

    1. Install the rear No. 2 seat belt anchor with the bolt.

      Torque:
      42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    2. B181692
      Attach the 3 claws to install the cover.

  1. B181690
    Install the rear No. 1 seat belt anchor with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

  1. B181688
    Attach the 3 claws to install the cover.


61. INSTALL REAR SEAT COVER CAP (w/ Rear No. 2 Seat, except Face to Face Seat Type)

B190214

HINT:
Use the same procedure to install the rear seat cover cap on the other side.

  1. Attach the 3 claws to install the rear seat cover cap.


62. INSTALL CENTER PILLAR GARNISH LH

B181681
  1. Pass the seat belt anchor through the center pillar garnish.

  1. Attach the 2 clips and 2 guides to install the center pillar garnish.

  1. Install the bolt.


63. INSTALL CENTER PILLAR GARNISH RH

HINT:
Use the same procedures described for the LH side.


64. INSTALL REAR ASSIST GRIP ASSEMBLY

B181680

HINT:
Use the same procedure to install the rear assist grip on the other side.

  1. Attach the 2 claws to install the rear assist grip.

  1. Install the 2 bolts.

  1. B181679
    Attach the 4 claws to install the 2 assist grip plugs.


65. INSTALL CENTER LOWER PILLAR GARNISH LH

HINT:
  1. for Manual Seat:
    When installing the center lower pillar garnish, move the front seat and seatback to the foremost upright position.
  2. for Power Seat:
    When installing the center lower pillar garnish, connect the cable to the negative (-) battery terminal and operate the power seat switch to move the front seat and seatback to the foremost upright position.
  3. for Power Seat:
    After moving the front seat, disconnect the cable from the negative (-) battery terminal.

  1. B181678
    Attach the 2 claws and 7 clips to install the center lower pillar garnish.

  1. B181677
    Install the seat belt anchor with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }


66. INSTALL CENTER LOWER PILLAR GARNISH RH

HINT:
Use the same procedures described for the LH side.


67. INSTALL CENTER PILLAR GARNISH COVER LH

HINT:
  1. for Manual Seat:
    When installing the center pillar garnish cover, move the front seat and seatback to the foremost upright position.
  2. for Power Seat:
    When installing the center pillar garnish cover, connect the cable to the negative (-) battery terminal and operate the power seat switch to move the front seat and seatback to the foremost upright position.
  3. for Power Seat:
    After moving the front seat, disconnect the cable from the negative (-) battery terminal.

  1. B181676
    Attach the 2 clips and 2 guides to install the cover.


68. INSTALL CENTER PILLAR GARNISH COVER RH

HINT:
Use the same procedures described for the LH side.


69. INSTALL FRONT PILLAR GARNISH LH

B185447
  1. for 9, 14 Speakers:
    Connect the speaker connector.

  1. Attach the clip and 3 guides to install the front pillar garnish.


70. INSTALL FRONT PILLAR GARNISH RH

HINT:
Use the same procedures described for the LH side.


71. INSTALL FRONT ASSIST GRIP SUB-ASSEMBLY

B181685

HINT:
Use the same procedure to install the front assist grip on the other side.

  1. Attach the 2 claws to install the front assist grip.

  1. Install the 2 bolts.

  1. B181684
    Attach the 4 claws to install the 2 assist grip plugs.


72. INSTALL REAR FLOOR MAT REAR SUPPORT PLATE

B181672
  1. Attach the 6 clips to install the support plate.


73. INSTALL REAR DOOR SCUFF PLATE LH

B181674
  1. Attach the 3 claws and 4 clips to install the scuff plate.

  1. Install the screw.


74. INSTALL REAR DOOR SCUFF PLATE RH

HINT:
Use the same procedures described for the LH side.


75. INSTALL REAR STEP COVER

B181673

HINT:
Use the same procedure to install the step cover on the other side.

  1. Attach the 2 claws to install the step cover.


76. INSTALL FRONT DOOR SCUFF PLATE LH

B181682
  1. Attach the 7 claws and 4 clips to install the scuff plate.


77. INSTALL FRONT DOOR SCUFF PLATE RH

HINT:
Use the same procedures described for the LH side.


78. INSTALL REAR NO. 2 SEAT ASSEMBLY LH (except Face to Face Seat Type)
  1. Install the rear No. 2 seat assembly LH (Click here).


79. INSTALL REAR NO. 2 SEAT ASSEMBLY RH (except Face to Face Seat Type)

HINT:
Use the same procedures described for the LH side.


80. INSTALL REAR NO. 2 SEAT ASSEMBLY LH (for Face to Face Seat Type)
  1. Install the rear No. 2 seat assembly LH (Click here).


81. INSTALL REAR NO. 2 SEAT ASSEMBLY RH (for Face to Face Seat Type)

HINT:
Use the same procedures described for the LH side.


82. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

← REASSEMBLY (from Jan 2012)INSTALLATION (from Jan 2012) →