SERVICE DATA
Specifications · Vehicles built Sep 2011 – Dec 2011
Versions by build date: Sep 2011 – Dec 2011 from Jan 2012
| Starter assembly |
No-load characteristics current |
200 A or less at 11 V |
|
| Starter armature assembly |
Standard resistance |
Commutator |
Below 1 Ω |
| Commutator - Armature coil core |
10 kΩ or higher |
||
| Maximum circle runout |
0.05 mm (0.00197 in.) |
||
| Standard commutator diameter |
36.0 mm (1.42 in.) |
||
| Minimum commutator diameter |
35.0 mm (1.38 in.) |
||
| Standard undercut depth |
0.7 mm (0.0276 in.) |
||
| Minimum undercut depth |
0.2 mm (0.00787 in.) |
||
| Starter yoke assembly |
Standard resistance |
Terminal C plate - Brushes |
Below 1 Ω |
| Brushes - Starter yoke body |
10 kΩ or higher |
||
| Brush length |
Standard length |
21.0 mm (0.827 in.) |
|
| Minimum length |
12.0 mm (0.472 in.) |
||
| Starter brush holder assembly |
Standard resistance |
Positive (+) brush holder - Negative (-) brush holder |
10 kΩ or higher |
| Brush spring |
Standard spring installed load |
36 N (3.6 kgf, 8.0 lbf) |
|
| Minimum spring installed load |
12 N (1.2 kgf, 2.7 lbf) |
||
| Magnet starter switch assembly |
Standard resistance |
Terminal 50 - Terminal C |
Below 0.3 Ω |
| Terminal 50 - Housing body |
Below 0.8 Ω |
||
| Glow plug |
Standard resistance |
Glow plug terminal - Body ground |
Approximately 1 Ω at 20°C (68°F) |
| Starter relay |
Standard resistance |
3 - 5 |
10 kΩ or higher (Battery voltage is not applied to terminals 1 and 2) |
| Below 1 Ω (Battery voltage is applied to terminals 1 and 2) | |||
| Starter cut relay |
Standard resistance |
3 - 5 |
10 kΩ or higher (Battery voltage is not applied to terminals 1 and 2) |
| Below 1 Ω (Battery voltage is applied to terminals 1 and 2) | |||
| ACC relay (Main body ECU) |
Standard resistance |
2A-1 - 2D-8 |
10 kΩ or higher (Battery voltage is not applied between 2D-45 and 2D-62) |
| Below 1 Ω (Battery voltage is applied between 2D-45 and 2D-62) | |||
| No. 1 glow relay |
Standard resistance |
3 - 5 |
10 kΩ or higher (Battery voltage is not applied to terminals 1 and 2) |
| Below 1 Ω (Battery voltage is applied to terminals 1 and 2) | |||
| No. 2 Glow relay |
Standard resistance |
3 - 5 |
10 kΩ or higher (Battery voltage is not applied to terminals 1 and 2) |
| Below 1 Ω (Battery voltage is applied to terminals 1 and 2) | |||
| Engine switch |
Standard resistance |
7 - 5 |
Below 1 Ω (Engine switch is pushed) |
| 2 - 5 |
Below 1 Ω (Engine switch is pushed) |
||
| 7 - 5 |
10 kΩ or higher (Engine switch is not pushed) |
||
| 2 - 5 |
10 kΩ or higher (Engine switch is not pushed) |
||
| ignition switch |
Standard resistance |
All combinations of all terminals |
10 kΩ or higher (LOCK) |
| 4 (AM1) - 2 (ACC) |
Below 1 Ω (ACC) |
||
| 4 (AM1) - 2 (ACC) 4 (AM1) - 1 (IG1) 5 (AM2) - 6 (IG2) |
Below 1 Ω (ON) |
||
| 4 (AM1) - 1 (IG1) 4 (AM1) - 3 (ST1) 5 (AM2) - 6 (IG2) |
Below 1 Ω (START) |
||