2011-2013 Land Cruiser · Service Manual General

SERVICE DATA

Specifications · Vehicles built from Jan 2012

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

Starter assembly
No-load characteristics current
200 A or less at 11 V
Starter armature assembly
Standard resistance
Commutator
Below 1 Ω
Commutator - Armature coil core
10 kΩ or higher
Maximum circle runout
0.05 mm (0.00197 in.)
Standard commutator diameter
36.0 mm (1.42 in.)
Minimum commutator diameter
35.0 mm (1.38 in.)
Standard undercut depth
0.7 mm (0.0276 in.)
Minimum undercut depth
0.2 mm (0.00787 in.)
Starter yoke assembly
Standard resistance
Terminal C plate - Brushes
Below 1 Ω
Brushes - Starter yoke body
10 kΩ or higher
Brush length
Standard length
21.0 mm (0.827 in.)
Minimum length
12.0 mm (0.472 in.)
Starter brush holder assembly
Standard resistance
Positive (+) brush holder - Negative (-) brush holder
10 kΩ or higher
Brush spring
Standard spring installed load
36 N (3.6 kgf, 8.0 lbf)
Minimum spring installed load
12 N (1.2 kgf, 2.7 lbf)
Magnet starter switch assembly
Standard resistance
Terminal 50 - Terminal C
Below 0.3 Ω
Terminal 50 - Housing body
Below 0.8 Ω
Glow plug
Standard resistance
w/o DPF
Glow plug terminal - Body ground
Approximately 1 Ω at 20°C (68°F)
Standard resistance
w/ DPF
0.7 Ω or higher at 20°C (68°F)
Starter relay
Standard resistance
3 - 5
10 kΩ or higher (Battery voltage is not applied to terminals 1 and 2)
Below 1 Ω (Battery voltage is applied to terminals 1 and 2)
Starter cut relay
Standard resistance
3 - 5
10 kΩ or higher (Battery voltage is not applied to terminals 1 and 2)
Below 1 Ω (Battery voltage is applied to terminals 1 and 2)
ACC relay
(Main body ECU)
Standard resistance
2A-1 - 2D-8
10 kΩ or higher (Battery voltage is not applied between 2D-45 and 2D-62)
Below 1 Ω (Battery voltage is applied between 2D-45 and 2D-62)
No. 1 glow relay
Standard resistance
3 - 5
10 kΩ or higher (Battery voltage is not applied to terminals 1 and 2)
Below 1 Ω (Battery voltage is applied to terminals 1 and 2)
No. 2 Glow relay
Standard resistance
3 - 5
10 kΩ or higher (Battery voltage is not applied to terminals 1 and 2)
Below 1 Ω (Battery voltage is applied to terminals 1 and 2)
Engine switch
Standard resistance
7 - 5
Below 1 Ω (Engine switch is pushed)
2 - 5
Below 1 Ω (Engine switch is pushed)
7 - 5
10 kΩ or higher (Engine switch is not pushed)
2 - 5
10 kΩ or higher (Engine switch is not pushed)
ignition switch
Standard resistance
All combinations of all terminals
10 kΩ or higher (LOCK)
4 (AM1) - 2 (ACC)
Below 1 Ω (ACC)
4 (AM1) - 2 (ACC)
4 (AM1) - 1 (IG1)
5 (AM2) - 6 (IG2)
Below 1 Ω (ON)
4 (AM1) - 1 (IG1)
4 (AM1) - 3 (ST1)
5 (AM2) - 6 (IG2)
Below 1 Ω (START)
← SERVICE DATA (Sep 2011 – Dec 2011)TORQUE SPECIFICATIONS (Sep 2011 – Dec 2011) →