2011-2013 Land Cruiser · Service Manual Steering

REASSEMBLY

Removal / installation · Vehicles built from Sep 2011

NOTICE:
When installing parts, coat the parts indicated by arrows with power steering fluid (Click here).


1. INSTALL VANE PUMP HOUSING OIL SEAL

  1. C114702E01
    Coat the lip of a new oil seal with power steering fluid.

  1. Using SST and a press, press in the oil seal.

    SST
    09950-60010   (09951-00280)
    09950-70010   (09951-07100)

    NOTICE:
    Make sure that the oil seal is installed facing in the correct direction as shown in the illustration.


2. INSTALL VANE PUMP SHAFT WITH VANE PUMP PULLEY

  1. C114703E01
    Coat the inside surface of the bushing in the vane pump front housing with power steering fluid.

  1. Gradually insert the vane pump shaft with vane pump pulley.

    NOTICE:
    1. Do not damage the lip of the oil seal in the front housing.
    2. Wrap protective tape around the spline of the vane pump shaft with vane pump pulley in order to prevent damage to the oil seal.


3. INSTALL VANE PUMP FRONT SIDE PLATE

  1. C132035
    Coat a new O-ring with power steering fluid and install it into the front housing.

  1. C107035
    Coat a new O-ring with power steering fluid and install it onto the front side plate.

  1. C132040E01
    Align the notch of the front side plate with the notch of the front housing, and install the front side plate.

    NOTICE:
    Make sure that the front side plate is installed facing in the correct direction.


4. INSTALL VANE PUMP CAM RING

  1. C139139E01
    Align the notch of the cam ring with the notch of the front side plate, and install the cam ring with the inscribed mark facing upward.

    NOTICE:
    Make sure that the cam ring is installed facing in the correct direction.


5. INSTALL VANE PUMP ROTOR

  1. C107038
    Install the vane pump rotor.

    HINT:
    The vane pump rotor can be installed in both directions.

  1. Coat the 10 vane pump plates with power steering fluid.

  1. C141370E01
    Install the vane pump plates with the round end facing outward.

    NOTICE:
    Make sure that the vane pump plates are installed facing in the correct direction.


6. INSTALL VANE PUMP SHAFT SNAP RING

  1. D030336E01
    Using a screwdriver and snap ring expander, install a new shaft snap ring onto the vane pump shaft.

    NOTICE:
    1. Do not expand the shaft snap ring any further than needed.
    2. Make sure that the shaft snap ring is completely fit into the groove.
    3. Do not damage the vane pump rotor and shaft.


7. INSTALL VANE PUMP REAR HOUSING

  1. C107040
    Coat a new O-ring with power steering fluid and install it onto the rear housing.

  1. C136780E01
    Align the straight pin of the rear housing with the notches of the cam ring, front side plate, and front housing.

    NOTICE:
    Make sure that the O-ring is not protruding anywhere when installing the vane pump rear housing.

  1. C107024
    Install the rear housing with the 4 bolts.

    Torque:
    22 N*m{ 224 kgf*cm , 16 ft.*lbf }


8. INSPECT TOTAL PRELOAD
  1. Check that the pump rotates smoothly without abnormal noise.

  1. Temporarily install a service bolt.

    Recommended service bolt:
    Thread diameter:
    10 mm (0.394 in.)
    Thread pitch:
    1.25 mm (0.0492 in.)
    Bolt length:
    50 mm (1.97 in.)

  1. C053369E10
    Using a torque wrench, measure the pump rotating torque.

    Standard rotating torque:
    0.3 N*m (3 kgf*cm, 2 in.*lbf) or less

    If the rotating torque is not as specified, check the vane pump housing oil seal.


9. INSTALL FLOW CONTROL VALVE ASSEMBLY

  1. C158958
    Coat the flow control valve with power steering fluid.

  1. Install the compression spring and flow control valve to the front housing.

    NOTICE:
    Do not mistake the direction of the control valve.

  1. Coat a new O-ring with power steering fluid and install it onto the pressure port union.

  1. Install the pressure port union to the front housing.

    Torque:
    69 N*m{ 704 kgf*cm , 51 ft.*lbf }


10. FIX VANE PUMP ASSEMBLY

C158820E01
  1. Using SST, fix the vane pump in a vise.

    SST
    09630-00014   (09631-00132)


11. INSTALL POWER STEERING SUCTION PORT UNION
  1. Coat a new O-ring with power steering fluid and install it to the suction port union.

  1. C158821
    Install the suction port union to the vane pump with the bolt.

    Torque:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }

← INSPECTION (from Sep 2011)INSTALLATION (Sep 2011 – Dec 2011) →