2011-2013 Land Cruiser · Service Manual Brake

INSTALLATION

Removal / installation · Vehicles built from Jan 2012

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012


1. INSTALL FRONT SPEED SENSOR LH

  1. C271342
    Install the speed sensor with the bolt.

    Torque:
    8.5 N*m{ 87 kgf*cm , 75 in.*lbf }

    NOTICE:
    1. Make sure there are no pieces of iron or other foreign matter attached to the sensor tip.
    2. While inserting the speed sensor into the knuckle hole, do not strike or damage the sensor tip.
    3. After installing the speed sensor, make sure there is no clearance or foreign matter between the sensor stay part and the knuckle.
    4. Make sure there is no foreign matter attached to the speed sensor rotor.


2. INSTALL FRONT SKID CONTROL SENSOR WIRE LH

  1. w/o AHC:

    1. C170883E01
      Connect the connector.

    2. Install the harness clamp with the bolt.

      Torque:
      13 N*m{ 127 kgf*cm , 9 ft.*lbf }

      NOTICE:
      1. When installing the clamp, do not twist the wire harness.
      2. Make sure the clamp rotation stopper touches the installation position.

  1. w/ AHC:

    1. C170884E01
      Connect the 2 connectors.

    2. Install the harness clamp with the bolt.

      Torque:
      13 N*m{ 127 kgf*cm , 9 ft.*lbf }

      NOTICE:
      1. When installing the clamp, do not twist the wire harness.
      2. Make sure the clamp rotation stopper touches the installation position.

  1. C170882
    Install the 2 harness clamps with the 2 bolts.

    Torque:
    13 N*m{ 127 kgf*cm , 9 ft.*lbf }

    NOTICE:
    1. When installing the clamps, do not twist the wire harness.
    2. Make sure the clamp rotation stopper touches the installation position.

  1. C177132
    Install the harness clamp with the nut.

    Torque:
    13 N*m{ 127 kgf*cm , 9 ft.*lbf }

    NOTICE:
    1. When installing the clamp, do not twist the wire harness.
    2. Make sure the clamp rotation stopper touches the installation position.

  1. C179349E01
    Install the harness clamp with bolt

    Torque:
    except China:
    13 N*m{ 127 kgf*cm , 9 ft.*lbf }
    for China:
    32 N*m{ 326 kgf*cm , 24 ft.*lbf }

    NOTICE:
    Install the bracket so that the rotation stopper touches the knuckle.

  1. Connect the speed sensor connector.

    NOTICE:
    Securely connect the connector.


3. INSTALL FRONT SPEED SENSOR RH

  1. C271343
    Install the speed sensor with the bolt.

    Torque:
    8.5 N*m{ 87 kgf*cm , 75 in.*lbf }

    NOTICE:
    1. Make sure there are no pieces of iron or other foreign matter attached to the sensor tip part.
    2. While inserting the speed sensor into the knuckle hole, do not strike or damage the sensor tip part.
    3. After installing the speed sensor, make sure there is no clearance or foreign matter between the sensor stay part and the knuckle.
    4. Make sure there is no foreign matter attached to the speed sensor rotor.


4. INSTALL FRONT SKID CONTROL SENSOR WIRE RH

  1. w/o AHC:

    1. C172203E01
      Install the skid control sensor clamp with the bolt (labeled A).

      Torque:
      for bolt A:
      13 N*m{ 127 kgf*cm , 9 ft.*lbf }

    2. Attach the connector to the skid control sensor clamp and then connect the connector.

    3. Install the 2 harness clamps with the 2 bolts.

      Torque:
      13 N*m{ 127 kgf*cm , 9 ft.*lbf }

      NOTICE:
      1. When installing the clamps, do not twist the wire harness.
      2. Make sure the clamp rotation stopper touches the installation position.

  1. w/ AHC:

    1. C170887E01
      Install the skid control sensor clamp with the bolt (labeled A).

      Torque:
      for bolt A:
      13 N*m{ 127 kgf*cm , 9 ft.*lbf }

    2. Attach the connector to the skid control sensor clamp and then connect the connector.

    3. Install the 2 harness clamps with the 2 bolts.

      Torque:
      13 N*m{ 127 kgf*cm , 9 ft.*lbf }

      NOTICE:
      1. When installing the clamps, do not twist the wire harness.
      2. Make sure the clamp rotation stopper touches the installation position.

    4. C170888
      Install the harness clamp with the bolt.

      Torque:
      13 N*m{ 127 kgf*cm , 9 ft.*lbf }

    5. Connect the connector.

  1. C177133
    Install the harness clamp with the nut.

    Torque:
    13 N*m{ 127 kgf*cm , 9 ft.*lbf }

    NOTICE:
    1. When installing the clamp, do not twist the wire harness.
    2. Make sure the clamp rotation stopper touches the installation position.

  1. C179350E01
    Install the harness clamp with bolt.

    Torque:
    except China:
    13 N*m{ 127 kgf*cm , 9 ft.*lbf }
    for China:
    32 N*m{ 326 kgf*cm , 24 ft.*lbf }

    NOTICE:
    Install the bracket so that the rotation stopper touches the knuckle.

  1. Connect the speed sensor connector.

    NOTICE:
    Securely connect the connector.


5. INSTALL FRONT WHEEL

Torque:
for Aluminum Wheel:
131 N*m{ 1336 kgf*cm , 97 ft.*lbf }
for Steel Wheel:
209 N*m{ 2131 kgf*cm , 154 ft.*lbf }


6. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


7. CHECK SPEED SENSOR SIGNAL
  1. w/ ABS:
    Check the speed sensor signal (Click here).

  1. w/ VSC:
    Check the speed sensor signal (Click here).

← INSTALLATION (Sep 2011 – Dec 2011)COMPONENTS (from Sep 2011) →