2011-2013 Land Cruiser · Service Manual Drivetrain

INSTALLATION

Removal / installation · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012


1. INSTALL OIL COOLER ASSEMBLY

C171508E02
  1. Connect the oil cooler inlet hose and outlet hose.

    Text in Illustration 
    *a
    Lower Side
    *b
    Outward

  1. Install the rear transmission oil cooler air duct with the 4 bolts, and then install the air cooled oil cooler tube to the transmission oil cooler air duct with the bolt.

    Torque:
    4.9 N*m{ 50 kgf*cm , 43 in.*lbf }

  1. C167869E02
    Temporarily put the oil cooler on the radiator support.
    Text in Illustration 
    *1
    Claw

    NOTICE:
    Securely attach the 2 claws of the oil cooler into the holes of the radiator support.

  1. Install the 4 bolts in the sequence shown in the illustration.

    Torque:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }


2. INSTALL TRANSMISSION OIL COOLER AIR DUCT
  1. Install the oil cooler air duct with the 4 bolts.

    Torque:
    4.9 N*m{ 50 kgf*cm , 43 in.*lbf }


3. INSTALL OIL COOLER TUBE

C226979E02
Text in Illustration 
*A
for 1VD-FTV
*B
for 3UR-FE
  1. Temporarily install the oil cooler tube to the fan shroud with bolt A. Install bolt B and tighten it to the specified torque. Then tighten bolt A to the specified torque.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }


4. CONNECT INLET NO. 4 OIL COOLER HOSE

C175576E02
  1. Connect the inlet oil cooler hose as shown in the illustration.

    NOTICE:
    Make sure the pinching portion of each clip is facing the direction shown in the illustration and the paint marks are aligned as shown in the illustration.

    Text in Illustration 
    *1
    Paint Mark


5. CONNECT INLET NO. 2 OIL COOLER HOSE AND INLET NO. 3 OIL COOLER HOSE

C226980E01
Text in Illustration 
*A
for 1VD-FTV
*B
for 3UR-FE
  1. Connect the 2 inlet oil cooler hoses as shown in the illustration.

    NOTICE:
    Make sure the pinching portion of each clip is facing the direction shown in the illustration.


6. CONNECT INLET NO. 1 OIL COOLER HOSE AND OUTLET NO. 1 OIL COOLER HOSE

C226981E01
Text in Illustration 
*A
for 1VD-FTV
*B
for 3UR-FE
*1
Paint Mark
-
-
  1. Connect the 2 oil cooler hoses as shown in the illustration.

    NOTICE:
    Make sure the pinching portion of each clip is facing the direction shown in the illustration and the paint marks are aligned as shown in the illustration.

  1. Attach the hose to the flexible hose clamp and close the clamp as shown in the illustration.


7. CONNECT TRANSMISSION OIL COOLER HOSE

C167860E02
  1. Connect the 2 transmission oil cooler hoses as shown in the illustration.

    NOTICE:
    1. Make sure the pinching portion of each clip is facing the direction shown in the illustration.
    2. Make sure the paint mark of each hose is facing outward.

    Text in Illustration 
    *1
    Paint Mark
    *a
    RH Side


8. ADD AUTOMATIC TRANSMISSION FLUID
  1. Add automatic transmission fluid (Click here).


9. INSTALL HEADLIGHT ASSEMBLY RH
for Standard: (Click here)
for HID headlight: (Click here)

HINT:
Use the same procedures described for LH side.


10. INSTALL NO. 2 ENGINE UNDER COVER

  1. A178462
    Install the engine under cover with the 2 bolts.

    Torque:
    29 N*m{ 296 kgf*cm , 21 ft.*lbf }


11. INSTALL NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY

  1. A178461
    Install the engine under cover with the 10 bolts.

    Torque:
    29 N*m{ 296 kgf*cm , 21 ft.*lbf }


12. REMOVE FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY LH

B180991
  1. Push in the clip indicated by the arrow in the illustration to install the fender splash shield.

  1. Install the 3 bolts and screw.


13. REMOVE FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY RH

HINT:
Use the same procedures described for the LH side.


14. INSTALL FRONT FENDER APRON SEAL REAR RH
  1. Install the fender apron seal with the 4 clips.


15. INSTALL FRONT FENDER APRON SEAL FRONT RH
  1. Install the fender apron seal with the 3 clips.

← REMOVAL (from Jan 2012)INSTALLATION (from Jan 2012) →