ON-VEHICLE INSPECTION
Inspection · Vehicles built Sep 2011 – Dec 2011
Versions by build date: Sep 2011 – Dec 2011 from Jan 2012
| OPERATE HEIGHT CONTROL SWITCH AND CHECK CHANGE OF VEHICLE HEIGHT |
- NOTICE:
- Perform the inspection with the vehicle empty.
- When operating the height control switch, operate the switch with the driver door opened, and then close the driver door after getting out of the vehicle.
- Perform the inspection with the vehicle empty.
- HINT:
- Vehicle height control starts just after closing the door.
Set the tires to the specified tire pressure, and adjust all 4 wheels.
For the front side, measure the ground clearance of the front adjusting cam bolt center.
For the rear side, measure the ground clearance of the rear lower control arm front side center.- HINT:
- Refer to the following for the measurements (Click here).
Start the engine.
Push the height control switch to change from "N" to "HI" mode.

Check the time required for the height change and the changed amount of the vehicle height.
- Standard Value:
Vehicle Condition
Fluid Temperature Condition
Reference Value
"HI" mode (Up time)
20°C (68°F) +/-10°C (50°F)
Approximately 15 seconds or less
- Amount of Change in Vehicle Height:
Item
Specified Condition
Front
Approximately +50 mm (+1.97 in.)
Rear
Approximately +60 mm (+2.36 in.)
- NOTICE:
- After vehicle height control has been completed, wait for approximately 20 seconds until the height is fixed securely, then check the changed amount of vehicle height.
Push the height control switch to change from "N" to "LO" mode.

Check the time required for the height change and the changed amount of the vehicle height.
- Standard Value:
Vehicle Condition
Fluid Temperature Condition
Reference Value
"LO" mode (Down time)
20°C (68°F) +/-10°C (50°F)
Approximately 10 seconds or less
- Amount of Change in Vehicle Height:
Item
Specified Condition
Front
Approximately -60 mm (-2.36 in.)
Rear
Approximately -40 mm (-1.57 in.)
- NOTICE:
- After vehicle height control has been completed, wait for approximately 20 seconds until the height is fixed securely, then check the changed amount of vehicle height.
| INSPECT FLUID PRESSURE |
- NOTICE:
- With the vehicle empty, perform this inspection with 1 person sitting in the driver seat in order to confirm that the switch operation and vehicle height change have been completed.
- HINT:
- The average weight for one person is about 55 kg (121.3 lb).
Turn the engine switch off.
Connect the intelligent tester to the DLC3.
Start the engine and turn the tester on.
Press the UP button of the height control switch. Using the Data List, check the oil pressure when the vehicle height changes from NORMAL to HI.
AHC Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Oil Pressure Sensor
Fluid pressure sensor reading /
min.: -784.79 MPa (-8002.66 kgf/cm2, -113794.55 psi)
max.: 784.76 MPa (8002.354 kgf/cm2, 113790.2 psi)
-
-
- Standard Pressure:
Vehicle Condition
Fluid Temperature Condition
Reference Value
When vehicle height changes from NORMAL to HI
20°C (68°F) +/-10°C (50°F)
The oil pressure begins rising when control is started and reaches approximately 13 MPa (132.6 kfg/cm2, 1885 psi) when the vehicle height is almost finished changing to HI.
Set the vehicle height to LO and press the UP button of the height control switch. Then check the oil pressure when the vehicle height changes from LO to NORMAL.
- Standard Pressure:
Vehicle Condition
Fluid Temperature Condition
Reference Value
When vehicle height changes from LO to NORMAL
20°C (68°F) +/-10°C (50°F)
The oil pressure begins rising when control is started and reaches approximately 8 MPa (81.6 kfg/cm2, 1160 psi) when the vehicle height is almost finished changing to NORMAL.
| INSPECT VEHICLE SPEED SENSING FUNCTION |
- HINT:
- When the vehicle speed sensing function control operates, nothing displays on the indicator in the combination meter.
Turn the engine switch off.
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG) and the tester on.
Using the Data List, check the vehicle speed sensing function.
AHC Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Height Mode
Height mode /
NORMAL / ACCE LO / LO / STAN LO / FAST LO / L4 HI / HI / EX HI
Actual conditions are displayed.
-
When the transfer is in the L4 position:
When the vehicle is driven at a speed of approximately 3 km/h (2 mph) or more, check that the vehicle height changes to HI using the Data List.
- OK:
- The display changes to HI.
Using the Data List, check if the vehicle height changes from HI to L4 HI when the vehicle speed is 40 km/h (25 mph) or more.
- OK:
- The display changes to L4 HI.
When driving at a high speed:
Using the Data List, check that the vehicle height lowers when the vehicle height is NORMAL and the vehicle speed is 100 km/h (62 mph) or more.
- OK:
- The display changes to FAST LO.
Using the Data List, check that the vehicle height returns to NORMAL when the vehicle speed is reduced to less than 80 km/h (50 mph).
- OK:
- The display changes to NORMAL.
When vehicle height control is prohibited:
Press the height control OFF switch to prohibit vehicle height control.
Drive the vehicle at 80 km/h (50 mph) or more with the vehicle height NORMAL, or drive the vehicle at 30 km/h (19 mph) or more with the vehicle height not NORMAL and, using the Data List, check that vehicle height control prohibition is canceled.
AHC Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Height Control Prohibition
Vehicle height control prohibition information/
Permiss or Prohibi
Actual conditions are displayed.
-
- OK:
- The display changes from Prohibi to Permiss.
