2011-2013 Land Cruiser · Service Manual Suspension

ON-VEHICLE INSPECTION

Inspection · Vehicles built from Jan 2012

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012


OPERATE HEIGHT CONTROL SWITCH AND CHECK CHANGE OF VEHICLE HEIGHT

NOTICE:
  1. Perform the inspection with the vehicle empty.
  2. When operating the height control switch, operate the switch with the driver door opened, and then close the driver door after getting out of the vehicle.

HINT:
Vehicle height control starts just after closing the door.

  1. Set the tires to the specified tire pressure, and adjust all 4 wheels.

  1. For the front side, measure the ground clearance of the front adjusting cam bolt center.
    For the rear side, measure the ground clearance of the rear lower control arm front side center.

    HINT:
    Refer to the following for the measurements (Click here).

  1. Start the engine.

  1. C175846
    Push the height control switch to change from "N" to "HI" mode.

  1. Check the time required for the height change and the changed amount of the vehicle height.

    Standard Value:
    Vehicle Condition
    Fluid Temperature Condition
    Reference Value
    "HI" mode (Up time)
    20°C (68°F) +/-10°C (50°F)
    Approximately 15 seconds or less

    Amount of Change in Vehicle Height:
    Item
    Specified Condition
    Front
    Approximately +50 mm (+1.97 in.)
    Rear
    Approximately +60 mm (+2.36 in.)

    NOTICE:
    After vehicle height control has been completed, wait for approximately 20 seconds until the height is fixed securely, then check the changed amount of vehicle height.

  1. C175847
    Push the height control switch to change from "N" to "LO" mode.

  1. Check the time required for the height change and the changed amount of the vehicle height.

    Standard Value:
    Vehicle Condition
    Fluid Temperature Condition
    Reference Value
    "LO" mode (Down time)
    20°C (68°F) +/-10°C (50°F)
    Approximately 10 seconds or less

    Amount of Change in Vehicle Height:
    Item
    Specified Condition
    Front
    Approximately -60 mm (-2.36 in.)
    Rear
    Approximately -40 mm (-1.57 in.)

    NOTICE:
    After vehicle height control has been completed, wait for approximately 20 seconds until the height is fixed securely, then check the changed amount of vehicle height.


INSPECT FLUID PRESSURE

NOTICE:
With the vehicle empty, perform this inspection with 1 person sitting in the driver seat in order to confirm that the switch operation and vehicle height change have been completed.

HINT:
The average weight for one person is about 55 kg (121.3 lb).

  1. Turn the engine switch off.

  1. Connect the intelligent tester to the DLC3.

  1. Start the engine and turn the tester on.

  1. Press the UP button of the height control switch. Using the Data List, check the oil pressure when the vehicle height changes from NORMAL to HI.

    AHC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Oil Pressure Sensor
    Fluid pressure sensor reading /
    min.: -784.79 MPa (-8002.66 kgf/cm2, -113794.55 psi)
    max.: 784.76 MPa (8002.354 kgf/cm2, 113790.2 psi)
    -
    -

    Standard Pressure:
    Vehicle Condition
    Fluid Temperature Condition
    Reference Value
    When vehicle height changes from NORMAL to HI
    20°C (68°F) +/-10°C (50°F)
    The oil pressure begins rising when control is started and reaches approximately 13 MPa (132.6 kfg/cm2, 1885 psi) when the vehicle height is almost finished changing to HI.

  1. Set the vehicle height to LO and press the UP button of the height control switch. Then check the oil pressure when the vehicle height changes from LO to NORMAL.

    Standard Pressure:
    Vehicle Condition
    Fluid Temperature Condition
    Reference Value
    When vehicle height changes from LO to NORMAL
    20°C (68°F) +/-10°C (50°F)
    The oil pressure begins rising when control is started and reaches approximately 8 MPa (81.6 kfg/cm2, 1160 psi) when the vehicle height is almost finished changing to NORMAL.


INSPECT VEHICLE SPEED SENSING FUNCTION

HINT:
When the vehicle speed sensing function control operates, nothing displays on the indicator in the combination meter.

  1. Turn the engine switch off.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the engine switch on (IG) and the tester on.

  1. Using the Data List, check the vehicle speed sensing function.

    AHC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Height Mode
    Height mode /
    NORMAL / ACCE LO / LO / STAN LO / FAST LO / L4 HI / HI / EX HI
    Actual conditions are displayed.
    -

  1. When the transfer is in the L4 position:

    1. When the vehicle is driven at a speed of approximately 3 km/h (2 mph) or more, check that the vehicle height changes to HI using the Data List.

      OK:
      The display changes to HI.

    2. Using the Data List, check if the vehicle height changes from HI to L4 HI when the vehicle speed is 40 km/h (25 mph) or more.

      OK:
      The display changes to L4 HI.

  1. When driving at a high speed:

    1. Using the Data List, check that the vehicle height lowers when the vehicle height is NORMAL and the vehicle speed is 100 km/h (62 mph) or more.

      OK:
      The display changes to FAST LO.

    2. Using the Data List, check that the vehicle height returns to NORMAL when the vehicle speed is reduced to less than 80 km/h (50 mph).

      OK:
      The display changes to NORMAL.

  1. When vehicle height control is prohibited:

    1. Press the height control OFF switch to prohibit vehicle height control.

    2. Drive the vehicle at 80 km/h (50 mph) or more with the vehicle height NORMAL, or drive the vehicle at 30 km/h (19 mph) or more with the vehicle height not NORMAL and, using the Data List, check that vehicle height control prohibition is canceled.

      AHC 
      Tester Display
      Measurement Item/Range
      Normal Condition
      Diagnostic Note
      Height Control Prohibition
      Vehicle height control prohibition information/
      Permiss or Prohibi
      Actual conditions are displayed.
      -

      OK:
      The display changes from Prohibi to Permiss.

← ON-VEHICLE INSPECTION (Sep 2011 – Dec 2011)C1711 Front Height Control Sensor RH Circuit Malfunction (+ C1712, C1713, C1714) (Sep 2011 – Dec 2011) →