2011-2013 Land Cruiser · Service Manual Brake

TERMINALS OF ECU

System information · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012


TERMINALS OF ECU
C140176E05
Terminal No. (Symbol)
Terminal Description
A24-1 (GND1)
Skid control ECU ground
A24-2 (+BM1)
Power supply for motor
A24-3 (FR+)
Front speed sensor RH power supply output
A24-4 (FL-)
Front speed sensor LH input
A24-5 (RR+)
Rear speed sensor RH power supply output
A24-6 (RL-)
Rear speed sensor LH input
A24-7 (STP)
Stop light switch
A24-9 (TRS)
CRAWL ON/OFF switch
A24-11 (CANH)
CAN communication terminal H
A24-12 (SP1)
Speedometer signal
A24-13 (D/G)
Diagnosis tester serial communication
A24-16 (STP0)
Stop light operation relay
A24-17 (FR-)
Front speed sensor RH input
A24-18 (FL+)
Front speed sensor LH power supply output
A24-19 (RR-)
Rear speed sensor RH input
A24-20 (RL+)
Rear speed sensor LH power supply output
A24-21 (TRM2)
CRAWL speed selector switch
A24-24 (TS)
Sensor test terminal (Signal check switch)
A24-25 (CANL)
CAN communication terminal L
A24-27 (EXI)
Center differential lock switch
A24-28 (PKB)
Parking brake input
A24-30 (BZ)
Skid control buzzer
A24-31 (+BS)
Power supply for solenoid
A24-32 (GND2)
Skid control ECU ground
A24-41 (LBL)
Brake fluid level warning switch
A24-42 (WFSE)
Write flash enable input
A24-43 (CSW)
VSC OFF switch
A24-44 (TRM1)
CRAWL speed selector switch
A24-45 (STP2)
Stop light switch
A24-46 (IG1)
IG1 power supply
C172937E01
Terminal No. (Symbol)
Terminal Description
A25-1 (IG2)
IG2 power supply
A25-2 (+BM2)
Power supply for motor
A25-4 (GND3)
Skid control ECU ground

TERMINAL INSPECTION
Disconnect the connector and measure the voltage or resistance on the wire harness side.

HINT:
Voltage cannot be measured with the connector connected to the skid control ECU as the connector is watertight.

C173112E01
Terminal No. (Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
A24-2 (+BM1) - Body ground
B
Power supply for motor
(From battery)
Always
11 to 14 V
A24-16 (STP0) - Body ground
R-Y
Stop light operation relay
Ignition switch off → ON
Below 1 V → 11 to 14 V
A24-28 (PKB) - Body ground
Y-R
Parking brake input
Parking brake switch on → off (Parking brake lever pulled → released)
Below 1 Ω → 10 kΩ or higher
A24-31 (+BS) - Body ground
W
Power supply for solenoid
(From battery)
Always
11 to 14 V
A24-41 (LBL) - Body ground
BR-Y
Brake fluid level warning switch
Brake fluid level +/-5 mm (+/-0.197 in.) from the minimum level → maximum level
Below 1 Ω → 1.9 to 2.1 kΩ
A24-43 (CSW) - Body ground
G-W
VSC OFF switch input
VSC OFF switch off → on
10 kΩ or higher → Below 1 Ω
A24-45 (STP2) - Body ground
R
Stop light switch
Stop light switch on → off
(Brake pedal depressed → released)
8 to 14 V → Below 1.5 V
A24-46 (IG1) - Body ground
G
IG1 power supply
Ignition switch off → ON
Below 1 V → 11 to 14 V
A25-1 (IG2) - Body ground
B
IG2 power supply
Ignition switch off → ON
Below 1 V → 11 to 14 V
A25-2 (+BM2) - Body ground
B
Power supply for motor
(From battery)
Always
11 to 14 V
A24-1 (GND1) - Body ground
W-B
Ground
Always
Below 1 Ω
A24-32 (GND2) - Body ground
W-B
Ground
Always
Below 1 Ω
A25-4 (GND3) - Body ground
W-B
Ground
Always
Below 1 Ω
← PROBLEM SYMPTOMS TABLE (from Jan 2012)TERMINALS OF ECU (from Jan 2012) →