2011-2013 Land Cruiser · Service Manual Brake

TERMINALS OF ECU

System information · Vehicles built from Jan 2012

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012


TERMINALS OF ECU
C140176E10
Text in Illustration 
*a
Component without harness connected
(Skid Control ECU [Master Cylinder Solenoid])
-
-
Terminal No. (Symbol)
Terminal Description
1 (GND1)
Skid control ECU (Master cylinder solenoid) ground
2 (+BM1)
Power supply for motor
3 (FR+)
Front speed sensor RH power supply output
4 (FL-)
Front speed sensor LH input
5 (RR+)
Rear speed sensor RH power supply output
6 (RL-)
Rear speed sensor LH input
7 (STP)
Stop light switch
9 (CSW)
VSC OFF switch
11 (CANH)
CAN communication terminal H
12 (SP1)
Speedometer signal
13 (ATRC)
CRAWL speed selector switch
16 (STPO)
BRK LP relay (Brake light relay)
17 (FR-)
Front speed sensor RH input
18 (FL+)
Front speed sensor LH power supply output
19 (RR-)
Rear speed sensor RH input
20 (RL+)
Rear speed sensor LH power supply output
21 (TRM2)
CRAWL speed selector switch
24 (TS)
Sensor test terminal (Signal check switch)
25 (CANL)
CAN communication terminal L
27 (EXI)
Center differential lock switch
29 (EXI4)
Turn assist function switch signal
30 (BZ)*
Skid control buzzer
31 (+BS)
Power supply for solenoid
32 (GND2)
Skid control ECU (Master cylinder solenoid) ground
41 (LBL)
Brake fluid level warning switch
43 (TRS)
CRAWL ON/OFF switch
44 (TRM1)
CRAWL speed selector switch
45 (STP2)
BRK LP relay (Brake light relay)
46 (IG1)
IG1 power supply
  1. *: w/ Dynamic Radar Cruise Control System
C172937E05
Text in Illustration 
*a
Component without harness connected
(Skid Control ECU [Master Cylinder Solenoid])
-
-
Terminal No. (Symbol)
Terminal Description
1 (IG2)
IG2 power supply
2 (+BM2)
Power supply for motor
4 (GND3)
Skid control ECU (Master cylinder solenoid) ground

TERMINAL INSPECTION
Disconnect the connector and measure the voltage or resistance on the wire harness side.

HINT:
Voltage cannot be measured with the connector connected to the skid control ECU (master cylinder solenoid) as the connector is watertight.

C173112E06
Text in Illustration 
*a
Front view of wire harness connector
(to Skid Control ECU [Master Cylinder Solenoid])
-
-
Terminal No. (Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
A24-2 (+BM1) - Body ground
B
Power supply for motor
(From battery)
Always
11 to 14 V
A24-7 (STP) - Body ground
R
Stop light switch
Brake pedal depressed → released
8 to 14 V → Below 1.5 V
A24-9 (CSW) - Body ground
G-W
VSC OFF switch input
VSC OFF switch off → on
10 kΩ or higher → Below 1 Ω
A24-16 (STPO) - Body ground
R-Y
BRK LP relay (Brake light relay)
Ignition switch off → ON
Below 1 V → 11 to 14 V
A24-31 (+BS) - Body ground
W
Power supply for solenoid
(From battery)
Always
11 to 14 V
A24-41 (LBL) - Body ground
BR-Y
Brake fluid level warning switch (Brake master cylinder reservoir sub-assembly)
Brake fluid level +/-5 mm (+/-0.197 in.) from the minimum level → maximum level
Below 1 Ω → 1.9 to 2.1 kΩ
A24-45 (STP2) - Body ground
R
BRK LP relay (Brake light relay)
Brake pedal depressed → released
8 to 14 V → Below 1.5 V
A24-46 (IG1) - Body ground
G
IG1 power supply
Ignition switch off → ON
Below 1 V → 11 to 14 V
A25-1 (IG2) - Body ground
B
IG2 power supply
Ignition switch off → ON
Below 1 V → 11 to 14 V
A25-2 (+BM2) - Body ground
B
Power supply for motor
(From battery)
Always
11 to 14 V
A24-1 (GND1) - Body ground
W-B
Ground
Always
Below 1 Ω
A24-32 (GND2) - Body ground
W-B
Ground
Always
Below 1 Ω
A25-4 (GND3) - Body ground
W-B
Ground
Always
Below 1 Ω
← TERMINALS OF ECU (Sep 2011 – Dec 2011)DIAGNOSIS SYSTEM (Sep 2011 – Dec 2011) →