TERMINALS OF ECU
System information · Vehicles built Sep 2011 – Dec 2011
Versions by build date: Sep 2011 – Dec 2011 from Jan 2012
| TERMINALS OF ECU |


| Terminal No. (Symbol) |
Terminal Description |
| A24-1 (GND1) |
Skid control ECU ground |
| A24-2 (+BM1) |
Power supply for motor |
| A24-3 (FR+) |
Front speed sensor RH power supply output |
| A24-4 (FL-) |
Front speed sensor LH input |
| A24-5 (RR+) |
Rear speed sensor RH power supply output |
| A24-6 (RL-) |
Rear speed sensor LH input |
| A24-7 (STP) |
Stop light switch |
| A24-11 (CANH) |
CAN communication terminal H |
| A24-12 (SP1) |
Speedometer signal |
| A24-13 (D/G) |
Diagnosis tester serial communication |
| A24-17 (FR-) |
Front speed sensor RH input |
| A24-18 (FL+) |
Front speed sensor LH power supply output |
| A24-19 (RR-) |
Rear speed sensor RH input |
| A24-20 (RL+) |
Rear speed sensor LH power supply output |
| A24-22 (VGS) |
G sensor power supply output |
| A24-23 (GGND) |
G sensor ground |
| A24-24 (TS) |
Sensor test terminal (Signal check switch) |
| A24-25 (CANL) |
CAN communication terminal L |
| A24-26 (EXI3) |
Rear differential lock detection switch |
| A24-27 (EXI) |
Center differential lock switch |
| A24-28 (PKB) |
Parking brake input |
| A24-30 (BZ) |
Skid control buzzer |
| A24-31 (+BS) |
Power supply for solenoid |
| A24-32 (GND2) |
Skid control ECU ground |
| A24-39 (GL1) |
G sensor input |
| A24-41 (LBL) |
Brake fluid level warning switch |
| A24-42 (WFSE) |
Write flash enable input |
| A24-46 (IG1) |
IG1 power supply |


| Terminal No. (Symbol) |
Terminal Description |
| A25-1 (IG2) |
IG2 power supply |
| A25-2 (+BM2) |
Power supply for motor |
| A25-4 (GND3) |
Skid control ECU ground |
| TERMINAL INSPECTION |
- HINT:
- Voltage cannot be measured with the connector connected to the skid control ECU as the connector is watertight.


| Terminal No. (Symbol) |
Wiring Color |
Terminal Description |
Condition |
Specified Condition |
| A24-2 (+BM1) - Body ground |
B |
Power supply for motor (From battery) |
Always |
11 to 14 V |
| A24-28 (PKB) - Body ground |
Y-R |
Parking brake input |
Parking brake switch on → off (Parking brake lever pulled → released) |
Below 1 Ω → 10 kΩ or higher |
| A24-31 (+BS) - Body ground |
W |
Power supply for solenoid (From battery) |
Always |
11 to 14 V |
| A24-41 (LBL) - Body ground |
BR-Y |
Brake fluid level warning switch |
Brake fluid level +/- 5 mm (+/- 0.197 in.) from the minimum level → maximum level |
Below 1 Ω → 1.9 to 2.1 kΩ |
| A24-46 (IG1) - Body ground |
G |
IG1 power supply |
Ignition switch off → ON |
Below 1 V → 11 to 14 V |
| A25-1 (IG2) - Body ground |
B |
IG2 power supply |
Ignition switch off → ON |
Below 1 V → 11 to 14 V |
| A25-2 (+BM2) - Body ground |
B |
Power supply for motor (From battery) |
Always |
11 to 14 V |
| A24-1 (GND1) - Body ground |
W-B |
Ground |
Always |
Below 1 Ω |
| A24-32 (GND2) - Body ground |
W-B |
Ground |
Always |
Below 1 Ω |
| A25-4 (GND3) - Body ground |
W-B |
Ground |
Always |
Below 1 Ω |