TERMINALS OF ECU
System information · Vehicles built from Jan 2012
Versions by build date: Sep 2011 – Dec 2011 from Jan 2012
| TERMINALS OF ECU |


| *a |
Component without harness connected (Skid Control ECU [Master Cylinder Solenoid]) |
- |
- |
| Terminal No. (Symbol) |
Terminal Description |
| 1 (GND1) |
Skid control ECU (Master cylinder solenoid) ground |
| 2 (+BM1) |
Power supply for motor |
| 3 (FR+) |
Front speed sensor RH power supply output |
| 4 (FL-) |
Front speed sensor LH input |
| 5 (RR+) |
Rear speed sensor RH power supply output |
| 6 (RL-) |
Rear speed sensor LH input |
| 7 (STP) |
Stop light switch |
| 11 (CANH) |
CAN communication terminal H |
| 12 (SP1) |
Speedometer signal |
| 14 (P) |
Rear differential lock detection switch |
| 17 (FR-) |
Front speed sensor RH input |
| 18 (FL+) |
Front speed sensor LH power supply output |
| 19 (RR-) |
Rear speed sensor RH input |
| 20 (RL+) |
Rear speed sensor LH power supply output |
| 22 (VGS) |
Deceleration sensor power supply output |
| 23 (GGND) |
Deceleration sensor ground |
| 24 (TS) |
Sensor test terminal (Signal check switch) |
| 25 (CANL) |
CAN communication terminal L |
| 27 (EXI) |
Center differential lock switch |
| 31 (+BS) |
Power supply for solenoid |
| 32 (GND2) |
Skid control ECU (Master cylinder solenoid) ground |
| 39 (GL1) |
Deceleration sensor input |
| 41 (LBL) |
Brake fluid level warning switch |
| 46 (IG1) |
IG1 power supply |


| *a |
Component without harness connected (Skid Control ECU [Master Cylinder Solenoid]) |
- |
- |
| Terminal No. (Symbol) |
Terminal Description |
| 1 (IG2) |
IG2 power supply |
| 2 (+BM2) |
Power supply for motor |
| 4 (GND3) |
Skid control ECU (Master cylinder solenoid) ground |
| TERMINAL INSPECTION |
- HINT:
- Voltage cannot be measured with the connector connected to the skid control ECU (master cylinder solenoid) as the connector is watertight.


| *a |
Front view of wire harness connector (to Skid Control ECU [Master Cylinder Solenoid]) |
- |
- |
| Terminal No. (Symbol) |
Wiring Color |
Terminal Description |
Condition |
Specified Condition |
| A24-2 (+BM1) - Body ground |
B |
Power supply for motor (From battery) |
Always |
11 to 14 V |
| A24-7 (STP) - Body ground |
R |
Stop light switch |
Brake pedal depressed → released |
8 to 14 V → Below 1.5 V |
| A24-31 (+BS) - Body ground |
W |
Power supply for solenoid (From battery) |
Always |
11 to 14 V |
| A24-41 (LBL) - Body ground |
BR-Y |
Brake fluid level warning switch (Brake master cylinder reservoir sub-assembly) |
Brake fluid level +/-5 mm (+/-0.197 in.) from the minimum level → maximum level |
Below 1 Ω → 1.9 to 2.1 kΩ |
| A24-46 (IG1) - Body ground |
G |
IG1 power supply |
Ignition switch off → ON |
Below 1 V → 11 to 14 V |
| A25-1 (IG2) - Body ground |
B |
IG2 power supply |
Ignition switch off → ON |
Below 1 V → 11 to 14 V |
| A25-2 (+BM2) - Body ground |
B |
Power supply for motor (From battery) |
Always |
11 to 14 V |
| A24-1 (GND1) - Body ground |
W-B |
Ground |
Always |
Below 1 Ω |
| A24-32 (GND2) - Body ground |
W-B |
Ground |
Always |
Below 1 Ω |
| A25-4 (GND3) - Body ground |
W-B |
Ground |
Always |
Below 1 Ω |