2011-2013 Land Cruiser · Service Manual Brake

DATA LIST / ACTIVE TEST

System information · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012


DATA LIST

HINT:
Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Connect the intelligent tester to the DLC3.

  2. Turn the ignition switch to ON.

  3. Turn the intelligent tester on.

  4. Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

  5. According to the display on the intelligent tester, read the Data List.

    ABS/VSC/TRC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    ABS Warning Light
    ABS warning light / ON or OFF
    ON: Warning light on
    OFF: Warning light off
    -
    Brake Warning Light
    Brake warning light / red (malfunction) / ON or OFF
    ON: Warning light on
    OFF: Warning light off
    -
    Buzzer
    Skid control buzzer / ON or OFF
    ON: Buzzer on
    OFF: Buzzer off
    -
    Stop Light SW
    Stop light switch / ON or OFF
    ON: Brake pedal depressed
    OFF: Brake pedal released
    -
    Parking Brake SW
    Parking brake switch / ON or OFF
    ON: Parking brake applied
    OFF: Parking brake released
    -
    Reservoir Warning SW
    Brake fluid level warning switch / ON or OFF
    ON: Reservoir level normal
    OFF: Reservoir level low
    -
    Main Idle SW
    Main idle switch / ON or OFF
    ON: Accelerator pedal released
    OFF: Accelerator pedal depressed
    -
    Gear Position
    Gear position / Fail, 1st, 2nd, 3rd, 4th, 5th, 6th, P,N, R, Not R
    Actual gear position
    -
    Shift Lever Position
    Shift lever position / Fail, 1st, 2nd, 3rd, 4th, 5th, 6th/B, D/M, P,N, R
    Actual shift lever position
    -
    Shift Information
    Shift information / OFF or ON
    OFF: When not shifting
    ON: When shifting
    -
    Master Cylinder Sensor
    Master cylinder pressure sensor reading / min.: 0.00 V, max.: 5.00 V
    When brake pedal released: 0.3 to 0.9 V
    The reading increases when the brake pedal is depressed.
    Zero Point of M/C
    Memorized zero value / min.: -12.50 MPa, max.: 12.40 MPa
    -
    -
    Accumulator Sensor
    Accumulator pressure sensor reading / min.: 0.00 V, max.: 5.00 V
    3.58 to 5 V
    If the value is constant regardless of the pump operation, an accumulator pressure sensor malfunction is suspected.
    Deceleration Sensor
    Deceleration sensor reading / min.: -18.525 m/s2, max.: 18.387 m/s2
    Approximately -1.28 to 1.27 m/s2 while stationary
    The reading changes when the vehicle is bounced.
    Zero Point of Decele
    Memorized zero value / min.: -25.10 m/s2, max.: 24.90 m/s2
    Min.: -14.7 m/s2
    Max.: 14.7 m/s2
    -
    Forward and Rearward G
    Forward and rearward G / min.: -25.10 m/s2, max.: 24.90 m/s2
    Min.: -14.7 m/s2
    Max.: 14.7 m/s2
    -
    FR Wheel Speed
    Front wheel speed sensor RH reading / min.: 0 km/h (0 mph), max.: 326 km/h (202 mph)
    Actual wheel speed
    A similar speed is indicated on the speedometer.
    FL Wheel Speed
    Front wheel speed sensor LH reading / min.: 0 km/h (0 mph), max.: 326 km/h (202 mph)
    Actual wheel speed
    A similar speed is indicated on the speedometer.
    RR Wheel Speed
    Rear wheel speed sensor RH reading / min.: 0 km/h (0 mph), max.: 326 km/h (202 mph)
    Actual wheel speed
    A similar speed is indicated on the speedometer.
    RL Wheel Speed
    Rear wheel speed sensor LH reading / min.: 0 km/h (0 mph), max.: 326 km/h (202 mph)
    Actual wheel speed
    A similar speed is indicated on the speedometer.
    Vehicle Speed
    Maximum wheel speed sensor reading / min.: 0 km/h (0 mph), max.: 326 km/h (202 mph)
    Actual vehicle speed
    The speed is indicated on the speedometer.
    FR Wheel Acceleration
    Front wheel acceleration RH / min.: -200.84 m/s2, max.: 199.27 m/s2
    Min.: -200.84 m/s2
    Max.: 199.27 m/s2
    -
    FL Wheel Acceleration
    Front wheel acceleration LH / min.: -200.84 m/s2, max.: 199.27 m/s2
    Min.: -200.84 m/s2
    Max.: 199.27 m/s2
    -
    RR Wheel Acceleration
    Rear wheel acceleration RH / min.: -200.84 m/s2, max.: 199.27 m/s2
    Min.: -200.84 m/s2
    Max.: 199.27 m/s2
    -
    RL Wheel Acceleration
    Rear wheel acceleration LH / min.: -200.84 m/s2, max.: 199.27 m/s2
    Min.: -200.84 m/s2
    Max.: 199.27 m/s2
    -
    FR Wheel Direction
    Front wheel direction RH / Forward or Back
    Forward: Forward
    Back: Backward
    -
    FL Wheel Direction
    Front wheel direction LH / Forward or Back
    Forward: Forward
    Back: Backward
    -
    RR Wheel Direction
    Rear wheel direction RH / Forward or Back
    Forward: Forward
    Back: Backward
    -
    RL Wheel Direction
    Rear wheel direction LH / Forward or Back
    Forward: Forward
    Back: Backward
    -
    FR Wheel ABS Ctrl Status
    Front wheel RH ABS control status / ON or OFF
    ON: During control
    OFF: Not during control
    -
    FL Wheel ABS Ctrl Status
    Front wheel LH ABS control status / ON or OFF
    ON: During control
    OFF: Not during control
    -
    RR Wheel ABS Ctrl Status
    Rear wheel RH ABS control status / ON or OFF
    ON: During control
    OFF: Not during control
    -
    RL Wheel ABS Ctrl Status
    Rear wheel LH ABS control status / ON or OFF
    ON: During control
    OFF: Not during control
    -
    RR Wheel EBD Ctrl Status
    Rear wheel RH EBD control status / ON or OFF
    ON: During control
    OFF: Not during control
    -
    RL Wheel EBD Ctrl Status
    Rear wheel LH EBD control status / ON or OFF
    ON: During control
    OFF: Not during control
    -
    BA Ctrl Status
    BA control status / ON or OFF
    ON: During control
    OFF: Not during control
    -
    Engine Revolutions
    Engine speed / min.: 0 rpm, max.: 65535 rpm
    Actual engine speed
    -
    Real Engine Torque
    Real engine torque / min.: -1024.0 Nm, max.: 1023.0 Nm
    Actual engine torque
    -
    Accelerator Opening Angle %
    Percentage of accelerator pedal opening angle / min.: 0.0%, max.: 128.0%
    Min.: 0%
    Max.: 100%
    -
    Solenoid Relay
    Solenoid relay / ON or OFF
    ON: Solenoid relay on
    OFF: Solenoid relay off
    -
    Electronically Controlled Brake System Motor Relay
    Electronically controlled brake system motor relay / ON or OFF
    ON: Motor relay on
    OFF: Motor relay off
    -
    TR(A)C/VSC Solenoid (SRM2)
    TRC/VSC solenoid (SRM2) / ON or OFF
    ON: Operates
    OFF: Does not operate
    -
    TR(A)C/VSC Solenoid (SRM1)
    TRC/VSC solenoid (SRM1) / ON or OFF
    ON: Operates
    OFF: Does not operate
    -
    TR(A)C/VSC Solenoid (SRC2)
    TRC/VSC solenoid (SRC2) / ON or OFF
    ON: Operates
    OFF: Does not operate
    -
    TR(A)C/VSC Solenoid (SRC1)
    TRC/VSC solenoid (SRC1) / ON or OFF
    ON: Operates
    OFF: Does not operate
    -
    ABS Solenoid (SFRH)
    ABS solenoid (SFRH) / ON or OFF
    ON: Operates
    OFF: Does not operate
    -
    ABS Solenoid (SFRR)
    ABS solenoid (SFRR) / ON or OFF
    ON: Operates
    OFF: Does not operate
    -
    ABS Solenoid (SFLH)
    ABS solenoid (SFLH) / ON or OFF
    ON: Operates
    OFF: Does not operate
    -
    ABS Solenoid (SFLR)
    ABS solenoid (SFLR) / ON or OFF
    ON: Operates
    OFF: Does not operate
    -
    ABS Solenoid (SRRH)
    ABS solenoid (SRRH) / ON or OFF
    ON: Operates
    OFF: Does not operate
    -
    ABS Solenoid (SRRR)
    ABS solenoid (SRRR) / ON or OFF
    ON: Operates
    OFF: Does not operate
    -
    ABS Solenoid (SRLH)
    ABS solenoid (SRLH) / ON or OFF
    ON: Operates
    OFF: Does not operate
    -
    ABS Solenoid (SRLR)
    ABS solenoid (SRLR) / ON or OFF
    ON: Operates
    OFF: Does not operate
    -
    FR Speed Open
    Front speed sensor RH open detection / Error or Normal
    Error: Momentary interruption
    Normal: Normal
    -
    FL Speed Open
    Front speed sensor LH open detection / Error or Normal
    Error: Momentary interruption
    Normal: Normal
    -
    RR Speed Open
    Rear speed sensor RH open detection / Error or Normal
    Error: Momentary interruption
    Normal: Normal
    -
    RL Speed Open
    Rear speed sensor LH open detection / Error or Normal
    Error: Momentary interruption
    Normal: Normal
    -
    EFI Communication Open
    ECM communication open detection / Error or Normal
    Error: Momentary interruption
    Normal: Normal
    -
    IG1 Voltage Value
    IG1 voltage value / min.: 0.00 V, max.: 20.00V
    9.5 to 14 V
    -
    IG2 Voltage Value
    IG2 voltage value / min.: 0.00 V, max.: 20.00V
    9.5 to 14 V
    -
    Number of DTC
    Number of DTCs / min.: 0, max.: 255
    Min.: 0
    Max.: 255
    -


ACTIVE TEST

HINT:
Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

  1. Connect the intelligent tester to the DLC3.

  2. Turn the ignition switch to ON.

  3. Turn the intelligent tester on.

  4. Enter the following menus: Chassis / ABS/VSC/TRC / Active Test.

  5. According to the display on the intelligent tester, perform the Active Test.

ABS/VSC/TRC 
Tester Display
Test Part
Control Range
Diagnostic Note
ABS Warning Light
ABS warning light
Warning light ON/OFF
Observe the combination meter.
Brake Warning Light
BRAKE warning light
Warning light ON/OFF
Observe the combination meter.
Buzzer
Skid control buzzer
Buzzer ON/OFF
The buzzer can be heard.
Solenoid Relay
Solenoid relay
Relay ON/OFF
An operation sound of the solenoid (clicking sound) can be heard.
Motor Relay
Motor relay
Relay ON/OFF
An operation sound of the motor can be heard.
ABS Solenoid (SRLR)
ABS solenoid (SRLR)
Solenoid ON/OFF
An operation sound of the solenoid (clicking sound) can be heard.
ABS Solenoid (SRLH)
ABS solenoid (SRLH)
Solenoid ON/OFF
An operation sound of the solenoid (clicking sound) can be heard.
ABS Solenoid (SRRR)
ABS solenoid (SRRR)
Solenoid ON/OFF
An operation sound of the solenoid (clicking sound) can be heard.
ABS Solenoid (SRRH)
ABS solenoid (SRRH)
Solenoid ON/OFF
An operation sound of the solenoid (clicking sound) can be heard.
ABS Solenoid (SFLR)
ABS solenoid (SFLR)
Solenoid ON/OFF
An operation sound of the solenoid (clicking sound) can be heard.
ABS Solenoid (SFLH)
ABS solenoid (SFLH)
Solenoid ON/OFF
An operation sound of the solenoid (clicking sound) can be heard.
ABS Solenoid (SFRR)
ABS solenoid (SFRR)
Solenoid ON/OFF
An operation sound of the solenoid (clicking sound) can be heard.
ABS Solenoid (SFRH)
ABS solenoid (SFRH)
Solenoid ON/OFF
An operation sound of the solenoid (clicking sound) can be heard.
VSC/TRC Solenoid (SRMR)
VSC/TRC solenoid (SRMR (SMCR, STR))
Solenoid ON/OFF
An operation sound of the solenoid (clicking sound) can be heard.
VSC/TRC Solenoid (SRMF)
VSC/TRC solenoid (SRMF (SMCF, SA3))
Solenoid ON/OFF
An operation sound of the solenoid (clicking sound) can be heard.
VSC/TRC Solenoid (SRCR)
VSC/TRC solenoid (SRCR (SA2))
Solenoid ON/OFF
An operation sound of the solenoid (clicking sound) can be heard.
VSC/TRC Solenoid (SRCF)
VSC/TRC solenoid (SRCF (SA1))
Solenoid ON/OFF
An operation sound of the solenoid (clicking sound) can be heard.
← FAIL-SAFE CHART (from Jan 2012)DATA LIST / ACTIVE TEST (from Jan 2012) →