DATA LIST / ACTIVE TEST
System information · Vehicles built from Jan 2012
Versions by build date: Sep 2011 – Dec 2011 from Jan 2012
| DATA LIST |
- HINT:
- Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
- NOTICE:
- In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Warm up the engine.
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Chassis / ABS/VSC/TRC / Data List.
According to the display on the GTS, read the Data List.
ABS/VSC/TRC Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
ABS Warning Light
ABS warning light/ ON or OFF
ON: Warning light on
OFF: Warning light off
-
Brake Warning Light
Brake warning light/ ON or OFF
ON: Warning light on
OFF: Warning light off
-
Buzzer
Buzzer/ ON or OFF
ON: Buzzer on
OFF: Buzzer off
The combination meter has a built-in buzzer.
Stop Light SW
Stop light switch/ ON or OFF
ON: Brake pedal depressed
OFF: Brake pedal released
-
Parking Brake SW
Parking brake switch/ ON or OFF
ON: Parking brake applied
OFF: Parking brake released
-
Reservoir Warning SW
Brake fluid level warning switch/ ON or OFF
OFF
-
Main Idle SW
Main idle switch/ ON or OFF
ON: Accelerator pedal released
OFF: Accelerator pedal depressed
-
Master Cylinder Sensor
Master cylinder pressure sensor reading/ Min.: 0.00 V, Max.: 5.00 V
When brake pedal released: 0.3 to 0.9 V
The value increases when the brake pedal is depressed.
Zero Point of M/C
Memorized zero value/ Min.: -12.50 MPa, Max.: 12.40 MPa
-
-
Accumulator Sensor
Accumulator pressure sensor reading/ Min.: 0.00 V, Max.: 5.00 V
3.58 to 5 V
If the value is constant regardless of the pump operation, an accumulator pressure sensor malfunction is suspected.
Deceleration Sensor
Deceleration sensor reading/ Min.: -18.525 m/s2, Max.: 18.387 m/s2
-
Changes continuously during acceleration/deceleration.
Zero Point of Decele
Memorized zero value/ Min.: -25.10 m/s2, Max.: 24.90 m/s2
-
-
Forward and Rearward G
Forward and rearward G/ Min.: -25.10 m/s2, Max.: 24.90 m/s2
-
Changes in proportion with acceleration during acceleration/deceleration.
Rear Diff Lock Switch
Rear differential lock detection switch/ ON or OFF
ON: Rear differential lock detection switch on
OFF: Rear differential lock detection switch off
-
L4 Switch
Transfer L4 detection switch/ ON or OFF
ON: L4
OFF: except L4
-
FR Wheel Speed
Front speed sensor RH reading/ Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)
Actual wheel speed
No large fluctuations when driving at a constant speed.
FL Wheel Speed
Front speed sensor LH reading/ Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)
Actual wheel speed
No large fluctuations when driving at a constant speed.
RR Wheel Speed
Rear speed sensor RH reading/ Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)
Actual wheel speed
No large fluctuations when driving at a constant speed.
RL Wheel Speed
Rear speed sensor LH reading/ Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)
Actual wheel speed
No large fluctuations when driving at a constant speed.
Vehicle Speed
Maximum wheel speed sensor reading/ Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)
Actual vehicle speed
No large fluctuations when driving at a constant speed.
FR Wheel Acceleration
Front wheel acceleration RH/ Min.: -200.84 m/s2, Max.: 199.27 m/s2
-
Changes continuously during acceleration/deceleration.
FL Wheel Acceleration
Front wheel acceleration LH/ Min.: -200.84 m/s2, Max.: 199.27 m/s2
-
Changes continuously during acceleration/deceleration.
RR Wheel Acceleration
Rear wheel acceleration RH/ Min.: -200.84 m/s2, Max.: 199.27 m/s2
-
Changes continuously during acceleration/deceleration.
RL Wheel Acceleration
Rear wheel acceleration LH/ Min.: -200.84 m/s2, Max.: 199.27 m/s2
-
Changes continuously during acceleration/deceleration.
FR Wheel Direction
Front wheel direction RH/ Forward or Back
Forward: Forward
Back: Back
-
FL Wheel Direction
Front wheel direction LH/ Forward or Back
Forward: Forward
Back: Back
-
RR Wheel Direction
Rear wheel direction RH/ Forward or Back
Forward: Forward
Back: Back
-
RL Wheel Direction
Rear wheel direction LH/ Forward or Back
Forward: Forward
Back: Back
-
FR Wheel ABS Ctrl Status
Front wheel RH ABS control status/ ON or OFF
ON: During control
OFF: Not during control
-
FL Wheel ABS Ctrl Status
Front wheel LH ABS control status/ ON or OFF
ON: During control
OFF: Not during control
-
RR Wheel ABS Ctrl Status
Rear wheel RH ABS control status/ ON or OFF
ON: During control
OFF: Not during control
-
RL Wheel ABS Ctrl Status
Rear wheel LH ABS control status/ ON or OFF
ON: During control
OFF: Not during control
-
RR Wheel EBD Ctrl Status
Rear wheel RH EBD control status/ ON or OFF
ON: During control
OFF: Not during control
-
RL Wheel EBD Ctrl Status
Rear wheel LH EBD control status/ ON or OFF
ON: During control
OFF: Not during control
-
BA Ctrl Status
BA control status/ ON or OFF
ON: During control
OFF: Not during control
-
Engine Revolutions
Engine speed/ Min.: 0 rpm, Max.: 65535 rpm
Actual engine speed
-
Real Engine Torque
Actual engine torque/ Min.: -1024.0 Nm, Max.: 1023.0 Nm
-
-
Accelerator Opening Angle %
Percentage of accelerator pedal opening angle/ Min.: 0.0%, Max.: 128.0%
When accelerator pedal released: 0%
Changes in proportion with the movement of the pedal during accelerator pedal operation.
Solenoid Relay
Solenoid relay/ ON or OFF
ON: Solenoid relay on
OFF: Solenoid relay off
-
ECB* Motor Relay
Motor relay/ ON or OFF
ON: Motor relay on
OFF: Motor relay off
-
TR(A)C/VSC Solenoid (SRM2)
TRC/VSC solenoid (SRM2)/ ON or OFF
ON: Operating
OFF: Not operating
-
TR(A)C/VSC Solenoid (SRM1)
TRC/VSC solenoid (SRM1)/ ON or OFF
ON: Operating
OFF: Not operating
-
TR(A)C/VSC Solenoid (SRC2)
TRC/VSC solenoid (SRC2)/ ON or OFF
ON: Operating
OFF: Not operating
-
TR(A)C/VSC Solenoid (SRC1)
TRC/VSC solenoid (SRC1)/ ON or OFF
ON: Operating
OFF: Not operating
-
ABS Solenoid (SFRH)
ABS solenoid (SFRH)/ ON or OFF
ON: Operating
OFF: Not operating
-
ABS Solenoid (SFRR)
ABS solenoid (SFRR)/ ON or OFF
ON: Operating
OFF: Not operating
-
ABS Solenoid (SFLH)
ABS solenoid (SFLH)/ ON or OFF
ON: Operating
OFF: Not operating
-
ABS Solenoid (SFLR)
ABS solenoid (SFLR)/ ON or OFF
ON: Operating
OFF: Not operating
-
ABS Solenoid (SRRH)
ABS solenoid (SRRH)/ ON or OFF
ON: Operating
OFF: Not operating
-
ABS Solenoid (SRRR)
ABS solenoid (SRRR)/ ON or OFF
ON: Operating
OFF: Not operating
-
ABS Solenoid (SRLH)
ABS solenoid (SRLH)/ ON or OFF
ON: Operating
OFF: Not operating
-
ABS Solenoid (SRLR)
ABS solenoid (SRLR)/ ON or OFF
ON: Operating
OFF: Not operating
-
FR Speed Open
Front speed sensor RH open circuit detection/ Error or Normal
Normal
-
FL Speed Open
Front speed sensor LH open circuit detection/ Error or Normal
Normal
-
RR Speed Open
Rear speed sensor RH open circuit detection/ Error or Normal
Normal
-
RL Speed Open
Rear speed sensor LH open circuit detection/ Error or Normal
Normal
-
EFI Communication Open
ECM communication open circuit detection/ Error or Normal
Normal
-
Deceleration Open
Deceleration sensor open circuit detection/ Error or Normal
Normal
-
Master Cylinder Open
Master cylinder pressure sensor open circuit detection/ Error or Normal
Normal
-
IG1 Voltage Value
IG1 voltage value/ Min.: 0.00 V, Max.: 20.00 V
Ignition switch ON: 11 to 14 V
-
IG2 Voltage Value
IG2 voltage value/ Min.: 0.00 V, Max.: 20.00 V
Ignition switch ON: 11 to 14 V
-
Number of DTC
Number of DTCs/ Min.: 0, Max.: 255
0
-
IG Voltage Value Decreased
IG voltage value decreased detection/ Error or Normal
Normal
-
IG Voltage Value Increased
IG voltage value increased detection/ Error or Normal
Normal
-
FR Speed Sensor Voltage Open
Front speed sensor RH voltage open circuit detection/ Error or Normal
Normal
-
FL Speed Sensor Voltage Open
Front speed sensor LH voltage open circuit detection/ Error or Normal
Normal
-
RR Speed Sensor Voltage Open
Rear speed sensor RH voltage open circuit detection/ Error or Normal
Normal
-
RL Speed Sensor Voltage Open
Rear speed sensor LH voltage open circuit detection/ Error or Normal
Normal
-
M/C Pressure Sensor Noise
Master cylinder pressure sensor noise detection/ Error or Normal
Normal
-
EFI Communication Invalid
ECM communication invalid detection/ Error or Normal
Normal
-
- *: Electronically Controlled Brake
- *: Electronically Controlled Brake
| ACTIVE TEST |
- HINT:
- Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
Warm up the engine.
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Chassis / ABS/VSC/TRC / Active Test.
According to the display on the GTS, perform the Active Test.
| Tester Display |
Test Part |
Control Range |
Diagnostic Note |
| ABS Warning Light |
ABS warning light |
Warning light ON/OFF |
Observe the combination meter. |
| Brake Warning Light |
Brake warning light |
Warning light ON/OFF |
Observe the combination meter. |
| Buzzer |
Buzzer |
Buzzer ON/OFF |
The buzzer can be heard. |
| Solenoid Relay |
Solenoid relay |
Relay ON/OFF |
An operating sound of the solenoid (clicking sound) can be heard. |
| Motor Relay |
Motor relay |
Relay ON/OFF |
An operating sound of the solenoid of the motor can be heard. |
| ABS Solenoid (SRLR) |
ABS solenoid (SRLR) |
Solenoid ON/OFF |
An operating sound of the solenoid (clicking sound) can be heard. |
| ABS Solenoid (SRLH) |
ABS solenoid (SRLH) |
Solenoid ON/OFF |
An operating sound of the solenoid (clicking sound) can be heard. |
| ABS Solenoid (SRRR) |
ABS solenoid (SRRR) |
Solenoid ON/OFF |
An operating sound of the solenoid (clicking sound) can be heard. |
| ABS Solenoid (SRRH) |
ABS solenoid (SRRH) |
Solenoid ON/OFF |
An operating sound of the solenoid (clicking sound) can be heard. |
| ABS Solenoid (SFLR) |
ABS solenoid (SFLR) |
Solenoid ON/OFF |
An operating sound of the solenoid (clicking sound) can be heard. |
| ABS Solenoid (SFLH) |
ABS solenoid (SFLH) |
Solenoid ON/OFF |
An operating sound of the solenoid (clicking sound) can be heard. |
| ABS Solenoid (SFRR) |
ABS solenoid (SFRR) |
Solenoid ON/OFF |
An operating sound of the solenoid (clicking sound) can be heard. |
| ABS Solenoid (SFRH) |
ABS solenoid (SFRH) |
Solenoid ON/OFF |
An operating sound of the solenoid (clicking sound) can be heard. |
| VSC/TRC Solenoid (SRMR) |
VSC/TRC solenoid (SRM2) |
Solenoid ON/OFF |
An operating sound of the solenoid (clicking sound) can be heard. |
| VSC/TRC Solenoid (SRMF) |
VSC/TRC solenoid (SRM1) |
Solenoid ON/OFF |
An operating sound of the solenoid (clicking sound) can be heard. |
| VSC/TRC Solenoid (SRCR) |
VSC/TRC solenoid (SRC2) |
Solenoid ON/OFF |
An operating sound of the solenoid (clicking sound) can be heard. |
| VSC/TRC Solenoid (SRCF) |
VSC/TRC solenoid (SRC1) |
Solenoid ON/OFF |
An operating sound of the solenoid (clicking sound) can be heard. |
| ABS Solenoid |
Selection of multiple holding solenoids (SFRH, SFLH, SRRH and SRLH) and pressure reduction solenoids (SFRR, SFLR, SRRR and SRLR) possible |
Start/Stop |
- |
| VSC/TRC Solenoid |
Selection of multiple VSC/TRC solenoids [SRMR (SRM2), SRMF (SRM1), SRCR (SRC2) and SRCF (SRC1)] possible |
Start/Stop |
- |