2011-2013 Land Cruiser · Service Manual Brake

CALIBRATION

Troubleshooting · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012


DESCRIPTION
After replacing the relevant VSC components or performing a vehicle height adjustment, clear the sensor calibration data and perform calibration.
Replacement/Adjustment Part
Necessary Operation
Master cylinder solenoid (Skid control ECU)
Yaw rate and G sensor zero point calibration
Yaw rate and G sensor
1. Clearing zero point calibration data
2. Yaw rate and G sensor zero point calibration
Vehicle height adjustment
1. Clearing zero point calibration data
2. Yaw rate and G sensor zero point calibration
3. Steering angle sensor initialization

CLEAR ZERO POINT CALIBRATION (SST CHECK WIRE)
After replacing the yaw rate and G sensor or performing a vehicle height adjustment, make sure to clear the zero point calibration data in the skid control ECU and perform zero point calibration.
  1. Turn the ignition switch to ON.

  2. C166029E02
    Using SST, connect and disconnect terminals 12 (TS) and 4 (CG) of the DLC3 4 times or more within 8 seconds.
    SST
    09843-18040  

  3. C173109E01
    Check that "DIAG VSC OK" is displayed on the multi-information display*1 and check that the ABS warning light and VSC OFF indicator light*2 output the normal system code.

    HINT:
    *1: w/ Multi-information Display
    *2: w/o Multi-information Display

  4. Using a check wire, perform zero point calibration of the yaw rate and G sensor.


PERFORM ZERO POINT CALIBRATION OF YAW RATE AND G SENSOR (SST CHECK WIRE)
After replacing the master cylinder solenoid and/or yaw rate and G sensor or performing a vehicle height adjustment, make sure to perform yaw rate and G sensor zero point calibration.

NOTICE:
  1. While obtaining the zero point, do not vibrate the vehicle by tilting, moving or shaking it. Keep it stationary and do not start the engine.
  2. Choose a level surface with an inclination of less than 1°.

  1. Procedures for Test Mode:

    1. Turn the ignition switch off.

    2. Move the shift lever to P.

      NOTICE:
      DTC C1210/36 and C1336/98 will be stored if the shift lever is not in P (Click here).

    3. C166029E02
      Using SST, connect terminals 12 (TS) and 4 (CG) of the DLC3.
      SST
      09843-18040  

    4. Check that the steering wheel is centered.

    5. Turn the ignition switch to ON.

    6. Keep the vehicle stationary on a level surface for 2 seconds or more.

    7. C173109E02
      Check that "VSC TEST MODE" is displayed on the multi-information display*1 and check that the ABS warning light and VSC OFF indicator light*2 are blinking in test mode.

      NOTICE:
      The ABS warning light and VSC OFF indicator light*2 stay on when obtaining the zero point.

      HINT:
      1. If the ABS warning light and VSC OFF indicator light*2 do not blink, perform the zero point calibration again.
      2. The zero point calibration is performed only once after the system enters test mode.
      3. Calibration cannot be performed again until the stored data is cleared once.
      4. *1: w/ Multi-information Display
      5. *2: w/o Multi-information Display


CLEAR ZERO POINT CALIBRATION (INTELLIGENT TESTER)
After replacing the yaw rate and G sensor or performing a vehicle height adjustment, make sure to clear the zero point calibration data in the skid control ECU and perform zero point calibration.
  1. Connect the intelligent tester to the DLC3.

  2. Turn the ignition switch to ON.

  3. Turn the intelligent tester on.

  4. Enter the following menus: Chassis / ABS/VSC/TRC / Utility / Reset Memory.

  5. Using the intelligent tester, perform zero point calibration of the yaw rate and G sensor.


PERFORM ZERO POINT CALIBRATION OF YAW RATE AND G SENSOR (INTELLIGENT TESTER)
After replacing the master cylinder solenoid and/or yaw rate and G sensor or performing a vehicle height adjustment, make sure to perform yaw rate and G sensor zero point calibration.

NOTICE:
  1. While obtaining the zero point, do not vibrate the vehicle by tilting, moving or shaking it. Keep it stationary and do not start the engine.
  2. Choose a level surface with an inclination of less than 1°.

  1. Procedures for Test Mode:

    1. Turn the ignition switch off.

    2. Move the shift lever to P.

      NOTICE:
      DTC C1210/36 and C1336/98 will be stored if the shift lever is not in P (Click here).

    3. Check that the steering wheel is centered.

    4. Connect the intelligent tester to the DLC3.

    5. Turn the ignition switch to ON.

    6. Turn the intelligent tester on.

    7. Enter the following menus: Chassis / ABS/VSC/TRC / Utility / Test Mode.

    8. Keep the vehicle stationary on a level surface for 2 seconds or more.

    9. C173109E02
      Check that "VSC TEST MODE" is displayed on the multi-information display*1 and check that the ABS warning light and VSC OFF indicator light*2 are blinking in test mode.

      NOTICE:
      The ABS warning light and VSC OFF indicator light*2 stay on when obtaining the zero point.

      HINT:
      1. If the ABS warning light and VSC OFF indicator light*2 do not blink, perform the zero point calibration again.
      2. The zero point calibration is performed only once after the system enters test mode.
      3. Calibration cannot be performed again until the stored data is cleared once.
      4. *1: w/ Multi-information Display
      5. *2: w/o Multi-information Display

← CHECK FOR INTERMITTENT PROBLEMS (from Jan 2012)CALIBRATION (from Jan 2012) →