2011-2013 Land Cruiser · Service Manual Brake

TC and CG Terminal Circuit

Circuit diagnosis · Vehicles built from Jan 2012

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

DESCRIPTION

DTC output mode is set by connecting terminals TC and CG of the DLC3.
The DTCs are output by the blinking of the ABS warning light and slip indicator light.

WIRING DIAGRAM

C256466E05

HINT:
When each warning light stays blinking, a ground short in the wiring of terminal TC of the DLC3 or an internal ground short in each ECU is suspected.


INSPECTION PROCEDURE

NOTICE:
After replacing the master cylinder solenoid, perform zero point calibration and store the system information (Click here).


1. INSPECT DLC3 (DLC3 (TC) - DLC3 (CG))

  1. C245481E06
    Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    E22-13 (TC) - E22-4 (CG)
    Ignition switch ON
    11 to 14 V

    Text in Illustration  
    *1
    DLC3



NG
Go to step 4
OK


2. CHECK CAN COMMUNICATION LINE
  1. Turn the ignition switch off.

  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON and the GTS on.

  1. Select "CAN Bus Check" from the System Selection Menu screen, and follow the prompts on the screen to inspect the CAN Bus.

    OK:
    "CAN Bus Check" indicates no malfunctions in CAN communication.

    Result 
    Result
    Proceed to
    OK
    A
    NG (for LHD)
    B
    NG (for RHD)
    C



B
GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) (Click here)

C
GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) (Click here)
A


3. CHECK DTC (CAN COMMUNICATION SYSTEM)
  1. Turn the ignition switch off.

  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON and the GTS on.

  1. Check for DTCs (for LHD: Click here, for RHD: Click here).

    Result 
    Result
    Proceed to
    CAN system DTC is not output
    A
    CAN system DTC is output (for LHD)
    B
    CAN system DTC is output (for RHD)
    C



B
GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) (Click here)

C
GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) (Click here)
A


4. CHECK HARNESS AND CONNECTOR (ECM - DLC3 (TC))
  1. Turn the ignition switch off.

  1. for LHD:

    1. Disconnect the A38 ECM connector.

  1. for RHD:

    1. Disconnect the A52 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LHD (1UR-FE and 3UR-FE): 
    Tester Connection
    Condition
    Specified Condition
    A38-16 (TC) - E22-13 (TC)
    Always
    Below 1 Ω
    for RHD (1UR-FE): 
    Tester Connection
    Condition
    Specified Condition
    A52-16 (TC) - E22-13 (TC)
    Always
    Below 1 Ω
    for LHD (1VD-FTV): 
    Tester Connection
    Condition
    Specified Condition
    A38-27 (TC) - E22-13 (TC)
    Always
    Below 1 Ω
    for RHD (1VD-FTV): 
    Tester Connection
    Condition
    Specified Condition
    A52-27 (TC) - E22-13 (TC)
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5. CHECK HARNESS AND CONNECTOR (DLC3 (CG) - BODY GROUND)

  1. C245481E13
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E22-4 (CG) - Body ground
    Always
    Below 1 Ω

    Text in Illustration  
    *1
    DLC3



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6. CHECK ECM (DLC3 (TC) INPUT)

  1. C245481E06
    Using SST, connect terminals TC and CG of the DLC3.

  1. Check that the malfunction indicator lamp is blinking.

    Result 
    Result
    Proceed to
    MIL is blinking
    A
    MIL is not blinking
    B
    Text in Illustration  
    *1
    DLC3



B
REPAIR OR REPLACE WIRE HARNESS OR ECM
A


7. CHECK DTC (CAN COMMUNICATION SYSTEM)
  1. Turn the ignition switch off.

  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON and the GTS on.

  1. Check for DTCs (for LHD: Click here, for RHD: Click here).

    Result 
    Result
    Proceed to
    CAN system DTC is not output (for LHD)
    A
    CAN system DTC is not output (for RHD)
    B
    CAN system DTC is output (for LHD)
    C
    CAN system DTC is output (for RHD)
    D



B
REPLACE MASTER CYLINDER SOLENOID (Click here)

C
GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) (Click here)

D
GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) (Click here)
A

REPLACE MASTER CYLINDER SOLENOID (Click here)


← TC and CG Terminal Circuit (Sep 2011 – Dec 2011)TS and CG Terminal Circuit (Sep 2011 – Dec 2011) →