2011-2013 Land Cruiser · Service Manual Brake

Crawl Indicator Light Remains ON

Circuit diagnosis · Vehicles built from Jan 2012

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

DESCRIPTION

When CRAWL starts after operating the CRAWL switch, the CRAWL indicator light turns on. While CRAWL is in the process of stopping, the CRAWL indicator light begins blinking. When CRAWL totally stops, the CRAWL indicator light turns off.

WIRING DIAGRAM

C256732E01

INSPECTION PROCEDURE

NOTICE:
After replacing the master cylinder solenoid, perform zero point calibration and store the system information (Click here).


1. CHECK CAN COMMUNICATION LINE
  1. Turn the ignition switch off.

  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON and the GTS on.

  1. Select "CAN Bus Check" from the System Selection Menu screen, and follow the prompts on the screen to inspect the CAN Bus.

    OK:
    "CAN Bus Check" indicates no malfunctions in CAN communication.

    Result 
    Result
    Proceed to
    OK
    A
    NG (for LHD)
    B
    NG (for RHD)
    C



B
GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) (Click here)

C
GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) (Click here)
A


2. CHECK DTC (CAN COMMUNICATION SYSTEM)
  1. Turn the ignition switch off.

  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON and the GTS on.

  1. Check for DTCs (for LHD: Click here, for RHD: Click here).

    Result 
    Result
    Proceed to
    CAN system DTC is not output
    A
    CAN system DTC is output (for LHD)
    B
    CAN system DTC is output (for RHD)
    C



B
GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) (Click here)

C
GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) (Click here)
A


3. PERFORM ACTIVE TEST USING GTS (CRAWL CONTROL LIGHT)
  1. Turn the ignition switch off.

  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the GTS on.

  1. Enter the following menus: Chassis / ABS/VSC/TRC / Active Test.

    ABS/VSC/TRC 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Crawl Control Light
    CRAWL indicator light
    Indicator light ON/OFF
    Observe the combination meter.

  1. When performing the Crawl Control Light Active Test, check Crawl Control Light in the Data List.

    ABS/VSC/TRC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Crawl Control Light
    CRAWL indicator light/ ON or OFF
    ON: Indicator light on
    OFF: Indicator light off
    -
    Result 
    Result
    Proceed to
    Data List Display
    Data List Display when Performing Active Test ON/OFF Operation
    ON
    Changes between ON and OFF
    A
    Does not change between ON and OFF (for LHD)
    B
    Does not change between ON and OFF (for RHD)
    C
    OFF
    Changes between ON and OFF
    A
    Does not change between ON and OFF (for LHD)
    B
    Does not change between ON and OFF (for RHD)
    C



B
REPLACE MASTER CYLINDER SOLENOID (Click here)

C
REPLACE MASTER CYLINDER SOLENOID (Click here)
A

GO TO METER / GAUGE SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) (Click here)


← Crawl Indicator Light Remains ON (Sep 2011 – Dec 2011)Crawl Indicator Light does not Come ON (Sep 2011 – Dec 2011) →