2011-2013 Land Cruiser · Service Manual Engine / Hybrid / EV System

P0550 Power Steering Pressure Sensor Circuit Malfunction

Diagnostic trouble codes · Vehicles built from Jan 2012

Also covers:

DESCRIPTION

The power steering oil pressure sensor is turned on when a power steering wheel load is generated by turning the steering wheel. The ECM regulates the engine idling speed according to the voltage output of the sensor.
DTC No.
DTC Detection Condition
Trouble Area
P0550
Power steering oil pressure sensor voltage is below 0.28 V, or higher than 4.9 V for 0.5 seconds while the engine is running (1 trip detection logic).
  1. Open or short in power steering oil pressure sensor circuit
  2. Power steering oil pressure sensor
  3. ECM
P0552
Power steering oil pressure sensor voltage is below 0.28 V for 0.5 seconds while the engine is running (1 trip detection logic).
  1. Open or short in power steering oil pressure sensor circuit
  2. Power steering oil pressure sensor
  3. ECM
P0553
Power steering oil pressure sensor voltage is higher than 4.9 V for 0.5 seconds while the engine is running (1 trip detection logic).
  1. Open or short in power steering oil pressure sensor circuit
  2. Power steering oil pressure sensor
  3. ECM

MONITOR DESCRIPTION

The ECM monitors the power steering oil pressure sensor voltage and uses this value to regulate the engine idling speed. When the power steering oil pressure sensor output voltage deviates from the normal operating range, the ECM determines that there is a malfunction in the power steering oil pressure sensor and stores a DTC.

WIRING DIAGRAM

A162851E14

INSPECTION PROCEDURE

HINT:
  1. If DTCs relating to different systems which share terminal E2 as their ground are stored simultaneously, there may be an open circuit between terminal E2 and ground.
  2. Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


1. CHECK HARNESS AND CONNECTOR (ECM - POWER STEERING OIL PRESSURE SENSOR)
  1. Disconnect the ECM connector.

  1. Disconnect the power steering oil pressure sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LHD 
    Tester Connection
    Condition
    Specified Condition
    C59-2 (PSP) - C45-72 (PSP)
    Always
    Below 1 Ω
    C59-1 (VC) - C45-66 (VCV2)
    Always
    Below 1 Ω
    C59-3 (E2) - C45-97 (ETHW)
    Always
    Below 1 Ω
    C59-2 (PSP) or C45-72 (PSP) - Body ground
    Always
    10 kΩ or higher
    C59-1 (VC) or C45-66 (VCV2) - Body ground
    Always
    10 kΩ or higher
    for RHD 
    Tester Connection
    Condition
    Specified Condition
    C59-2 (PSP) - C46-72 (PSP)
    Always
    Below 1 Ω
    C59-1 (VC) - C46-66 (VCV2)
    Always
    Below 1 Ω
    C59-3 (E2) - C46-97 (ETHW)
    Always
    Below 1 Ω
    C59-2 (PSP) or C46-72 (PSP) - Body ground
    Always
    10 kΩ or higher
    C59-1 (VC) or C46-66 (VCV2) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2. REPLACE POWER STEERING OIL PRESSURE SENSOR
  1. Replace the power steering oil pressure sensor (Click here).


NEXT


3. CONFIRM WHETHER DTC OUTPUT RECURS
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the GTS on.

  1. Start the engine.

  1. Idle the engine for 5 seconds.

  1. Read the DTCs.

    Result 
    Result
    Proceed to
    P0550, P0552 and/or P0553 is output
    A
    No DTC is output
    B



B
END
A

REPLACE ECM (Click here)


← P0505 Idle Control System Malfunction (Sep 2011 – Dec 2011)P0560 System Voltage (Sep 2011 – Dec 2011) →