2011-2013 Land Cruiser · Service Manual Engine / Hybrid / EV System

P0560 System Voltage

Diagnostic trouble codes · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

DESCRIPTION

The battery supplies electricity to the ECM even when the ignition switch is off. This power allows the ECM to store data such as DTC history, freeze frame data and fuel trim values. If the battery voltage falls below a minimum level, the memory is cleared and the ECM determines that there is a malfunction in the power supply circuit. When the engine is next started, the ECM illuminates the MIL and stores the DTC.
DTC Code
DTC Detection Condition
Trouble Area
P0560
An open in the ECM back up power source circuit (1 trip detection logic).
  1. Open in back up power source circuit
  2. Battery
  3. Battery terminals
  4. EFI MAIN fuse
  5. ECM

HINT:
If DTC P0560 is stored, the ECM does not store other DTCs or the data stored in the ECM is partly cleared.


WIRING DIAGRAM

A162661E03
A162661E04

INSPECTION PROCEDURE

HINT:
Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


1. INSPECT FUSE (EFI MAIN)
A162283E03
  1. Remove the EFI MAIN fuse from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    EFI MAIN fuse
    Always
    Below 1 Ω



NG
CHECK FOR SHORTS IN ALL HARNESSES AND CONNECTORS CONNECTED TO FUSE AND REPLACE FUSE
OK


2. CHECK HARNESS AND CONNECTOR (ECM - EFI MAIN FUSE, EFI MAIN FUSE - BATTERY)
A162155E03
  1. Check the harness and the connector between the EFI MAIN fuse and ECM.

    1. Remove the EFI MAIN fuse from the engine room relay block.

    2. Disconnect the ECM connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance (Check for Open):
      for LHD 
      Tester Connection
      Condition
      Specified Condition
      EFI MAIN fuse (2) - A38-20 (BATT)
      Always
      Below 1 Ω
      for RHD 
      Tester Connection
      Condition
      Specified Condition
      EFI MAIN fuse (2) - A52-20 (BATT)
      Always
      Below 1 Ω


      Standard Resistance (Check for Short):
      for LHD 
      Tester Connection
      Condition
      Specified Condition
      EFI MAIN fuse (2) or A38-20 (BATT) - Body ground
      Always
      10 kΩ or higher
      for RHD 
      Tester Connection
      Condition
      Specified Condition
      EFI MAIN fuse (2) or A52-20 (BATT) - Body ground
      Always
      10 kΩ or higher

  1. Check the harness and the connector between the EFI MAIN fuse and battery.

    1. Remove the EFI MAIN fuse from the engine room relay block.

    2. Disconnect the cable from the positive (+) battery terminal.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance (Check for Open):
      Tester Connection
      Condition
      Specified Condition
      Battery positive terminal - EFI MAIN fuse (1)
      Always
      Below 1 Ω

      Standard Resistance (Check for Short):
      Tester Connection
      Condition
      Specified Condition
      Battery positive terminal or EFI MAIN fuse (1) - Body ground
      Always
      10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. INSPECT BATTERY
  1. Check that the battery is not depleted.

    OK:
    Battery is not depleted.



NG
REPLACE BATTERY
OK


4. CHECK BATTERY TERMINAL
  1. Check that the battery terminals are not loose or corroded.

    OK:
    Battery terminals are not loose or corroded.



NG
REPAIR OR REPLACE BATTERY TERMINAL
OK


5. CHECK WHETHER DTC OUTPUT RECURS
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off and turn the tester off.

  1. Start the engine and turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read the DTCs.

    Result 
    Result
    Proceed to
    P0560
    A
    No output
    B



B
CHECK FOR INTERMITTENT PROBLEMS (Click here)
A

REPLACE ECM (Click here)


← P0550 Power Steering Pressure Sensor Circuit Malfunction (+ P0552, P0553) (from Jan 2012)P0560 System Voltage (from Jan 2012) →