2011-2013 Land Cruiser · Service Manual Vehicle Interior

Air Conditioning Control Panel does not Operate

Circuit diagnosis · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

DESCRIPTION

This circuit* consists of the air conditioning control assembly and the air conditioning amplifier assembly. When the air conditioning control assembly is operated, signals are transmitted to the air conditioning amplifier assembly through the LIN communication system.
If the LIN communication system malfunctions, the air conditioning amplifier assembly does not operate even if the air conditioning control assembly is operated.

HINT:
*: w/o Multi-display


WIRING DIAGRAM

E157369E08
E157369E09

INSPECTION PROCEDURE


1. INSPECT FUSE (ECU-IG NO. 2)
  1. Remove the ECU-IG NO. 2 fuse from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    ECU-IG NO. 2 fuse
    Always
    Below 1 Ω



NG
REPLACE FUSE
OK


2. CHECK HARNESS AND CONNECTOR (AIR CONDITIONING CONTROL - BODY GROUND AND BATTERY)
E157365E01
  1. Disconnect the F10 air conditioning control assembly connector.

  1. Measure the resistance and voltage according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F10-1 (GND) - Body ground
    Always
    Below 1 Ω

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    F10-1 (GND) - F10-7 (IG+)
    Engine switch on (IG)
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER - AIR CONDITIONING CONTROL)

  1. E157366E03
    w/ Rear Heater
    1. Disconnect the F10 air conditioning control assembly connector.

    2. Disconnect the E36 amplifier connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      E36-20 (LIN1) - F10-5 (LIN1)
      Always
      Below 1 Ω
      E36-20 (LIN1) - Body ground
      Always
      10 kΩ or higher

  1. E160297E02
    w/o Rear Heater
    1. Disconnect the F10 air conditioning control assembly connector.

    2. Disconnect the E81 amplifier connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      E81-37 (LIN1) - F10-5 (LIN1)
      Always
      Below 1 Ω
      E81-37 (LIN1) - Body ground
      Always
      10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. CHECK AIR CONDITIONING CONTROL ASSEMBLY (OPERATION)
  1. Replace the air conditioning control assembly with a new or properly functioning one.

  1. Operate the front air conditioning control to check that it functions properly.

    OK:
    Air conditioning control assembly function operates normally.



NG
REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)
OK

REPLACE AIR CONDITIONING CONTROL ASSEMBLY (Click here)


← U0100 Lost Communication with ECM / PCM "A" (+ U0142, U0155) (from Jan 2012)Air Conditioning Control Panel does not Operate (from Jan 2012) →