TERMINALS OF ECU
System information · Vehicles built from Sep 2011
| CHECK MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY |


for Models with Jam Protection Function on 4 Windows
Disconnect the I11*1 or I22*2 switch connector.
- HINT:
- *1: for LHD
- *2: for RHD
Measure the voltage and resistance according to the value(s) in the table below.
Terminal No. (Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
I11-12 (GND) - Body ground*1
W-B - Body ground
Ground
Always
Below 1 Ω
I11-11 (B) - I11-12 (GND)*1
L - W-B
Battery power supply
Always
11 to 14 V
I22-12 (GND) - Body ground*2
W-B - Body ground
Ground
Always
Below 1 Ω
I22-11 (B) - I22-12 (GND)*2
L - W-B
Battery power supply
Always
11 to 14 V
- HINT:
- *1: for LHD
- *2: for RHD
for Models with Jam Protection Function on Driver Door Window Only
Disconnect the I31*1 or I26*2 switch connector.
- HINT:
- *1: for LHD
- *2: for RHD
Measure the voltage and resistance according to the value(s) in the table below.
Terminal No. (Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
I31-1 (E) - Body ground*1
W-B - Body ground
Ground
Always
Below 1 Ω
I31-6 (B) - I31-1 (E)*1
L - W-B
Battery power supply
Always
11 to 14 V
I26-9 (E) - Body ground*2
W-B - Body ground
Ground
Always
Below 1 Ω
I26-6 (B) - I26-9 (E)*2
L - W-B
Battery power supply
Always
11 to 14 V
- HINT:
- *1: for LHD
- *2: for RHD
| CHECK MAIN BODY ECU (COWL SIDE JUNCTION BLOCK LH) |


Disconnect the 2A, 2B and 2D ECU connectors.
Measure the voltage and resistance according to the value(s) in the table below.
If the result is not as specified, there may be a malfunction on the wire harness side.Terminal No. (Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
2B-20 (BATB) - Body ground
L - Body ground
Battery power supply
Always
11 to 14 V
2A-1 (ACC) - Body ground
B - Body ground
ACC power supply
Ignition switch ACC
11 to 14 V
2A-1 (ACC) - Body ground
B - Body ground
ACC power supply
Ignition switch off
Below 1 Ω
2D-62 (GND2) - Body ground
W-B - Body ground
Ground
Always
Below 1 Ω
Reconnect the 2A, 2B and 2D ECU connectors.
Measure the voltage according to the value(s) in the table below.
Terminal No. (Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
E1-24 (DCTY) - Body ground
L*1 - Body ground
Y*2 - Body ground
Driver side door courtesy switch input
Driver side door open
Below 1 V
E1-24 (DCTY) - Body ground
L*1 - Body ground
Y*2 - Body ground
Driver side door courtesy switch input
Ignition switch off, and driver side door courtesy switch off
Pulse generation
E2-21 (PCTY) - Body ground
Y*1 - Body ground
L*2 - Body ground
Front passenger side door courtesy switch input
Front passenger side door open
Below 1 V
E2-21 (PCTY) - Body ground
Y*1 - Body ground
L*2 - Body ground
Front passenger side door courtesy switch input
Ignition switch off, and passenger side door courtesy switch off
Pulse generation
2C-2 (LCTY) - Body ground
W - Body ground
Rear door LH courtesy light switch input
Rear door LH open
Below 1 V
2C-2 (LCTY) - Body ground
W - Body ground
Rear door LH courtesy light switch input
Ignition switch off, and rear LH side door courtesy switch off
Pulse generation
E2-7 (RCTY) - Body ground
*3
G - Body ground
Rear door RH courtesy light switch input
Rear door RH open
Below 1 V
E2-7 (RCTY) - Body ground
*3
G - Body ground
Rear door RH courtesy light switch input
Ignition switch off, and rear RH side door courtesy switch off
Pulse generation
E1-17 (RCTY) - Body ground
*4
G - Body ground
Rear door RH courtesy light switch input
Rear door RH open
Below 1 V
E1-17 (RCTY) - Body ground
*4
G - Body ground
Rear door RH courtesy light switch input
Ignition switch off, and rear RH side door courtesy switch off
Pulse generation
E2-25 (BCTY) - Body ground
W - Body ground
Back door courtesy light switch input
Back door open
Below 1 V
E2-25 (BCTY) - Body ground
W - Body ground
Back door courtesy light switch input
Ignition switch off, and back door closed
Pulse generation
2D-3 (ACT+) - Body ground
L - Body ground
Door lock motor LOCK drive output
Master switch (door control switch) or driver side door key cylinder in neutral position
Below 1 V
2D-3 (ACT+) - Body ground
L - Body ground
Door lock motor LOCK drive output
Master switch (door control switch) or driver side door key cylinder in lock position
11 to 14 V
2C-24 (ACT+) - Body ground
L - Body ground
Door lock motor LOCK drive output
Master switch (door control switch) or driver side door key cylinder in neutral position
Below 1 V
2C-24 (ACT+) - Body ground
L - Body ground
Door lock motor LOCK drive output
Master switch (door control switch) or driver side door key cylinder in lock position
11 to 14 V
E1-5 (ACTD) - Body ground
B - Body ground
Door lock motor UNLOCK drive output
Master switch (door control switch) or driver side door key cylinder in neutral position
Below 1 V
E1-5 (ACTD) - Body ground
B - Body ground
Door lock motor UNLOCK drive output
Master switch (door control switch) or driver side door key cylinder in unlock position
11 to 14 V
2D-2 (ACT-) - Body ground
B - Body ground
Door lock motor UNLOCK drive output
Master switch (door control switch) or driver side door key cylinder in neutral position
Below 1 V
2D-2 (ACT-) - Body ground
B - Body ground
Door lock motor UNLOCK drive output
Master switch (door control switch) or driver side door key cylinder in unlock position
11 to 14 V
2C-23 (ACT-) - Body ground
B - Body ground
Door lock motor UNLOCK drive output
Master switch (door control switch) or driver side door key cylinder in neutral position
Below 1 V
2C-23 (ACT-) - Body ground
B - Body ground
Door lock motor UNLOCK drive output
Master switch (door control switch) or driver side door key cylinder in unlock position
11 to 14 V
E1-10 (UL3) - Body ground
Y*1 - Body ground
L*2 - Body ground
Driver side door lock key switch input
Driver side door key cylinder in unlock position
Below 1 V
E1-10 (UL3) - Body ground
Y*1 - Body ground
L*2 - Body ground
Driver side door lock key switch input
Ignition switch off, all doors closed and driver side door key cylinder in neutral position
Pulse generation
2D-53 (L2) - Body ground
LG - Body ground
Driver side door lock key switch input
Driver side door key cylinder in lock position
Below 1 V
2D-53 (L2) - Body ground
LG - Body ground
Driver side door lock key switch input
Ignition switch off, all doors closed and driver side door key cylinder in neutral position
Pulse generation
2D-52 (UL1) - Body ground
*4
W - Body ground
Master switch (door control switch) input
Master switch (door control switch) in unlock position
Below 1 V
2D-52 (UL1) - Body ground
*4
W - Body ground
Master switch (door control switch) input
Master switch (door control switch) in neutral position
Pulse generation
2D-49 (L1) - Body ground
*4
BE - Body ground
Master switch (door control switch) input
Master switch (door control switch) in unlock position
Below 1 V
2D-49 (L1) - Body ground
*4
BE - Body ground
Master switch (door control switch) input
Master switch (door control switch) in neutral position
Pulse generation
E1-1 (TR+) - Body ground
*3
L - Body ground
Back door lock motor UNLOCK drive output
Master switch (door control switch) or driver side door key cylinder in neutral position
Below 1 V
E1-1 (TR+) - Body ground
*3
L - Body ground
Back door lock motor UNLOCK drive output
Master switch (door control switch) or driver side door key cylinder in unlock position
11 to 14 V
E1-9 (LSWD) - Body ground
BR - Body ground
Driver side door lock position switch input
Driver side door unlocked
Below 1 V
E1-9 (LSWD) - Body ground
BR - Body ground
Driver side door lock position switch input
Ignition switch off, all doors closed and driver side door locked
Pulse generation
E2-27 (LSWP) - Body ground
Y*1 - Body ground
BR*2 - Body ground
Front passenger side door lock position switch input
Front passenger side door unlocked
Below 1 V
E2-27 (LSWP) - Body ground
Y*1 - Body ground
BR*2 - Body ground
Front passenger side door lock position switch input
Ignition switch off, all doors closed and passenger side door locked
Pulse generation
2C-1 (LSWL) - Body ground
BR - Body ground
Rear door LH lock position switch input
Rear door LH unlocked
Below 1 V
2C-1 (LSWL) - Body ground
BR - Body ground
Rear door LH lock position switch input
Ignition switch off, all doors closed and rear door LH locked
Pulse generation
E2-5 (LSWR) - Body ground
BR - Body ground
Rear door RH lock position switch input
Rear door RH unlocked
Below 1 V
E2-5 (LSWR) - Body ground
BR - Body ground
Rear door RH lock position switch input
Ignition switch off, all doors closed and rear door RH locked
Pulse generation
E2-2 (LSWB) - Body ground
*4
LG - Body ground
Back door lock position switch input
Back door unlocked
Below 1 V
E2-2 (LSWB) - Body ground
*4
LG - Body ground
Back door lock position switch input
Ignition switch off, all doors closed and back door locked
Pulse generation
E1-26 (BDSU) - Body ground
*3
L - Body ground
Back door opener switch input
Back door lock opener switch off
Below 1 V
E1-26 (BDSU) - Body ground
*3
L - Body ground
Back door opener switch input
Back door lock opener switch on
Pulse generation
- HINT:
- *1: for LHD
- *2: for RHD
- *3: w/ Entry and Start System
- *4: w/o Entry and Start System
| CHECK DOUBLE LOCK DOOR CONTROL RELAY (w/ Double Locking Function) |


Disconnect the E86 double lock door control relay connector.
Measure the voltage according to the value(s) in the table below.
If the result is not as specified, there may be a malfunction on the wire harness side.Terminal No. (Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
E86-1 (+B) - E86-14 (GND)
B - W-B
Battery power supply
Always
11 to 14 V
E86-7 (CPUB) - E86-14 (GND)
R - W-B
ECU power supply
Always
11 to 14 V
E86-14 (GND) - Body ground
W-B - Body ground
Ground
Always
Below 1 V
Reconnect the E86 double lock door control relay connector.
Measure the voltage and resistance according to the value(s) in the table below.
If the result is not as specified, the ECU may have a malfunction.Terminal No. (Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
E86-4 (ACTR) - E86-14 (GND)
P - W-B
All door double lock motor off signal
Door lock set → unset
Below 1 V → 11 to 14 V → Below 1 V
E86-3 (ACTS) - E86-14 (GND)
G - W-B
All door double lock motor on signal
Door lock unset → set
Below 1 V → 11 to 14 V → Below 1 V
E86-5 (DLPD) - E86-14 (GND)
BR - W-B
Double lock position switch signal
Double lock set
Below 1 Ω
E86-5 (DLPD) - E86-14 (GND)
BR - W-B
Double lock position switch signal
Double lock unset
10 kΩ or higher
E86-6 (DLPP) - E86-14 (GND)
GR - W-B
Double lock position switch signal
Double lock set
Below 1 Ω
E86-6 (DLPP) - E86-14 (GND)
GR - W-B
Double lock position switch signal
Double lock unset
10 kΩ or higher
E86-11 (DLPR) - E86-14 (GND)
Y - W-B
Double lock position switch signal
Double lock set
Below 1 Ω
E86-11 (DLPR) - E86-14 (GND)
Y - W-B
Double lock position switch signal
Double lock unset
10 kΩ or higher
E86-12 (DLPL) - E86-14 (GND)
LG - W-B
Double lock position switch signal
Double lock set
Below 1 Ω
E86-12 (DLPL) - E86-14 (GND)
LG - W-B
Double lock position switch signal
Double lock unset
10 kΩ or higher