2011-2013 Land Cruiser · Service Manual Power Source / Network

REASSEMBLY

Removal / installation · Vehicles built from Jan 2012


1. INSTALL GENERATOR DRIVE END FRAME BEARING

  1. A219663E01
    Using SST and a press, press in a new drive end frame bearing.
    SST
    09950-60010   (09951-00470)
    09950-70010   (09951-07100)

  1. A219664E01
    Fit the tabs on the retainer plate into the cutouts on the generator drive end frame to install the retainer plate.
    Text in Illustration 
    *1
    Tab
    *2
    Cutout

  1. Install the 4 screws.

    Torque:
    2.3 N*m{ 23 kgf*cm , 20 in.*lbf }


2. INSTALL GENERATOR ROTOR ASSEMBLY
  1. Install the generator rotor to the generator drive end frame.

  1. Place a new generator washer on the generator rotor.


3. INSTALL GENERATOR COIL ASSEMBLY

  1. A128082E07
    Using a deep socket wrench (21 mm) and press, slowly press in the generator coil.
    Text in Illustration 
    *1
    Deep Socket Wrench (21 mm)

  1. Install the 4 bolts.

    Torque:
    5.9 N*m{ 60 kgf*cm , 52 in.*lbf }


4. INSTALL GENERATOR BRUSH HOLDER ASSEMBLY

  1. A079315E20
    While pushing the 2 brushes into the brush holder, insert a pin with a diameter of 1.0 mm (0.0394 in.) into the brush holder hole.
    Text in Illustration 
    *1
    Pin

  1. A219667E01
    Install the brush holder to the generator coil with the 2 screws.

    Torque:
    1.8 N*m{ 18 kgf*cm , 16 in.*lbf }

    Text in Illustration 
    *1
    Pin

  1. Pull out the pin from the brush holder.


5. INSTALL TERMINAL INSULATOR

  1. A219668
    Install the terminal insulator to the generator coil.

    NOTICE:
    Make sure the terminal insulator is installed facing the proper direction.


6. INSTALL GENERATOR REAR END COVER
  1. Install the generator rear end cover to the generator coil with the 3 nuts.

    Torque:
    4.6 N*m{ 46 kgf*cm , 40 in.*lbf }

  1. Install the cord clip with the nut.

    Torque:
    6.2 N*m{ 63 kgf*cm , 55 in.*lbf }


7. INSTALL GENERATOR PULLEY WITH CLUTCH
  1. Temporarily install the generator pulley with clutch by hand.

  1. Mount the generator in a vise between aluminum plates.

  1. A219555E01
    Install SST (A) and SST (B) to the generator pulley with clutch as shown in the illustration.
    SST
    09820-63021  
    Text in Illustration 
    *1
    Rotor Shaft

    NOTICE:
    Securely attach SST to the generator pulley with clutch and rotor shaft.

  1. A219557E02
    Using a wrench to hold SST (A), turn SST (B) clockwise to tighten the generator pulley with clutch.

    Torque:
    without SST:
    80 N*m{ 816 kgf*cm , 59 ft.*lbf }
    with SST:
    64 N*m{ 653 kgf*cm , 47 ft.*lbf }

    Text in Illustration 
    *1
    Fulcrum Length
    *a
    Hold
    V100135
    Turn

    NOTICE:
    Be careful as the generator pulley with clutch or rotor shaft may be damaged if the position of SST is not securely maintained while performing this operation.

    HINT:
    1. Use a torque wrench with a fulcrum length of 400 mm (15.7 in.). When using a torque wrench with a fulcrum length that is not 400 mm (15.7 in.), calculate the torque specification for the torque wrench and SST based on the "without SST" torque specification (Click here).
    2. Make sure SST and the wrench are connected in a straight line.

  1. Remove SST from the generator.

  1. Check that the generator pulley with clutch rotates smoothly.


8. INSTALL GENERATOR PULLEY CAP
  1. Install a new generator pulley cap to the generator pulley with clutch.

← INSPECTION (from Jan 2012)INSTALLATION (from Jan 2012) →