Air Conditioning Amplifier Communication Stop Mode
Circuit diagnosis · Vehicles built from Jan 2012
Versions by build date: Sep 2011 – Dec 2011 from Jan 2012
DESCRIPTION
| Detection Item |
Symptom |
Trouble Area |
| Air Conditioning Amplifier Communication Stop Mode |
Either condition is met:
|
|
WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- Inspect the fuses for circuits related to this system before performing the following inspection procedure.
- HINT:
- Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.
| 1. PRECAUTION |
- NOTICE:
- After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).
| NEXT | |
| 2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.
- CAUTION:
- For vehicles with an SRS system:
- Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
- NOTICE:
- When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).
| NEXT | |
| 3. CHECK FOR OPEN IN CAN BUS WIRE (AIR CONDITIONING AMPLIFIER ASSEMBLY CAN BRANCH WIRE) |
Disconnect the E35*1 or E81*2 air conditioning amplifier connector.

- *1: w/ Rear Air Conditioning System
*2: w/o Rear Air Conditioning System
- *1: w/ Rear Air Conditioning System
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
w/ Rear Air Conditioning System Tester Connection
Switch Condition
Specified Condition
E35-3 (CANH) - E35-4 (CANL)
Ignition switch off
54 to 69 Ω
w/o Rear Air Conditioning System Tester Connection
Switch Condition
Specified Condition
E81-11 (CANH) - E81-12 (CANL)
Ignition switch off
54 to 69 Ω
Text in Illustration *A
w/ Rear Air Conditioning System
*B
w/o Rear Air Conditioning System
*a
Front view of wire harness connector
(to Air Conditioning Amplifier Assembly)
|
|
||||
| OK | |
| 4. CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER ASSEMBLY - BATTERY AND BODY GROUND) |
Connect the cable to the negative (-) battery terminal.

- NOTICE:
- When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
w/ Rear Air Conditioning System Tester Connection
Condition
Specified Condition
E36-1 (GND) - Body ground
Always
Below 1 Ω
E36-2 (E1) - Body ground
Always
Below 1 Ω
w/o Rear Air Conditioning System Tester Connection
Condition
Specified Condition
E81-14 (GND) - Body ground
Always
Below 1 Ω
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
w/ Rear Air Conditioning System Tester Connection
Condition
Specified Condition
E36-6 (+B1) - Body ground
Always
11 to 14 V
E36-7 (+B2) - Body ground
Always
11 to 14 V
E36-5 (IG+) - Body ground
Ignition switch ON
11 to 14 V
w/ Rear Air Conditioning System Tester Connection
Condition
Specified Condition
E81-21 (+B1) - Body ground
Always
11 to 14 V
E81-1 (IG+) - Body ground
Ignition switch ON
11 to 14 V
| *A |
w/ Rear Air Conditioning System |
| *B |
w/o Rear Air Conditioning System |
| *a |
Front view of wire harness connector (to Air Conditioning Amplifier Assembly) |
|
|
||||
| OK | ||
| ||
