2011-2013 Land Cruiser · Service Manual Vehicle Interior

INSPECTION

Inspection · Vehicles built from Sep 2011


INSPECT REAR DOOR LOCK ASSEMBLY LH (w/o Double Locking System)

B184440E06
  1. Check the door lock motor operation.

    1. Apply battery voltage to the door lock motor connector and check the operation of the door lock motor.

      OK:
      Measurement Condition
      Specified Condition
      Battery positive (+) → 4 (L)
      Battery negative (-) → 1 (UL)
      Lock
      Battery positive (+) → 1 (UL)
      Battery negative (-) → 4 (L)
      Unlock

      1. If the result is not as specified, replace the door lock assembly.

  1. Check the detection switch.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Switch Condition
      Specified Condition
      6 (LSSR) - 9 (E)
      Unlock
      Below 1 Ω
      6 (LSSR) - 9 (E)
      Lock
      10 kΩ or higher

      1. If the result is not as specified, replace the door lock assembly.


INSPECT REAR DOOR LOCK ASSEMBLY LH (w/ Double Locking System)

B144119E04
  1. Check the door lock motor operation.

    1. Apply battery voltage to the door lock motor connector and check the operation of the door lock motor.

      OK:
      Measurement Condition
      Specified Condition
      Battery positive (+) → 2 (L)
      Battery negative (-) → 1 (UL)
      Lock
      Battery positive (+) → 1 (UL)
      Battery negative (-) → 2 (L)
      Unlock
      Battery positive (+) → 4 (DL)
      Battery negative (-) → 3 (UNDL)
      Set
      Battery positive (+) → 3 (UNDL)
      Battery negative (-) → 4 (DL)
      Unset

      1. If the result is not as specified, replace the door lock assembly.

  1. Check the detection switch.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Switch Condition
      Specified Condition
      5 (LSSR) - 6 (E)
      Unlock
      Below 1 Ω
      5 (LSSR) - 6 (E)
      Lock
      10 kΩ or higher

      1. If the result is not as specified, replace the door lock assembly.


INSPECT REAR DOOR LOCK ASSEMBLY RH (w/o Double Locking System)

B184441E05
  1. Check the door lock motor operation.

    1. Apply battery voltage to the door lock motor connector and check the operation of the door lock motor.

      OK:
      Measurement Condition
      Specified Condition
      Battery positive (+) → 4 (L)
      Battery negative (-) → 1 (UL)
      Lock
      Battery positive (+) → 1 (UL)
      Battery negative (-) → 4 (L)
      Unlock

      1. If the result is not as specified, replace the door lock assembly.

  1. Check the detection switch.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Switch Condition
      Specified Condition
      6 (LSSR) - 9 (E)
      Unlock
      Below 1 Ω
      6 (LSSR) - 9 (E)
      Lock
      10 kΩ or higher

      1. If the result is not as specified, replace the door lock assembly.


INSPECT REAR DOOR LOCK ASSEMBLY RH (w/ Double Locking System)

B144120E03
  1. Check the door lock motor operation.

    1. Apply battery voltage to the door lock motor connector and check the operation of the door lock motor.

      OK:
      Measurement Condition
      Specified Condition
      Battery positive (+) → 4 (L)
      Battery negative (-) → 3 (UL)
      Lock
      Battery positive (+) → 3 (UL)
      Battery negative (-) → 4 (L)
      Unlock
      Battery positive (+) → 2 (DL)
      Battery negative (-) → 1 (UNDL)
      Set
      Battery positive (+) → 1 (UNDL)
      Battery negative (-) → 2 (DL)
      Unset

      1. If the result is not as specified, replace the door lock assembly.

  1. Check the detection switch.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Switch Condition
      Specified Condition
      6 (LSSR) - 9 (E)
      Unlock
      Below 1 Ω
      6 (LSSR) - 9 (E)
      Lock
      10 kΩ or higher

      1. If the result is not as specified, replace the door lock assembly.

← REMOVAL (from Jan 2012)INSTALLATION (Sep 2011 – Dec 2011) →