2011-2013 Land Cruiser · Service Manual Vehicle Interior

REMOVAL

Removal / installation · Vehicles built from Jan 2012

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

HINT:
  1. Use the same procedures for the LH side and RH side.
  2. The procedures listed below are for the LH side.


1. PRECAUTION

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).


2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


3. REMOVE REAR DOOR ARMREST BASE PANEL ASSEMBLY LH

  1. B180908
    Using a moulding remover, detach the 7 claws.

  1. Disconnect the connector and remove the armrest base panel.


4. REMOVE REAR DOOR INSIDE HANDLE BEZEL LH

  1. B180907E01
    Using a screwdriver, detach the 4 claws and remove the rear door inside handle bezel LH.

    HINT:
    Tape the screwdriver tip before use.

    Text in Illustration 
    *1
    Protective Tape


5. REMOVE ASSIST GRIP COVER LH

  1. B180910
    Using a moulding remover, detach the 9 claws and remove the assist grip cover LH.


6. REMOVE COURTESY LIGHT ASSEMBLY (w/ Courtesy Light)

  1. E155902
    Detach the claw.

  1. Remove the courtesy light and then disconnect the connector.


7. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY LH

  1. B310802E01
    Remove the 3 screws.

  1. Remove the 9 clips.

  1. Remove the rear inner door glass weatherstrip LH together with the rear door trim board sub-assembly LH by pulling them upward in the order shown in the illustration.

    HINT:
    Make sure that the pin labeled A in the illustration is detached from the door panel.

  1. Disconnect the connector and remove the rear door trim board sub-assembly LH.

  1. B180913
    Disconnect the 2 cables from the rear door inside handle sub-assembly LH.


8. REMOVE REAR DOOR SERVICE HOLE COVER LH

  1. B183933E01
    Using a clip remover, detach the 6 clamps.

  1. Remove the bolt and disconnect the 2 connectors.

  1. Remove the rear door service hole cover LH.

    HINT:
    Remove the remaining tape on the door.


9. REMOVE REAR DOOR LOCK ASSEMBLY LH

  1. B180926
    Using a T30 ''TORX'' socket, remove the 3 screws and door lock.

    NOTICE:
    Be careful when removing the screws as the door lock may fall and become damaged.


10. REMOVE REAR DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY LH

  1. B180928E01
    Using a screwdriver, detach the claw.

    HINT:
    Tape the screwdriver tip before use.

    Text in Illustration 
    *1
    Protective Tape

  1. B180929
    Remove the rear door lock remote control cable assembly LH.


11. REMOVE REAR DOOR INSIDE LOCKING CABLE ASSEMBLY LH

  1. B180930E01
    Using a screwdriver, detach the 3 claws.

    HINT:
    Tape the screwdriver tip before use.

    Text in Illustration 
    *1
    Protective Tape

  1. B188530E03
    Remove the rear door inside locking cable assembly LH.
    Text in Illustration 
    *A
    w/o Double Lock
    *B
    w/ Double Lock

← REMOVAL (Sep 2011 – Dec 2011)INSPECTION (from Sep 2011) →